412 lines
14 KiB
Tcl
412 lines
14 KiB
Tcl
|
|
# board(-config) specfic parameters file.
|
|
|
|
# set CFG_REFCLKFREQ [configC100 CFG_REFCLKFREQ]
|
|
proc config {label} {
|
|
return [dict get [configC100] $label ]
|
|
}
|
|
|
|
# show the value for the param. with label
|
|
proc showconfig {label} {
|
|
echo [format "0x%x" [dict get [configC100] $label ]]
|
|
}
|
|
|
|
# Telo board config
|
|
# when there are more then one board config
|
|
# use soft links to c100board-config.tcl
|
|
# so that only the right board-config gets
|
|
# included (just like include/configs/board-configs.h
|
|
# in u-boot.
|
|
proc configC100 {} {
|
|
# xtal freq. 24MHz
|
|
dict set configC100 CFG_REFCLKFREQ 24000000
|
|
|
|
# Amba Clk 165MHz
|
|
dict set configC100 CONFIG_SYS_HZ_CLOCK 165000000
|
|
dict set configC100 w_amba 1
|
|
dict set configC100 x_amba 1
|
|
# y = amba_clk * (w+1)*(x+1)*2/xtal_clk
|
|
dict set configC100 y_amba [expr ([dict get $configC100 CONFIG_SYS_HZ_CLOCK] * ( ([dict get $configC100 w_amba]+1 ) * ([dict get $configC100 x_amba]+1 ) *2 ) / [dict get $configC100 CFG_REFCLKFREQ]) ]
|
|
|
|
# Arm Clk 450MHz, must be a multiple of 25 MHz
|
|
dict set configC100 CFG_ARM_CLOCK 450000000
|
|
dict set configC100 w_arm 0
|
|
dict set configC100 x_arm 1
|
|
# y = arm_clk * (w+1)*(x+1)*2/xtal_clk
|
|
dict set configC100 y_arm [expr ([dict get $configC100 CFG_ARM_CLOCK] * ( ([dict get $configC100 w_arm]+1 ) * ([dict get $configC100 x_arm]+1 ) *2 ) / [dict get $configC100 CFG_REFCLKFREQ]) ]
|
|
|
|
|
|
}
|
|
|
|
# This should be called for reset init event handler
|
|
proc setupTelo {} {
|
|
|
|
# setup GPIO used as control signals for C100
|
|
setupGPIO
|
|
# This will allow acces to lower 8MB or NOR
|
|
lowGPIO5
|
|
# setup NOR size,timing,etc.
|
|
setupNOR
|
|
# setup internals + PLL + DDR2
|
|
initC100
|
|
}
|
|
|
|
|
|
proc setupNOR {} {
|
|
echo "Setting up NOR: 16MB, 16-bit wide bus, CS0"
|
|
# this is taken from u-boot/boards/mindspeed/ooma-darwin/board.c:nor_hw_init()
|
|
set EX_CSEN_REG [regs EX_CSEN_REG ]
|
|
set EX_CS0_SEG_REG [regs EX_CS0_SEG_REG ]
|
|
set EX_CS0_CFG_REG [regs EX_CS0_CFG_REG ]
|
|
set EX_CS0_TMG1_REG [regs EX_CS0_TMG1_REG ]
|
|
set EX_CS0_TMG2_REG [regs EX_CS0_TMG2_REG ]
|
|
set EX_CS0_TMG3_REG [regs EX_CS0_TMG3_REG ]
|
|
set EX_CLOCK_DIV_REG [regs EX_CLOCK_DIV_REG ]
|
|
set EX_MFSM_REG [regs EX_MFSM_REG ]
|
|
set EX_CSFSM_REG [regs EX_CSFSM_REG ]
|
|
set EX_WRFSM_REG [regs EX_WRFSM_REG ]
|
|
set EX_RDFSM_REG [regs EX_RDFSM_REG ]
|
|
|
|
# enable Expansion Bus Clock + CS0 (NOR)
|
|
mww $EX_CSEN_REG 0x3
|
|
# set the address space for CS0=16MB
|
|
mww $EX_CS0_SEG_REG 0x7ff
|
|
# set the CS0 bus width to 16-bit
|
|
mww $EX_CS0_CFG_REG 0x202
|
|
# set timings to NOR
|
|
mww $EX_CS0_TMG1_REG 0x03034006
|
|
mww $EX_CS0_TMG2_REG 0x04040002
|
|
#mww $EX_CS0_TMG3_REG
|
|
# set EBUS clock 165/5=33MHz
|
|
mww $EX_CLOCK_DIV_REG 0x5
