72 lines
2.3 KiB
INI
72 lines
2.3 KiB
INI
# This is the config for an Allwinner V3/V3s (sun8iw8).
|
|
#
|
|
# Notes:
|
|
# - Single core ARM Cortex-A7 with a maximum frequency of 1.2 GHz.
|
|
# - Thumb-2 Technology
|
|
# - Support NEON Advanced SIMD(Single Instruction Multiple Data)instruction
|
|
# for acceleration of media and signal processing functions
|
|
# - Support Large Physical Address Extensions(LPAE)
|
|
# - VFPv4 Floating Point Unit
|
|
# - 32KB L1 Instruction cache and 32KB L1 Data cache
|
|
# - 128KB L2 cache
|
|
# - has some integrated DDR2 RAM.
|
|
#
|
|
# Pins related for debug and bootstrap:
|
|
# JTAG
|
|
# JTAG_TMS PF0, SDC0_D1
|
|
# JTAG_TDI PF1, SDC0_D0
|
|
# JTAG_TDO PF3, SDC0_CMD
|
|
# JTAG_TCK PF5, SDC0_D2
|
|
# UART
|
|
# None of UART ports seems to be enabled by ROM.
|
|
# UART0_TX PF2, SDC0_CLK Per default disabled
|
|
# UART0_RX PF4, SDC0_D3 Per default disabled
|
|
# UART1_TX PE21 Per default disabled
|
|
# UART1_RX PE22 Per default disabled
|
|
# UART2_TX PB0 Per default disabled
|
|
# UART2_RX PB1 Per default disabled
|
|
#
|
|
# JTAG is enabled by default after power on on listed JTAG_* pins. So far the
|
|
# boot sequence is:
|
|
# Time Action
|
|
# 0000ms Power ON
|
|
# 0200ms JTAG enabled
|
|
# 0220ms JTAG pins switched to SD mode
|
|
#
|
|
# The time frame of 20ms can be not enough to init and halt the CPU. In this
|
|
# case I would recommend to set: "adapter_khz 15000"
|
|
# To get more or less precise timings, the board should provide reset pin,
|
|
# or some bench power supply with remote function. In my case I used
|
|
# EEZ H24005 with this command to power on and halt the target:
|
|
# "exec echo "*TRG" > /dev/ttyACM0; sleep 220; reset halt"
|
|
# After this it is possible to enable JTAG mode again from boot loader or OS.
|
|
# Following DAPs are available:
|
|
# dap[0]->MEM-AP AHB
|
|
# dap[1]->MEM-AP APB->CA7[0]
|
|
#
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME v3s
|
|
}
|
|
|
|
if { [info exists DAP_TAPID] } {
|
|
set _DAP_TAPID $DAP_TAPID
|
|
} else {
|
|
set _DAP_TAPID 0x5ba00477
|
|
}
|
|
|
|
# No NRST or SRST is present on the SoC. Boards may provide
|
|
# some sort of Power cycle reset for complete board or SoC.
|
|
# For this case we provide srst_pulls_trst so the board config
|
|
# only needs to set srst_only.
|
|
reset_config none srst_pulls_trst
|
|
|
|
jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x01 -irmask 0x0f \
|
|
-expected-id $_DAP_TAPID
|
|
|
|
# Add Cortex A7 core
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_a -chain-position $_CHIPNAME.dap
|