82 lines
3.2 KiB
INI
82 lines
3.2 KiB
INI
################################################################################
|
|
# Atmel AT91SAM9260-EK eval board
|
|
#
|
|
# http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933
|
|
#
|
|
# Atmel AT91SAM9260 : PLLA = 198.656 MHz, MCK = 99.328 MHz
|
|
# OSCSEL configured for external 32.768 kHz crystal
|
|
#
|
|
# 32-bit SDRAM : 2 x Micron MT48LC16M16A2, 4M x 16Bit x 4 Banks
|
|
#
|
|
################################################################################
|
|
|
|
# We add to the minimal configuration.
|
|
source [find target/at91sam9260.cfg]
|
|
|
|
# By default S1 is open and this means that NTRST is not connected.
|
|
# The reset_config in target/at91sam9260.cfg is overridden here.
|
|
# (or S1 must be populated with a 0 Ohm resistor)
|
|
reset_config srst_only
|
|
|
|
$_TARGETNAME configure -event reset-start {
|
|
# At reset CPU runs at 32.768 kHz.
|
|
# JTAG Frequency must be 6 times slower if RCLK is not supported.
|
|
jtag_rclk 5
|
|
halt
|
|
# RSTC_MR : enable user reset, MMU may be enabled... use physical address
|
|
mww phys 0xfffffd08 0xa5000501
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
|
|
|
|
mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main oscillator
|
|
sleep 20 # wait 20 ms
|
|
mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator
|
|
sleep 10 # wait 10 ms
|
|
mww 0xfffffc28 0x2060bf09 # CKGR_PLLAR: Set PLLA Register for 198.656 MHz
|
|
sleep 20 # wait 20 ms
|
|
mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler (divide by 2)
|
|
sleep 10 # wait 10 ms
|
|
mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLLA is selected (99.328 MHz)
|
|
sleep 10 # wait 10 ms
|
|
|
|
# Increase JTAG Speed to 6 MHz if RCLK is not supported
|
|
jtag_rclk 6000
|
|
|
|
arm7_9 dcc_downloads enable # Enable faster DCC downloads
|
|
|
|
mww 0xfffff870 0xffff0000 # PIO_ASR : Select peripheral function for D15..D31
|
|
mww 0xfffff804 0xffff0000 # PIO_PDR : Disable PIO function for D15..D31
|
|
|
|
mww 0xffffef1c 0x00010002 # EBI_CSA : Assign EBI Chip Select 1 to SDRAM, VDDIOMSEL set for +3V3 memory
|
|
|
|
mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM (2 x Micron MT48LC16M16A2 : 4M x 16Bit x 4 Banks)
|
|
|
|
mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP command
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All Banks Precharge' command
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x 'Auto-Refresh' Command
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x4
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load Mode Register' command
|
|
mww 0x20000000 0
|
|
mww 0xffffea00 0x0 # SDRAMC_MR : normal mode
|
|
mww 0x20000000 0
|
|
mww 0xffffea04 0x2b6 # SDRAMC_TR : Set refresh timer count to 7us
|
|
}
|