|
|
# everthing else is OK with default
|
|
}
|
|
|
|
proc bootNOR {} {
|
|
set EXP_CS0_BASEADDR [regs EXP_CS0_BASEADDR]
|
|
set BLOCK_RESET_REG [regs BLOCK_RESET_REG]
|
|
set DDR_RST [regs DDR_RST]
|
|
|
|
# put DDR controller in reset (so that it comes reset in u-boot)
|
|
mmw $BLOCK_RESET_REG 0x0 $DDR_RST
|
|
# setup CS0 controller for NOR
|
|
setupNOR
|
|
# make sure we are accessing the lower part of NOR
|
|
lowGPIO5
|
|
# set PC to start of NOR (at boot 0x20000000 = 0x0)
|
|
reg pc $EXP_CS0_BASEADDR
|
|
# run
|
|
resume
|
|
}
|
|
proc setupGPIO {} {
|
|
echo "Setting up GPIO block for Telo"
|
|
# This is current setup for Telo (see sch. for details):
|
|
#GPIO0 reset for FXS-FXO IC, leave as input, the IC has internal pullup
|
|
#GPIO1 irq line for FXS-FXO
|
|
#GPIO5 addr22 for NOR flash (access to upper 8MB)
|
|
#GPIO17 reset for DECT module.
|
|
#GPIO29 CS_n for NAND
|
|
|
|
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
|
|
set GPIO_OE_REG [regs GPIO_OE_REG]
|
|
|
|
# set GPIO29=GPIO17=1, GPIO5=0
|
|
mww $GPIO_OUTPUT_REG [expr 1<<29 | 1<<17]
|
|
# enable [as output] GPIO29,GPIO17,GPIO5
|
|
mww $GPIO_OE_REG [expr 1<<29 | 1<<17 | 1<<5]
|
|
}
|
|
|
|
proc highGPIO5 {} {
|
|
echo "GPIO5 high"
|
|
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
|
|
# set GPIO5=1
|
|
mmw $GPIO_OUTPUT_REG [expr 1 << 5] 0x0
|
|
}
|
|
|
|
proc lowGPIO5 {} {
|
|
echo "GPIO5 low"
|
|
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
|
|
# set GPIO5=0
|
|
mmw $GPIO_OUTPUT_REG 0x0 [expr 1 << 5]
|
|
}
|
|
|
|
proc boardID {id} {
|
|
# so far built:
|
|
# 4'b1111
|
|
dict set boardID 15 name "EVT1"
|
|
dict set boardID 15 ddr2size 128M
|
|
# dict set boardID 15 nandsize 1G
|
|
# dict set boardID 15 norsize 16M
|
|
# 4'b0000
|
|
dict set boardID 0 name "EVT2"
|
|
dict set boardID 0 ddr2size 128M
|
|
# 4'b0001
|
|
dict set boardID 1 name "EVT3"
|
|
dict set boardID 1 ddr2size 256M
|
|
# 4'b1110
|
|
dict set boardID 14 name "EVT3_old"
|
|
dict set boardID 14 ddr2size 128M
|
|
# 4'b0010
|
|
dict set boardID 2 name "EVT4"
|
|
dict set boardID 2 ddr2size 256M
|
|
|
|
return $boardID
|
|
}
|
|
|
|
|
|
# converted from u-boot/boards/mindspeed/ooma-darwin/board.c:ooma_board_detect()
|
|
# figure out what board revision this is, uses BOOTSTRAP register to read stuffed resistors
|
|
proc ooma_board_detect {} {
|
|
set GPIO_BOOTSTRAP_REG [regs GPIO_BOOTSTRAP_REG]
|
|
|
|
# read the current value of the BOOTSRAP pins
|
|
set tmp [mrw $GPIO_BOOTSTRAP_REG]
|
|
echo [format "GPIO_BOOTSTRAP_REG (0x%x): 0x%x" $GPIO_BOOTSTRAP_REG $tmp]
|
|
# extract the GPBP bits
|
|
set gpbt [expr ($tmp &0x1C00) >> 10 | ($tmp & 0x40) >>3]
|
|
|
|
# display board ID
|
|
echo [format "This is %s (0x%x)" [dict get [boardID $gpbt] $gpbt name] $gpbt]
|
|
# show it on serial console
|
|
putsUART0 [format "This is %s (0x%x)\n" [dict get [boardID $gpbt] $gpbt name] $gpbt]
