98 lines
3.4 KiB
INI
98 lines
3.4 KiB
INI
# Main file for NXP LPC17xx Cortex-M3
|
|
#
|
|
# !!!!!!
|
|
#
|
|
# This file should not be included directly, rather
|
|
# by the lpc1751.cfg, lpc1752.cfg, etc. which set the
|
|
# needed variables to the appropriate values.
|
|
#
|
|
# !!!!!!
|
|
|
|
# LPC17xx chips support both JTAG and SWD transports.
|
|
# Adapt based on what transport is active.
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
error "_CHIPNAME not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
|
|
}
|
|
|
|
# After reset the chip is clocked by the ~4MHz internal RC oscillator.
|
|
# When board-specific code (reset-init handler or device firmware)
|
|
# configures another oscillator and/or PLL0, set CCLK to match; if
|
|
# you don't, then flash erase and write operations may misbehave.
|
|
# (The ROM code doing those updates cares about core clock speed...)
|
|
#
|
|
# CCLK is the core clock frequency in KHz
|
|
if { [info exists CCLK] } {
|
|
set _CCLK $CCLK
|
|
} else {
|
|
set _CCLK 4000
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
error "_CPUTAPID not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
|
|
}
|
|
|
|
if { [info exists CPURAMSIZE] } {
|
|
set _CPURAMSIZE $CPURAMSIZE
|
|
} else {
|
|
error "_CPURAMSIZE not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
|
|
}
|
|
|
|
if { [info exists CPUROMSIZE] } {
|
|
set _CPUROMSIZE $CPUROMSIZE
|
|
} else {
|
|
error "_CPUROMSIZE not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
|
|
}
|
|
|
|
#delays on reset lines
|
|
adapter_nsrst_delay 200
|
|
jtag_ntrst_delay 200
|
|
|
|
#jtag newtap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -chain-position $_TARGETNAME
|
|
|
|
# The LPC17xx devices have 8/16/32kB of SRAM In the ARMv7-M "Code" area (at 0x10000000)
|
|
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_CPURAMSIZE
|
|
|
|
# The LPC17xx devies have 32/64/128/256/512kB of flash memory, managed by ROM code
|
|
# (including a boot loader which verifies the flash exception table's checksum).
|
|
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME lpc2000 0x0 $_CPUROMSIZE 0 0 $_TARGETNAME \
|
|
lpc1700 $_CCLK calc_checksum
|
|
|
|
# Run with *real slow* clock by default since the
|
|
# boot rom could have been playing with the PLL, so
|
|
# we have no idea what clock the target is running at.
|
|
adapter_khz 10
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
|
|
# "User Flash Mode" where interrupt vectors are _not_ remapped,
|
|
# and reside in flash instead).
|
|
#
|
|
# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
|
|
# Bit Symbol Value Description Reset
|
|
# value
|
|
# 0 MAP Memory map control. 0
|
|
# 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
|
|
# 1 User mode. The on-chip Flash memory is mapped to address 0.
|
|
# 31:1 - Reserved. The value read from a reserved bit is not defined. NA
|
|
#
|
|
# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user
|
|
|
|
mww 0x400FC040 0x01
|
|
}
|
|
|
|
# if srst is not fitted use VECTRESET to
|
|
# perform a soft reset - SYSRESETREQ is not supported
|
|
cortex_m reset_config vectreset
|