diff --git a/main.cpp b/main.cpp
new file mode 100644
index 0000000..59e36bd
--- /dev/null
+++ b/main.cpp
@@ -0,0 +1,428 @@
+
+#include <Arduino.h>
+#include <Wire.h>
+#include <Kalman.h> // Source: https://github.com/TKJElectronics/KalmanFilter
+#define gyroZ_OFF -0.22
+
+//#define stable_angle 178.2
+//#define stable_angle 58.8
+
+//#define stable_angle 301.75
+#define stable_angle 60.0
+Kalman kalmanZ;
+
+/* IMU Data */
+double accX, accY, accZ;
+double gyroX, gyroY, gyroZ;
+int16_t tempRaw;
+
+double gyroZangle; // Angle calculate using the gyro only
+double compAngleZ; // Calculated angle using a complementary filter
+double kalAngleZ;  // Calculated angle using a Kalman filter
+
+uint32_t timer;
+uint8_t i2cData[14]; // Buffer for I2C data
+
+/********************************************************************************/
+#include <SimpleFOC.h>
+//#include "common/foc_utils.h"
+#define swing_up_voltage 1.5 //V
+#define balance_voltage 10   //V
+#define min_voltage 9.5      //V
+/*
+  #define PID_P 0  //
+  #define PID_I 0   //
+  #define PID_D 1   //
+  #define LQR_K1 1  //
+  #define LQR_K2 0  //
+  #define LQR_K3 0.0  //
+*/
+float PID_P = 1; //
+float PID_I = 0; //
+float PID_D = 0; //
+/*
+//稳定器参数
+float LQR_K1 = 50;  //摇摆到平衡
+float LQR_K2 = 2;   //
+float LQR_K3 = 0.30; //
+
+float LQR_K1_1 = 50;   //平衡态
+float LQR_K2_1 = 2;   //
+float LQR_K3_1 = 0.15; //
+*/
+//倒立摆参数
+float LQR_K1 = 200;  //摇摆到平衡
+float LQR_K2 = 40;   //
+float LQR_K3 = 0.30; //
+
+float LQR_K1_1 = 200;   //平衡态
+float LQR_K2_1 = 15;   //
+float LQR_K3_1 = 0.15; //
+
+/*
+float LQR_K1 = 200;   //
+float LQR_K2 = 40;   //
+float LQR_K3 = 0.30; //
+*/
+/*单角度稳定
+
+float LQR_K1 = 80;  //平衡完成
+float LQR_K2 = 15;  //
+float LQR_K3 = 0.15;  //
+*/
+float OFFSET = 0;
+bool stable = 0, battery_low = 0;
+uint32_t last_unstable_time;
+//output=LQR_K1*PID+LQR_K2*p_vel + LQR_K3 * m_vel
+
+MagneticSensorI2C sensor = MagneticSensorI2C(AS5600_I2C);
+PIDController angle_pid = PIDController(PID_P, PID_I, PID_D, balance_voltage * 0.7, 20000);
+LowPassFilter lpf_throttle{0.00};
+// BLDC motor init
+BLDCMotor motor = BLDCMotor(5);
+// driver instance
+BLDCDriver3PWM driver = BLDCDriver3PWM(9, 10, 11, 8, 3);
+double rotationshift(double origin, double theta, double shift, bool y);
+double acc2rotation(double x, double y);
+float controllerLQR(float p_angle, float p_vel, float m_vel);
+float constrainAngle(float x);
+
+// instantiate the commander
+Commander command = Commander(Serial);
+//void onp(char *cmd) { command.scalar(&PID_P, cmd); }
+//void oni(char *cmd) { command.scalar(&PID_I, cmd); }
+//void ond(char *cmd) { command.scalar(&PID_D, cmd); }
+void onj(char *cmd) { command.scalar(&LQR_K1, cmd); }
+void onk(char *cmd) { command.scalar(&LQR_K2, cmd); }
+void onl(char *cmd) { command.scalar(&LQR_K3, cmd); }
+
+/********************************************************************************/
+void setup()
+{
+  Serial.begin(115200);
+  Wire.begin();
+
+  Wire.setClock(400000UL); // Set I2C frequency to 400kHz
+  Serial.println(((analogRead(A3) / 41.5)));
+  i2cData[0] = 7;    // Set the sample rate to 1000Hz - 8kHz/(7+1) = 1000Hz
