153 lines
3.8 KiB
C
153 lines
3.8 KiB
C
/*
|
|
* COMPILE: arm-none-eabi-gcc -mthumb -march=armv7-m ...
|
|
* ... plus, provide at least a default exception vector table.
|
|
*
|
|
* RUN: this is best run from SRAM. It starts at main() then triggers
|
|
* a fault before more than a handful of instructions have executed.
|
|
* Run each test case in two modes:
|
|
*
|
|
* (1) Faults caught on the Cortex-M3. Default handlers are usually
|
|
* loop-to-self NOPs, so a debugger won't notice faults until they
|
|
* halt the core and examine xSPR and other registers.
|
|
*
|
|
* To verify the fault triggered, issue "halt" from OpenOCD; you
|
|
* should be told about the fault and (some of) its details.
|
|
* Then it's time to run the next test.
|
|
*
|
|
* NOTE however that "reset" will restart everything; verify that
|
|
* case by observing your reset handler doing its normal work.
|
|
*
|
|
* (2) Faults intercepted by OpenOCD "vector_catch ..." commands.
|
|
*
|
|
* OpenOCD should tell you about the fault, and show the same
|
|
* details, without your "halt" command.
|
|
*
|
|
* Someday, a fancy version of this code could provide a vector table and
|
|
* fault handlers which use semihosting (when that works on Cortex-M3) to
|
|
* report what happened, again without needing a "halt" command.
|
|
*/
|
|
|
|
|
|
/* These symbols match the OpenOCD "cortex_m3 vector_catch" bit names. */
|
|
enum vc_case {
|
|
hard_err,
|
|
int_err,
|
|
bus_err,
|
|
state_err,
|
|
chk_err,
|
|
nocp_err,
|
|
mm_err,
|
|
reset,
|
|
};
|
|
|
|
/* REVISIT come up with a way to avoid recompiling, maybe:
|
|
* - write it in RAM before starting
|
|
* - compiled-in BKPT, manual patch of r0, then resume
|
|
* - ...
|
|
*/
|
|
|
|
#ifndef VC_ID
|
|
#warning "no VC_ID ... using reset"
|
|
#define VC_ID reset
|
|
#endif
|
|
|
|
int main(void) __attribute__ ((externally_visible, noreturn));
|
|
|
|
/*
|
|
* Trigger various Cortex-M3 faults to verify that OpenOCD behaves OK
|
|
* in terms of its vector_catch handling.
|
|
*
|
|
* Fault handling should be left entirely up to the application code
|
|
* UNLESS a "vector_catch" command tells OpenOCD to intercept a fault.
|
|
*
|
|
* See ARMv7-M architecure spec table B1-9 for the list of faults and
|
|
* their mappings to the vector catch bits.
|
|
*/
|
|
int main(void)
|
|
{
|
|
/* One test case for each vector catch bit. We're not doing
|
|
* hardware testing; so it doesn't matter when some DEMCR bits
|
|
* could apply in multiple ways.
|
|
*/
|
|
switch (VC_ID) {
|
|
|
|
/* "cortex_m3 vector_catch hard_err" */
|
|
case hard_err:
|
|
/* FORCED - Fault escalation */
|
|
|
|
/* FIXME code this */
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch int_err" */
|
|
case int_err:
|
|
/* STKERR -- Exception stack BusFault */
|
|
|
|
/* FIXME code this */
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch bus_err" */
|
|
case bus_err:
|
|
/* PRECISERR -- precise data bus read
|
|
* Here we assume a Cortex-M3 with 512 MBytes SRAM is very
|
|
* unlikely, so the last SRAM byte isn't a valid address.
|
|
*/
|
|
__asm__ volatile(
|
|
"mov r0, #0x3fffffff\n"
|
|
"ldrb r0, [r0]\n"
|
|
);
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch state_err" */
|
|
case state_err:
|
|
/* UNDEFINSTR -- architectural undefined instruction */
|
|
__asm__ volatile(".hword 0xde00");
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch chk_err" */
|
|
case chk_err:
|
|
/* UNALIGNED ldm */
|
|
__asm__ volatile(
|
|
"mov r0, #1\n"
|
|
"ldm r0, {r1, r2}\n"
|
|
);
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch nocp_err" */
|
|
case nocp_err:
|
|
/* NOCP ... Cortex-M3 has no coprocessors (like CP14 DCC),
|
|
* but these instructions are allowed by ARMv7-M.
|
|
*/
|
|
__asm__ volatile("mrc p14, 0, r0, c0, c5, 0");
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch mm_err" */
|
|
case mm_err:
|
|
/* IACCVIOL -- instruction fetch from an XN region */
|
|
__asm__ volatile(
|
|
"mov r0, #0xe0000000\n"
|
|
"mov pc, r0\n"
|
|
);
|
|
break;
|
|
|
|
/* "cortex_m3 vector_catch reset" */
|
|
case reset:
|
|
__asm__ volatile(
|
|
/* r1 = SYSRESETREQ */
|
|
"mov r1, #0x0004\n"
|
|
/* r1 |= VECTKEY */
|
|
"movt r1, #0x05fa\n"
|
|
/* r0 = &AIRCR */
|
|
"mov r0, #0xed00\n"
|
|
"add r0, #0xc\n"
|
|
"movt r0, #0xe000\n"
|
|
/* AIRCR = ... */
|
|
"str r1, [r0, #0]\n"
|
|
);
|
|
break;
|
|
}
|
|
|
|
/* don't return */
|
|
while (1)
|
|
continue;
|
|
}
|