174 lines
5.3 KiB
Verilog
174 lines
5.3 KiB
Verilog
/*
|
|
Copyright 2020 Blue Liang, liangkangnan@163.com
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
|
|
module uart_tx(
|
|
|
|
input wire clk,
|
|
input wire rst,
|
|
|
|
input wire we_i,
|
|
input wire req_i,
|
|
input wire[31:0] addr_i,
|
|
input wire[31:0] data_i,
|
|
|
|
output reg[31:0] data_o,
|
|
output reg ack_o,
|
|
output wire tx_pin
|
|
|
|
);
|
|
|
|
|
|
localparam BAUD_115200 = 32'h1B8;
|
|
|
|
localparam S_IDLE = 4'b0001;
|
|
localparam S_START = 4'b0010;
|
|
localparam S_SEND_BYTE = 4'b0100;
|
|
localparam S_STOP = 4'b1000;
|
|
|
|
reg tx_data_valid;
|
|
reg tx_data_ready;
|
|
|
|
reg[3:0] state;
|
|
reg[15:0] cycle_cnt;
|
|
reg[3:0] bit_cnt;
|
|
reg[7:0] tx_data;
|
|
reg tx_reg;
|
|
|
|
localparam UART_CTRL = 4'h0;
|
|
localparam UART_STATUS = 4'h4;
|
|
localparam UART_BAUD = 4'h8;
|
|
localparam UART_TXDATA = 4'hc;
|
|
|
|
// addr: 0x00
|
|
// rw. bit[0]: tx enable, 1 = enable, 0 = disable
|
|
reg[31:0] uart_ctrl;
|
|
|
|
// addr: 0x04
|
|
// ro. bit[0]: tx busy, 1 = busy, 0 = idle
|
|
// must check this bit before tx data
|
|
reg[31:0] uart_status;
|
|
|
|
// addr: 0x08
|
|
// rw. clk div
|
|
reg[31:0] uart_baud;
|
|
|
|
|
|
assign tx_pin = tx_reg;
|
|
|
|
|
|
always @ (posedge clk) begin
|
|
if (rst == 1'b0) begin
|
|
uart_ctrl <= 32'h0;
|
|
uart_status <= 32'h0;
|
|
uart_baud <= BAUD_115200;
|
|
tx_data_valid <= 1'b0;
|
|
end else begin
|
|
if (we_i == 1'b1) begin
|
|
case (addr_i[3:0])
|
|
UART_CTRL: begin
|
|
uart_ctrl <= data_i;
|
|
end
|
|
UART_BAUD: begin
|
|
uart_baud <= data_i;
|
|
end
|
|
UART_TXDATA: begin
|
|
if (uart_ctrl[0] == 1'b1 && uart_status[0] == 1'b0) begin
|
|
tx_data <= data_i[7:0];
|
|
uart_status <= 32'h1;
|
|
tx_data_valid <= 1'b1;
|
|
end
|
|
end
|
|
endcase
|
|
end else begin
|
|
tx_data_valid <= 1'b0;
|
|
if (tx_data_ready == 1'b1) begin
|
|
uart_status <= 32'h0;
|
|
end
|
|
end
|
|
end
|
|
end
|
|
|
|
always @ (*) begin
|
|
if (rst == 1'b0) begin
|
|
data_o = 32'h0;
|
|
end else begin
|
|
case (addr_i[3:0])
|
|
UART_CTRL: begin
|
|
data_o = uart_ctrl;
|
|
end
|
|
UART_STATUS: begin
|
|
data_o = uart_status;
|
|
end
|
|
UART_BAUD: begin
|
|
data_o = uart_baud;
|
|
end
|
|
default: begin
|
|
data_o = 32'h0;
|
|
end
|
|
endcase
|
|
end
|
|
end
|
|
|
|
always @ (posedge clk) begin
|
|
if (rst == 1'b0) begin
|
|
state <= S_IDLE;
|
|
cycle_cnt <= 16'd0;
|
|
tx_reg <= 1'b0;
|
|
bit_cnt <= 4'd0;
|
|
tx_data_ready <= 1'b0;
|
|
end else begin
|
|
if (state == S_IDLE) begin
|
|
tx_reg <= 1'b1;
|
|
tx_data_ready <= 1'b0;
|
|
if (tx_data_valid == 1'b1) begin
|
|
state <= S_START;
|
|
cycle_cnt <= 16'd0;
|
|
bit_cnt <= 4'd0;
|
|
tx_reg <= 1'b0;
|
|
end
|
|
end else begin
|
|
cycle_cnt <= cycle_cnt + 16'd1;
|
|
if (cycle_cnt == uart_baud[15:0]) begin
|
|
cycle_cnt <= 16'd0;
|
|
case (state)
|
|
S_START: begin
|
|
tx_reg <= tx_data[bit_cnt];
|
|
state <= S_SEND_BYTE;
|
|
bit_cnt <= bit_cnt + 4'd1;
|
|
end
|
|
S_SEND_BYTE: begin
|
|
bit_cnt <= bit_cnt + 4'd1;
|
|
if (bit_cnt == 4'd8) begin
|
|
state <= S_STOP;
|
|
tx_reg <= 1'b1;
|
|
end else begin
|
|
tx_reg <= tx_data[bit_cnt];
|
|
end
|
|
end
|
|
S_STOP: begin
|
|
tx_reg <= 1'b1;
|
|
state <= S_IDLE;
|
|
tx_data_ready <= 1'b1;
|
|
end
|
|
endcase
|
|
end
|
|
end
|
|
end
|
|
end
|
|
|
|
endmodule
|