86 lines
1.8 KiB
INI
86 lines
1.8 KiB
INI
# script for ATMEL sam3, a CORTEX-M3 chip
|
|
#
|
|
# at91sam3u4e
|
|
# at91sam3u2e
|
|
# at91sam3u1e
|
|
# at91sam3u4c
|
|
# at91sam3u2c
|
|
# at91sam3u1c
|
|
#
|
|
# at91sam3s4c
|
|
# at91sam3s4b
|
|
# at91sam3s4a
|
|
# at91sam3s2c
|
|
# at91sam3s2b
|
|
# at91sam3s2a
|
|
# at91sam3s1c
|
|
# at91sam3s1b
|
|
# at91sam3s1a
|
|
#
|
|
# at91sam3A4C
|
|
# at91sam3A8C
|
|
# at91sam3X4C
|
|
# at91sam3X4E
|
|
# at91sam3X8C
|
|
# at91sam3X8E
|
|
# at91sam3X8H
|
|
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME sam3
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 64kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x4000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x4ba00477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
# 16K is plenty, the smallest chip has this much
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
$_TARGETNAME configure -event gdb-flash-erase-start {
|
|
halt
|
|
}
|
|
|
|
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
|
|
#
|
|
# Since we may be running of an RC oscilator, we crank down the speed a
|
|
# bit more to be on the safe side. Perhaps superstition, but if are
|
|
# running off a crystal, we can run closer to the limit. Note
|
|
# that there can be a pretty wide band where things are more or less stable.
|
|
|
|
adapter_khz 500
|
|
|
|
adapter_nsrst_delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|