148 lines
4.5 KiB
INI
Executable File
148 lines
4.5 KiB
INI
Executable File
# script for stm32f7x family
|
||
|
||
#
|
||
# stm32f7 devices support both JTAG and SWD transports.
|
||
#
|
||
source [find target/swj-dp.tcl]
|
||
source [find mem_helper.tcl]
|
||
|
||
if { [info exists CHIPNAME] } {
|
||
set _CHIPNAME $CHIPNAME
|
||
} else {
|
||
set _CHIPNAME stm32f7x
|
||
}
|
||
|
||
set _ENDIAN little
|
||
|
||
# Work-area is a space in RAM used for flash programming
|
||
# By default use 128kB
|
||
if { [info exists WORKAREASIZE] } {
|
||
set _WORKAREASIZE $WORKAREASIZE
|
||
} else {
|
||
set _WORKAREASIZE 0x20000
|
||
}
|
||
|
||
#jtag scan chain
|
||
if { [info exists CPUTAPID] } {
|
||
set _CPUTAPID $CPUTAPID
|
||
} else {
|
||
if { [using_jtag] } {
|
||
# See STM Document RM0385
|
||
# Section 40.6.3 - corresponds to Cortex-M7 with FPU r0p0
|
||
set _CPUTAPID 0x5ba00477
|
||
} {
|
||
set _CPUTAPID 0x5ba02477
|
||
}
|
||
}
|
||
|
||
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
||
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
||
|
||
if {[using_jtag]} {
|
||
jtag newtap $_CHIPNAME bs -irlen 5
|
||
}
|
||
|
||
set _TARGETNAME $_CHIPNAME.cpu
|
||
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
||
|
||
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
||
|
||
set _FLASHNAME $_CHIPNAME.flash
|
||
flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
|
||
|
||
# adapter speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
|
||
adapter_khz 2000
|
||
|
||
adapter_nsrst_delay 100
|
||
if {[using_jtag]} {
|
||
jtag_ntrst_delay 100
|
||
}
|
||
|
||
# use hardware reset, connect under reset
|
||
reset_config srst_only srst_nogate
|
||
|
||
if {![using_hla]} {
|
||
# if srst is not fitted use SYSRESETREQ to
|
||
# perform a soft reset
|
||
cortex_m reset_config sysresetreq
|
||
}
|
||
|
||
$_TARGETNAME configure -event examine-end {
|
||
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
||
mmw 0xE0042004 0x00000007 0
|
||
|
||
# Stop watchdog counters during halt
|
||
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
||
mmw 0xE0042008 0x00001800 0
|
||
}
|
||
|
||
$_TARGETNAME configure -event trace-config {
|
||
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
||
# change this value accordingly to configure trace pins
|
||
# assignment
|
||
mmw 0xE0042004 0x00000020 0
|
||
}
|
||
|
||
$_TARGETNAME configure -event reset-init {
|
||
# If the HSE was previously enabled and the external clock source
|
||
# disappeared, RCC_CR.HSERDY can get stuck at 1 and the PLL cannot be
|
||
# properly switched back to HSI. This situation persists even over a system
|
||
# reset, including a pin reset via SRST. However, activating the clock
|
||
# security system will detect the problem and clear HSERDY to 0, which in
|
||
# turn allows the PLL to switch back to HSI properly. Since we just came
|
||
# out of reset, HSEON should be 0. If HSERDY is 1, then this situation must
|
||
# have happened; in that case, activate the clock security system to clear
|
||
# HSERDY.
|
||
if {[mrw 0x40023800] & 0x00020000} {
|
||
mmw 0x40023800 0x00090000 0 ;# RCC_CR = CSSON | HSEON
|
||
sleep 10 ;# Wait for CSS to fire, if it wants to
|
||
mmw 0x40023800 0 0x00090000 ;# RCC_CR &= ~CSSON & ~HSEON
|
||
mww 0x4002380C 0x00800000 ;# RCC_CIR = CSSC
|
||
sleep 1 ;# Wait for CSSF to clear
|
||
}
|
||
|
||
# If the clock security system fired, it will pend an NMI. A pending NMI
|
||
# will cause a bad time for any subsequent executing code, such as a
|
||
# programming algorithm.
|
||
if {[mrw 0xE000ED04] & 0x80000000} {
|
||
# ICSR.NMIPENDSET reads as 1. Need to clear it. A pending NMI can’t be
|
||
# cleared by any normal means (such as ICSR or NVIC). It can only be
|
||
# cleared by entering the NMI handler or by resetting the processor.
|
||
echo "[target current]: Clock security system generated NMI. Clearing."
|
||
|
||
# Keep the old DEMCR value.
|
||
set old [mrw 0xE000EDFC]
|
||
|
||
# Enable vector catch on reset.
|
||
mww 0xE000EDFC 0x01000001
|
||
|
||
# Issue local reset via AIRCR.
|
||
mww 0xE000ED0C 0x05FA0001
|
||
|
||
# Restore old DEMCR value.
|
||
mww 0xE000EDFC $old
|
||
}
|
||
|
||
# Configure PLL to boost clock to HSI x 10 (160 MHz)
|
||
mww 0x40023804 0x08002808 ;# RCC_PLLCFGR 16 Mhz /10 (M) * 128 (N) /2(P)
|
||
mww 0x40023C00 0x00000107 ;# FLASH_ACR = PRFTBE | 7(Latency)
|
||
mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
|
||
sleep 10 ;# Wait for PLL to lock
|
||
mww 0x40023808 0x00009400 ;# RCC_CFGR_PPRE1 = 5(div 4), PPRE2 = 4(div 2)
|
||
mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
|
||
|
||
# Boost SWD frequency
|
||
# Do not boost JTAG frequency and slow down JTAG memory access or flash write algo
|
||
# suffers from DAP WAITs
|
||
if {[using_jtag]} {
|
||
[[target current] cget -dap] memaccess 16
|
||
} {
|
||
adapter_khz 8000
|
||
}
|
||
}
|
||
|
||
$_TARGETNAME configure -event reset-start {
|
||
# Reduce speed since CPU speed will slow down to 16MHz with the reset
|
||
adapter_khz 2000
|
||
}
|