|
|
# return the ddr2 size, used to configure DDR2 on a given board.
|
|
return [dict get [boardID $gpbt] $gpbt ddr2size]
|
|
}
|
|
|
|
proc configureDDR2regs_256M {} {
|
|
|
|
set DENALI_CTL_00_DATA [regs DENALI_CTL_00_DATA]
|
|
set DENALI_CTL_01_DATA [regs DENALI_CTL_01_DATA]
|
|
set DENALI_CTL_02_DATA [regs DENALI_CTL_02_DATA]
|
|
set DENALI_CTL_03_DATA [regs DENALI_CTL_03_DATA]
|
|
set DENALI_CTL_04_DATA [regs DENALI_CTL_04_DATA]
|
|
set DENALI_CTL_05_DATA [regs DENALI_CTL_05_DATA]
|
|
set DENALI_CTL_06_DATA [regs DENALI_CTL_06_DATA]
|
|
set DENALI_CTL_07_DATA [regs DENALI_CTL_07_DATA]
|
|
set DENALI_CTL_08_DATA [regs DENALI_CTL_08_DATA]
|
|
set DENALI_CTL_09_DATA [regs DENALI_CTL_09_DATA]
|
|
set DENALI_CTL_10_DATA [regs DENALI_CTL_10_DATA]
|
|
set DENALI_CTL_11_DATA [regs DENALI_CTL_11_DATA]
|
|
set DENALI_CTL_12_DATA [regs DENALI_CTL_12_DATA]
|
|
set DENALI_CTL_13_DATA [regs DENALI_CTL_13_DATA]
|
|
set DENALI_CTL_14_DATA [regs DENALI_CTL_14_DATA]
|
|
set DENALI_CTL_15_DATA [regs DENALI_CTL_15_DATA]
|
|
set DENALI_CTL_16_DATA [regs DENALI_CTL_16_DATA]
|
|
set DENALI_CTL_17_DATA [regs DENALI_CTL_17_DATA]
|
|
set DENALI_CTL_18_DATA [regs DENALI_CTL_18_DATA]
|
|
set DENALI_CTL_19_DATA [regs DENALI_CTL_19_DATA]
|
|
set DENALI_CTL_20_DATA [regs DENALI_CTL_20_DATA]
|
|
|
|
set DENALI_CTL_02_VAL 0x0100000000010100
|
|
set DENALI_CTL_11_VAL 0x433a32164a560a00
|
|
|
|
mw64bit $DENALI_CTL_00_DATA 0x0100000101010101
|
|
# 01_DATA mod [40]=1, enable BA2
|
|
mw64bit $DENALI_CTL_01_DATA 0x0100010100000001
|
|
mw64bit $DENALI_CTL_02_DATA $DENALI_CTL_02_VAL
|
|
mw64bit $DENALI_CTL_03_DATA 0x0102020202020201
|
|
mw64bit $DENALI_CTL_04_DATA 0x0000010100000001
|
|
mw64bit $DENALI_CTL_05_DATA 0x0203010300010101
|
|
mw64bit $DENALI_CTL_06_DATA 0x060a020200020202
|
|
mw64bit $DENALI_CTL_07_DATA 0x0000000300000206
|
|
mw64bit $DENALI_CTL_08_DATA 0x6400003f3f0a0209
|
|
mw64bit $DENALI_CTL_09_DATA 0x1a000000001a1a1a
|
|
mw64bit $DENALI_CTL_10_DATA 0x0120202020191a18
|
|
# 11_DATA mod [39-32]=16,more refresh
|
|