+  i2cData[1] = 0x00; // Disable FSYNC and set 260 Hz Acc filtering, 256 Hz Gyro filtering, 8 KHz sampling
+  i2cData[2] = 0x00; // Set Gyro Full Scale Range to ±250deg/s
+  i2cData[3] = 0x00; // Set Accelerometer Full Scale Range to ±2g
+  while (i2cWrite(0x19, i2cData, 4, false))
+    ; // Write to all four registers at once
+  while (i2cWrite(0x6B, 0x01, true))
+    ; // PLL with X axis gyroscope reference and disable sleep mode
+
+  while (i2cRead(0x75, i2cData, 1))
+    ;
+  if (i2cData[0] != 0x68)
+  { // Read "WHO_AM_I" register
+    Serial.print(F("Error reading sensor"));
+    while (1)
+      ;
+  }
+
+  delay(100); // Wait for sensor to stabilize
+
+  /* Set kalman and gyro starting angle */
+  while (i2cRead(0x3B, i2cData, 6))
+    ;
+  accX = (int16_t)((i2cData[0] << 8) | i2cData[1]);
+  accY = (int16_t)((i2cData[2] << 8) | i2cData[3]);
+  accZ = (int16_t)((i2cData[4] << 8) | i2cData[5]);
+
+  // Source: http://www.freescale.com/files/sensors/doc/app_note/AN3461.pdf eq. 25 and eq. 26
+  // atan2 outputs the value of -π to π (radians) - see http://en.wikipedia.org/wiki/Atan2
+  // It is then converted from radians to degrees
+  // Eq. 25 and 26
+
+  double pitch = acc2rotation(accX, accY);
+
+  kalmanZ.setAngle(pitch);
+  gyroZangle = pitch;
+
+  timer = micros();
+
+  pinMode(4, OUTPUT);
+  digitalWrite(4, 1);
+  sensor.init(&Wire);
+  motor.linkSensor(&sensor);
+  // driver
+  driver.voltage_power_supply = 12;
+  driver.init();
+
+  // link the driver and the motor
+  motor.linkDriver(&driver);
+
+  // aligning voltage
+  motor.voltage_sensor_align = 3;
+
+  // choose FOC modulation (optional)
+  //motor.foc_modulation = FOCModulationType::SinePWM;
+  motor.foc_modulation = FOCModulationType::SpaceVectorPWM;
+
+  // set control loop type to be used
+  motor.controller = MotionControlType::torque;
+  //motor.controller = TorqueControlType::voltage;
+
+  motor.voltage_limit = balance_voltage;
+
+  motor.useMonitoring(Serial);
+  // initialize motor
+  motor.init();
+  // align encoder and start FOC
+  //motor.initFOC(4.5,Direction::CW);
+  //motor.initFOC(4.05, Direction::CCW);
+  motor.initFOC();
+  //motor.initFOC(2.6492,Direction::CW);
+  //command.add('p', onp, "p");
+  //command.add('i', oni, "i");
+  //command.add('d', ond, "d");
+  command.add('j', onj, "newj:");
+  command.add('k', onk, "newk:");
+  command.add('l', onl, "newl:");
+
+  digitalWrite(4, 0);
+}
+long loop_count = 0;
+float target_voltage;
+void loop()
+{
+
+  motor.loopFOC();
+
+  if (loop_count++ == 10)
+  {
+    /* Update all the values */
+    while (i2cRead(0x3B, i2cData, 14))
+      ;
+    accX = (int16_t)((i2cData[0] << 8) | i2cData[1]);
+    accY = (int16_t)((i2cData[2] << 8) | i2cData[3]);
+    accZ = (int16_t)((i2cData[4] << 8) | i2cData[5]);
+    tempRaw = (int16_t)((i2cData[6] << 8) | i2cData[7]);
+    gyroX = (int16_t)((i2cData[8] << 8) | i2cData[9]);
+    gyroY = (int16_t)((i2cData[10] << 8) | i2cData[11]);
+    gyroZ = (int16_t)((i2cData[12] << 8) | i2cData[13]);
+    ;
+
+    double dt = (double)(micros() - timer) / 1000000; // Calculate delta time
+    timer = micros();
+
