tinyriscv-openocd/tcl/board/topas910.cfg

120 lines
2.8 KiB
INI

######################################
# Target: Toshiba TOPAS910 -- TMPA910 Starterkit
#
######################################
# We add to the minimal configuration.
source [find target/tmpa910.cfg]
######################
# Target configuration
######################
#$_TARGETNAME configure -event gdb-attach { reset init }
$_TARGETNAME configure -event reset-init { topas910_init }
proc topas910_init { } {
# Init PLL
# my settings
mww 0xf005000c 0x00000007
mww 0xf0050010 0x00000065
mww 0xf005000c 0x000000a7
sleep 10
mdw 0xf0050008
mww 0xf0050008 0x00000002
mww 0xf0050004 0x00000000
# NEW: set CLKCR5
mww 0xf0050054 0x00000040
#
sleep 10
# Init SDRAM
# _PMCDRV = 0x00000071;
# //
# // Initialize SDRAM timing paramater
# //
# _DMC_CAS_LATENCY = 0x00000006;
# _DMC_T_DQSS = 0x00000000;
# _DMC_T_MRD = 0x00000002;
# _DMC_T_RAS = 0x00000007;
#
# _DMC_T_RC = 0x0000000A;
# _DMC_T_RCD = 0x00000013;
#
# _DMC_T_RFC = 0x0000010A;
#
# _DMC_T_RP = 0x00000013;
# _DMC_T_RRD = 0x00000002;
# _DMC_T_WR = 0x00000002;
# _DMC_T_WTR = 0x00000001;
# _DMC_T_XP = 0x0000000A;
# _DMC_T_XSR = 0x0000000B;
# _DMC_T_ESR = 0x00000014;
#
# //
# // Configure SDRAM type parameter
# _DMC_MEMORY_CFG = 0x00008011;
# _DMC_USER_CONFIG = 0x00000011;
# // 32 bit memory interface
#
#
# _DMC_REFRESH_PRD = 0x00000A60;
# _DMC_CHIP_0_CFG = 0x000140FC;
#
# _DMC_DIRECT_CMD = 0x000C0000;
# _DMC_DIRECT_CMD = 0x00000000;
#
# _DMC_DIRECT_CMD = 0x00040000;
# _DMC_DIRECT_CMD = 0x00040000;
# _DMC_DIRECT_CMD = 0x00080031;
# //
# // Finally start SDRAM
# //
# _DMC_MEMC_CMD = MEMC_CMD_GO;
# */
mww 0xf0020260 0x00000071
mww 0xf4300014 0x00000006
mww 0xf4300018 0x00000000
mww 0xf430001C 0x00000002
mww 0xf4300020 0x00000007
mww 0xf4300024 0x0000000A
mww 0xf4300028 0x00000013
mww 0xf430002C 0x0000010A
mww 0xf4300030 0x00000013
mww 0xf4300034 0x00000002
mww 0xf4300038 0x00000002
mww 0xf430003C 0x00000001
mww 0xf4300040 0x0000000A
mww 0xf4300044 0x0000000B
mww 0xf4300048 0x00000014
mww 0xf430000C 0x00008011
mww 0xf4300304 0x00000011
mww 0xf4300010 0x00000A60
mww 0xf4300200 0x000140FC
mww 0xf4300008 0x000C0000
mww 0xf4300008 0x00000000
mww 0xf4300008 0x00040000
mww 0xf4300008 0x00040000
mww 0xf4300008 0x00080031
mww 0xf4300004 0x00000000
sleep 10
# adapter_khz NNNN
# remap off in case of IROM boot
mww 0xf0000004 0x00000001
}
# comment the following out if usinf J-Link, it soes not support DCC
arm7_9 dcc_downloads enable # Enable faster DCC downloads
#####################
# Flash configuration
#####################
#flash bank cfi <base> <size> <chip width> <bus width> <target#>
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME cfi 0x20000000 0x2000000 2 2 0