mw64bit $DENALI_CTL_11_DATA $DENALI_CTL_11_VAL
|
|
mw64bit $DENALI_CTL_12_DATA 0x0000000000000800
|
|
mw64bit $DENALI_CTL_13_DATA 0x0010002000100040
|
|
mw64bit $DENALI_CTL_14_DATA 0x0010004000100040
|
|
mw64bit $DENALI_CTL_15_DATA 0x04f8000000000000
|
|
mw64bit $DENALI_CTL_16_DATA 0x000000002cca0000
|
|
mw64bit $DENALI_CTL_17_DATA 0x0000000000000000
|
|
mw64bit $DENALI_CTL_18_DATA 0x0302000000000000
|
|
mw64bit $DENALI_CTL_19_DATA 0x00001300c8030600
|
|
mw64bit $DENALI_CTL_20_DATA 0x0000000081fe00c8
|
|
|
|
set wr_dqs_shift 0x40
|
|
# start DDRC
|
|
mw64bit $DENALI_CTL_02_DATA [expr $DENALI_CTL_02_VAL | (1 << 32)]
|
|
# wait int_status[2] (DRAM init complete)
|
|
echo -n "Waiting for DDR2 controller to init..."
|
|
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
|
|
while { [expr $tmp & 0x040000] == 0 } {
|
|
sleep 1
|
|
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
|
|
}
|
|
echo "done."
|
|
|
|
# do ddr2 training sequence
|
|
# TBD (for now, if you need it, run trainDDR command)
|
|
}
|
|
|
|
# converted from u-boot/cpu/arm1136/comcerto/bsp100.c:config_board99()
|
|
# The values are computed based on Mindspeed and Nanya datasheets
|
|
proc configureDDR2regs_128M {} {
|
|
|
|
set DENALI_CTL_00_DATA [regs DENALI_CTL_00_DATA]
|
|
set DENALI_CTL_01_DATA [regs DENALI_CTL_01_DATA]
|
|
set DENALI_CTL_02_DATA [regs DENALI_CTL_02_DATA]
|
|
set DENALI_CTL_03_DATA [regs DENALI_CTL_03_DATA]
|
|
set DENALI_CTL_04_DATA [regs DENALI_CTL_04_DATA]
|
|
set DENALI_CTL_05_DATA [regs DENALI_CTL_05_DATA]
|
|
set DENALI_CTL_06_DATA [regs DENALI_CTL_06_DATA]
|
|
set DENALI_CTL_07_DATA [regs DENALI_CTL_07_DATA]
|
|
set DENALI_CTL_08_DATA [regs DENALI_CTL_08_DATA]
|
|
set DENALI_CTL_09_DATA [regs DENALI_CTL_09_DATA]
|
|
set DENALI_CTL_10_DATA [regs DENALI_CTL_10_DATA]
|
|
set DENALI_CTL_11_DATA [regs DENALI_CTL_11_DATA]
|
|
set DENALI_CTL_12_DATA [regs DENALI_CTL_12_DATA]
|
|
set DENALI_CTL_13_DATA [regs DENALI_CTL_13_DATA]
|
|
set DENALI_CTL_14_DATA [regs DENALI_CTL_14_DATA]
|
|
set DENALI_CTL_15_DATA [regs DENALI_CTL_15_DATA]