+    // Source: http://www.freescale.com/files/sensors/doc/app_note/AN3461.pdf eq. 25 and eq. 26
+    // atan2 outputs the value of -π to π (radians) - see http://en.wikipedia.org/wiki/Atan2
+    // It is then converted from radians to degrees
+    // Eq. 25 and 26
+
+    double pitch = acc2rotation(accX, accY);
+    double gyroZrate = gyroZ / 131.0; // Convert to deg/s
+
+    kalAngleZ = kalmanZ.getAngle(pitch, gyroZrate + gyroZ_OFF, dt);
+
+    gyroZangle += (gyroZrate + gyroZ_OFF) * dt;
+    //gyroXangle += kalmanX.getRate() * dt; // Calculate gyro angle using the unbiased rate
+    //gyroYangle += kalmanY.getRate() * dt;
+
+    compAngleZ = 0.93 * (compAngleZ + (gyroZrate + gyroZ_OFF) * dt) + 0.07 * pitch;
+
+    // Reset the gyro angle when it has drifted too much
+    if (gyroZangle < -180 || gyroZangle > 180)
+      gyroZangle = kalAngleZ;
+
+      /* Print Data */
+#if 0 // Set to 1 to activate
+  Serial.print(accX); Serial.print("\t");
+  Serial.print(accY); Serial.print("\t");
+  Serial.print(accZ); Serial.print("\t");
+
+  Serial.print(gyroX); Serial.print("\t");
+  Serial.print(gyroY); Serial.print("\t");
+  Serial.print(gyroZ); Serial.print("\t");
+
+  Serial.print("\t");
+#endif
+#if 0
+    Serial.print(pitch);
+    Serial.print("\t");
+    Serial.print(gyroZangle);
+    Serial.print("\t");
+    Serial.print(compAngleZ);
+    Serial.print("\t");
+    Serial.print(kalAngleZ);
+    Serial.print("\t");
+
+    //Serial.print("\r\n");
+#endif
+    // calculate the pendulum angle
+    //LQR_K1 = analogRead(A3) / 10.0;
+    digitalWrite(3, 1);
+    //float pendulum_angle = constrainAngle(rotationshift(kalAngleZ * 3, 180.0, -180.0+OFFSET, 0.0) / 57.29578 + M_PI);
+    //float pendulum_angle = constrainAngle((kalAngleZ - stable_angle ) / 57.29578);
+    float pendulum_angle = constrainAngle((fmod(kalAngleZ * 3, 360.0) / 3.0 - stable_angle) / 57.29578);
+    if (abs(pendulum_angle) < 0.6) // if angle small enough stabilize 0.5~30°,1.5~90°
+    {
+      //target_voltage = controllerLQR(pendulum_angle, g.gyro.z, motor.shaftVelocity());
+
+      target_voltage = controllerLQR(angle_pid(pendulum_angle), gyroZrate / 57.29578, motor.shaftVelocity());
+
+      //digitalWrite(4, 1);
+    }
+    else // else do swing-up
+    {    // sets 1.5V to the motor in order to swing up
+      target_voltage = -_sign(gyroZrate) * swing_up_voltage;
+      digitalWrite(4, 0);
+    }
+
+    // set the target voltage to the motor
+    if (accZ < -13000 && ((accX * accX + accY * accY) > (14000 * 14000)))
+    {
+      motor.move(0);
+    }
+    else
+    {
+      motor.move(lpf_throttle(target_voltage));
+    }
+    command.run();
+    // restart the counter
+    loop_count = 0;
+    //Serial.print("kangle:");
+    driver.voltage_power_supply = analogRead(A3) / 41.5;
+    //Serial.println(driver.voltage_power_supply);
+    if ((analogRead(A3) / 41.5) < min_voltage && !battery_low)
+    {
+      battery_low = 1;
+      Serial.println("battery_low!!");
+      while (battery_low)
+      {
+        motor.loopFOC();
+        motor.move(0);
+        if (millis() % 500 < 250)
+          digitalWrite(4, 1);
+        else
+          digitalWrite(4, 0);
