76 lines
2.5 KiB
INI
76 lines
2.5 KiB
INI
# TI OMAP3530
|
|
# http://focus.ti.com/docs/prod/folders/print/omap3530.html
|
|
# Other OMAP3 chips remove DSP and/or the OpenGL support
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME omap3530
|
|
}
|
|
|
|
# ICEpick-C ... used to route Cortex, DSP, and more not shown here
|
|
source [find target/icepick.cfg]
|
|
|
|
# Subsidiary TAP: C64x+ DSP ... must enable via ICEpick
|
|
jtag newtap $_CHIPNAME dsp -irlen 38 -ircapture 0x25 -irmask 0x3f -disable
|
|
|
|
# Subsidiary TAP: CoreSight Debug Access Port (DAP)
|
|
if { [info exists DAP_TAPID] } {
|
|
set _DAP_TAPID $DAP_TAPID
|
|
} else {
|
|
set _DAP_TAPID 0x0b6d602f
|
|
}
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf \
|
|
-expected-id $_DAP_TAPID -disable
|
|
jtag configure $_CHIPNAME.cpu -event tap-enable \
|
|
"icepick_c_tapenable $_CHIPNAME.jrc 3"
|
|
|
|
# Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
|
|
if { [info exists JRC_TAPID] } {
|
|
set _JRC_TAPID $JRC_TAPID
|
|
} else {
|
|
set _JRC_TAPID 0x0b7ae02f
|
|
}
|
|
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
|
|
-expected-id $_JRC_TAPID
|
|
|
|
# GDB target: Cortex-A8, using DAP
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_a -dap $_CHIPNAME.dap
|
|
|
|
# SRAM: 64K at 0x4020.0000; use the first 16K
|
|
$_TARGETNAME configure -work-area-phys 0x40200000 -work-area-size 0x4000
|
|
|
|
###################
|
|
|
|
# the reset sequence is event-driven
|
|
# and kind of finicky...
|
|
|
|
# some TCK tycles are required to activate the DEBUG power domain
|
|
jtag configure $_CHIPNAME.jrc -event post-reset "runtest 100"
|
|
|
|
# have the DAP "always" be active
|
|
jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap"
|
|
|
|
proc omap3_dbginit {target} {
|
|
# General Cortex-A8 debug initialisation
|
|
cortex_a dbginit
|
|
# Enable DBGU signal for OMAP353x
|
|
$target mww phys 0x5401d030 0x00002000
|
|
}
|
|
|
|
# be absolutely certain the JTAG clock will work with the worst-case
|
|
# 16.8MHz/2 = 8.4MHz core clock, even before a bootloader kicks in.
|
|
# OK to speed up *after* PLL and clock tree setup.
|
|
adapter_khz 1000
|
|
$_TARGETNAME configure -event "reset-start" { adapter_khz 1000 }
|
|
|
|
# Assume SRST is unavailable (e.g. TI-14 JTAG), so we must assert reset
|
|
# ourselves using PRM_RSTCTRL. RST_GS (2) is a warm reset, like ICEpick
|
|
# would issue. RST_DPLL3 (4) is a cold reset.
|
|
set PRM_RSTCTRL 0x48307250
|
|
$_TARGETNAME configure -event reset-assert "$_TARGETNAME mww $PRM_RSTCTRL 2"
|
|
|
|
$_TARGETNAME configure -event reset-assert-post "omap3_dbginit $_TARGETNAME"
|