|
|
set DENALI_CTL_16_DATA [regs DENALI_CTL_16_DATA]
|
|
set DENALI_CTL_17_DATA [regs DENALI_CTL_17_DATA]
|
|
set DENALI_CTL_18_DATA [regs DENALI_CTL_18_DATA]
|
|
set DENALI_CTL_19_DATA [regs DENALI_CTL_19_DATA]
|
|
set DENALI_CTL_20_DATA [regs DENALI_CTL_20_DATA]
|
|
|
|
|
|
set DENALI_CTL_02_VAL 0x0100010000010100
|
|
set DENALI_CTL_11_VAL 0x433A42124A650A37
|
|
# set some default values
|
|
mw64bit $DENALI_CTL_00_DATA 0x0100000101010101
|
|
mw64bit $DENALI_CTL_01_DATA 0x0100000100000101
|
|
mw64bit $DENALI_CTL_02_DATA $DENALI_CTL_02_VAL
|
|
mw64bit $DENALI_CTL_03_DATA 0x0102020202020201
|
|
mw64bit $DENALI_CTL_04_DATA 0x0201010100000201
|
|
mw64bit $DENALI_CTL_05_DATA 0x0203010300010101
|
|
mw64bit $DENALI_CTL_06_DATA 0x050A020200020202
|
|
mw64bit $DENALI_CTL_07_DATA 0x000000030E0B0205
|
|
mw64bit $DENALI_CTL_08_DATA 0x6427003F3F0A0209
|
|
mw64bit $DENALI_CTL_09_DATA 0x1A00002F00001A00
|
|
mw64bit $DENALI_CTL_10_DATA 0x01202020201A1A1A
|
|
mw64bit $DENALI_CTL_11_DATA $DENALI_CTL_11_VAL
|
|
mw64bit $DENALI_CTL_12_DATA 0x0000080000000800
|
|
mw64bit $DENALI_CTL_13_DATA 0x0010002000100040
|
|
mw64bit $DENALI_CTL_14_DATA 0x0010004000100040
|
|
mw64bit $DENALI_CTL_15_DATA 0x0508000000000000
|
|
mw64bit $DENALI_CTL_16_DATA 0x000020472D200000
|
|
mw64bit $DENALI_CTL_17_DATA 0x0000000008000000
|
|
mw64bit $DENALI_CTL_18_DATA 0x0302000000000000
|
|
mw64bit $DENALI_CTL_19_DATA 0x00001400C8030604
|
|
mw64bit $DENALI_CTL_20_DATA 0x00000000823600C8
|
|
|
|
set wr_dqs_shift 0x40
|
|
# start DDRC
|
|
mw64bit $DENALI_CTL_02_DATA [expr $DENALI_CTL_02_VAL | (1 << 32)]
|
|
# wait int_status[2] (DRAM init complete)
|
|
echo -n "Waiting for DDR2 controller to init..."
|
|
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
|
|
while { [expr $tmp & 0x040000] == 0 } {
|
|
sleep 1
|
|
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
|
|
}
|
|
# This is not necessary
|
|
#mw64bit $DENALI_CTL_11_DATA [expr ($DENALI_CTL_11_VAL & ~0x00007F0000000000) | ($wr_dqs_shift << 40) ]
|
|
echo "done."