+      }
+    }
+    //Serial.print(",fangle:");
+    //Serial.print(constrainAngle(rotationshift(kalAngleZ * 3, 180.0, -180.0+OFFSET, 0.0) / 57.29578 + M_PI));
+
+    //Serial.println(fmod(kalAngleZ * 3, 360.0) / 3.0);
+    //Serial.print(",pid:");
+    //Serial.println(accX);
+    //Serial.print(angle_pid(pendulum_angle));
+    //Serial.print(",voltage:");
+    //Serial.print(target_voltage);
+    //Serial.print(",lpf_throttle:");
+    //Serial.println(lpf_throttle(target_voltage));
+    //Serial.print(",E_gle:");
+    //Serial.print(sensor.getAngle());
+    //Serial.print(",vel:");
+    //Serial.println(sensor.getVelocity());
+  }
+  
+    
+    
+  
+}
+
+// function constraining the angle in between -pi and pi, in degrees -180 and 180
+float constrainAngle(float x)
+{
+  x = fmod(x + M_PI, _2PI);
+  if (x < 0)
+    x += _2PI;
+  return x - M_PI;
+}
+// LQR stabilization controller functions
+// calculating the voltage that needs to be set to the motor in order to stabilize the pendulum
+float controllerLQR(float p_angle, float p_vel, float m_vel)
+{
+  // if angle controllable
+  // calculate the control law
+  // LQR controller u = k*x
+  //  - k = [40, 7, 0.3]
+  //  - k = [13.3, 21, 0.3]
+  //  - x = [pendulum angle, pendulum velocity, motor velocity]'
+  if (abs(p_angle) > 0.05)
+  {
+    last_unstable_time = millis();
+    stable = 0;
+    digitalWrite(4, 0);
+  }
+  if ((millis() - last_unstable_time) > 1000)
+  {
+    stable = 1;
+    digitalWrite(4, 1);
+  }
+
+  //Serial.println(stable);
+  float u;
+  if (!stable)
+  {
+    u = LQR_K1 * p_angle + LQR_K2 * p_vel + LQR_K3 * m_vel;
+  }
+  else
+  {
+    //u = LQR_K1 * p_angle + LQR_K2 * p_vel + LQR_K3 * m_vel;
+    u = LQR_K1_1 * p_angle + LQR_K2_1 * p_vel + LQR_K3_1 * m_vel;
+  }
+
+  // limit the voltage set to the motor
+  if (abs(u) > motor.voltage_limit * 0.7)
+    u = _sign(u) * motor.voltage_limit * 0.7;
+
+  return u;
+}
+/* mpu6050加速度转换为角度
+            acc2rotation(ax, ay)
+            acc2rotation(az, ay) */
+double acc2rotation(double x, double y)
+{
+  if (y < 0)
+  {
+    return atan(x / y) / 1.570796 * 90 + 180;
+  }
+  else if (x < 0)
+  {
+    return (atan(x / y) / 1.570796 * 90 + 360);
+  }
+  else
+  {
+    return (atan(x / y) / 1.570796 * 90);
+  }
+}
+
+/* mpu6050加速度转换为角度
+       rotationshift(original angle,+θ,shiftθ,0 is normal,1 is reverse)
+       rotationshift(0,30)=30
+       rotationshift(20,30)=50
+       rotationshift(0,30,1)=330
+       rotationshift(20,30,1)=310
+       rotationshift(0,0,-180,0)=-180
+*/
+double rotationshift(double origin, double theta, double shift = 0, bool y = false)
+{
+  static float origin_old;
+  if (abs(origin - origin_old) > 0.1)
+    origin_old += _sign(origin - origin_old) * 0.01;
+  else
+    origin_old = origin;
+
+  if (y == 0)
+  {
+    if (origin + theta > 360)
+      return origin + theta - 360 + shift;
+    else
+    {
+      return origin + theta + shift;
+    }
+  }
+  else
+  {
+
+    if (-(origin + theta) + 360 < 0)
+      return -(origin + theta) + 360 + 360 + shift;
+    else
+    {
+      return -(origin + theta) + 360 + shift;
+    }
+  }
+}