128 lines
3.6 KiB
INI
128 lines
3.6 KiB
INI
# script for stm32f3x family
|
|
|
|
#
|
|
# stm32 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32f3x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 16kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x4000
|
|
}
|
|
|
|
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
|
|
#
|
|
# Since we may be running of an RC oscilator, we crank down the speed a
|
|
# bit more to be on the safe side. Perhaps superstition, but if are
|
|
# running off a crystal, we can run closer to the limit. Note
|
|
# that there can be a pretty wide band where things are more or less stable.
|
|
adapter_khz 1000
|
|
|
|
adapter_nsrst_delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
# See STM Document RM0316
|
|
# Section 29.6.3 - corresponds to Cortex-M4 r0p1
|
|
set _CPUTAPID 0x4ba00477
|
|
} {
|
|
set _CPUTAPID 0x2ba01477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
if { [info exists BSTAPID] } {
|
|
set _BSTAPID $BSTAPID
|
|
} else {
|
|
# STM Document RM0316 rev 5 for STM32F302/303 B/C size
|
|
set _BSTAPID1 0x06422041
|
|
# STM Document RM0313 rev 3 for STM32F37x
|
|
set _BSTAPID2 0x06432041
|
|
# STM Document RM364 rev 1 for STM32F334
|
|
set _BSTAPID3 0x06438041
|
|
# STM Document RM316 rev 5 for STM32F303 6/8 size
|
|
# STM Document RM365 rev 3 for STM32F302 6/8 size
|
|
# STM Document RM366 rev 2 for STM32F301 6/8 size
|
|
set _BSTAPID4 0x06439041
|
|
# STM Document RM016 rev 5 for STM32F303 D/E size
|
|
set _BSTAPID5 0x06446041
|
|
}
|
|
|
|
if {[using_jtag]} {
|
|
swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
|
|
-expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
|
|
-expected-id $_BSTAPID4 -expected-id $_BSTAPID5
|
|
}
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME stm32f1x 0 0 0 0 $_TARGETNAME
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
proc stm32f3x_default_reset_start {} {
|
|
# Reset clock is HSI (8 MHz)
|
|
adapter_khz 1000
|
|
}
|
|
|
|
proc stm32f3x_default_examine_end {} {
|
|
# Enable debug during low power modes (uses more power)
|
|
mmw 0xe0042004 0x00000007 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
|
|
|
# Stop watchdog counters during halt
|
|
mww 0xe0042008 0x00001800 ;# DBGMCU_APB1_FZ = DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
}
|
|
|
|
proc stm32f3x_default_reset_init {} {
|
|
# Configure PLL to boost clock to HSI x 8 (64 MHz)
|
|
mww 0x40021004 0x00380400 ;# RCC_CFGR = PLLMUL[3:1] | PPRE1[2]
|
|
mwh 0x40021002 0x0100 ;# RCC_CR[31:16] = PLLON
|
|
mww 0x40022000 0x00000012 ;# FLASH_ACR = PRFTBE | LATENCY[1]
|
|
sleep 10 ;# Wait for PLL to lock
|
|
mww 0x40021004 0x00380402 ;# RCC_CFGR |= SW[1]
|
|
|
|
# Boost JTAG frequency
|
|
adapter_khz 8000
|
|
}
|
|
|
|
# Default hooks
|
|
$_TARGETNAME configure -event examine-end { stm32f3x_default_examine_end }
|
|
$_TARGETNAME configure -event reset-start { stm32f3x_default_reset_start }
|
|
$_TARGETNAME configure -event reset-init { stm32f3x_default_reset_init }
|
|
|
|
$_TARGETNAME configure -event trace-config {
|
|
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
|
# change this value accordingly to configure trace pins
|
|
# assignment
|
|
mmw 0xe0042004 0x00000020 0
|
|
}
|