|
|
|
|
# do ddr2 training sequence
|
|
# TBD (for now, if you need it, run trainDDR command)
|
|
}
|
|
|
|
|
|
|
|
proc setupUART0 {} {
|
|
# configure UART0 to 115200, 8N1
|
|
set GPIO_LOCK_REG [regs GPIO_LOCK_REG]
|
|
set GPIO_IOCTRL_REG [regs GPIO_IOCTRL_REG]
|
|
set GPIO_IOCTRL_VAL [regs GPIO_IOCTRL_VAL]
|
|
set GPIO_IOCTRL_UART0 [regs GPIO_IOCTRL_UART0]
|
|
set UART0_LCR [regs UART0_LCR]
|
|
set LCR_DLAB [regs LCR_DLAB]
|
|
set UART0_DLL [regs UART0_DLL]
|
|
set UART0_DLH [regs UART0_DLH]
|
|
set UART0_IIR [regs UART0_IIR]
|
|
set UART0_IER [regs UART0_IER]
|
|
set LCR_ONE_STOP [regs LCR_ONE_STOP]
|
|
set LCR_CHAR_LEN_8 [regs LCR_CHAR_LEN_8]
|
|
set FCR_XMITRES [regs FCR_XMITRES]
|
|
set FCR_RCVRRES [regs FCR_RCVRRES]
|
|
set FCR_FIFOEN [regs FCR_FIFOEN]
|
|
set IER_UUE [regs IER_UUE]
|
|
|
|
# unlock writing to IOCTRL register
|
|
mww $GPIO_LOCK_REG $GPIO_IOCTRL_VAL
|
|
# enable UART0
|
|
mmw $GPIO_IOCTRL_REG $GPIO_IOCTRL_UART0 0x0
|
|
# baudrate 115200
|
|
# This should really be amba_clk/(16*115200) but amba_clk=165MHz
|
|
set tmp 89
|
|
# Enable Divisor Latch access
|
|
mmw $UART0_LCR $LCR_DLAB 0x0
|
|
# set the divisor to $tmp
|
|
mww $UART0_DLL [expr $tmp & 0xff]
|
|
mww $UART0_DLH [expr $tmp >> 8]
|
|
# Disable Divisor Latch access
|
|
mmw $UART0_LCR 0x0 $LCR_DLAB
|
|
# set the UART to 8N1
|
|
mmw $UART0_LCR [expr $LCR_ONE_STOP | $LCR_CHAR_LEN_8 ] 0x0
|
|
# reset FIFO
|
|
mmw $UART0_IIR [expr $FCR_XMITRES | $FCR_RCVRRES | $FCR_FIFOEN ] 0x0
|
|
# enable FFUART
|
|
mww $UART0_IER $IER_UUE
|
|
}
|
|
|
|
proc putcUART0 {char} {
|
|
|
|
set UART0_LSR [regs UART0_LSR]
|
|
set UART0_THR [regs UART0_THR]
|
|
set LSR_TEMT [regs LSR_TEMT]
|
|
|
|
# convert the 'char' to digit
|
|
set tmp [ scan $char %c ]
|
|
# /* wait for room in the tx FIFO on FFUART */
|
|
while {[expr [mrw $UART0_LSR] & $LSR_TEMT] == 0} { sleep 1 }
|
|
mww $UART0_THR $tmp
|
|
if { $char == "\n" } { putcUART0 \r }
|
|
}
|
|
|
|
proc putsUART0 {str} {
|
|
set index 0
|
|
set len [string length $str]
|
|
while { $index < $len } {
|
|
putcUART0 [string index $str $index]
|
|
set index [expr $index + 1]
|
|
}
|
|
}
|
|
|
|
|
|
proc trainDDR2 {} {
|
|
set ARAM_BASEADDR [regs ARAM_BASEADDR]
|
|
|
|
# you must have run 'reset init' or u-boot
|
|
# load the training code to ARAM
|
|
load_image ./images/ddr2train.bin $ARAM_BASEADDR bin
|
|
# set PC to start of NOR (at boot 0x20000000 = 0x0)
|
|
reg pc $ARAM_BASEADDR
|
|
# run
|
|
resume
|
|
}
|
|
|
|
proc flashUBOOT {file} {
|
|
# this will update uboot on NOR partition
|
|
set EXP_CS0_BASEADDR [regs EXP_CS0_BASEADDR]
|
|
|
|
# setup CS0 controller for NOR
|
|
setupNOR
|
|
# make sure we are accessing the lower part of NOR
|
|
lowGPIO5
|
|
flash probe 0
|
|
echo "Erasing sectors 0-3 for uboot"
|
|
putsUART0 "Erasing sectors 0-3 for uboot\n"
|
|
flash erase_sector 0 0 3
|
|
echo "Programming u-boot"
|
|
putsUART0 "Programming u-boot..."
|
|
arm11 memwrite burst enable
|
|
flash write_image $file $EXP_CS0_BASEADDR
|
|
arm11 memwrite burst disable
|
|
putsUART0 "done.\n"
|
|
putsUART0 "Rebooting, please wait!\n"
|
|
reboot
|
|
} |