110 lines
3.4 KiB
INI
110 lines
3.4 KiB
INI
#
|
|
# Texas Instruments DaVinci family: TMS320DM355
|
|
#
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME dm355
|
|
}
|
|
|
|
# TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
|
|
# after JTAG reset until ICEpick is used to route them in.
|
|
set EMU01 "-disable"
|
|
|
|
# With EMU0/EMU1 jumpered *low* ARM and ETB are *enabled* without
|
|
# needing any ICEpick interaction.
|
|
#set EMU01 "-enable"
|
|
|
|
source [find target/icepick.cfg]
|
|
|
|
#
|
|
# Also note: when running without RTCK before the PLLs are set up, you
|
|
# may need to slow the JTAG clock down quite a lot (under 2 MHz).
|
|
#
|
|
|
|
# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
|
|
if { [info exists ETB_TAPID] } {
|
|
set _ETB_TAPID $ETB_TAPID
|
|
} else {
|
|
set _ETB_TAPID 0x2b900f0f
|
|
}
|
|
jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETB_TAPID $EMU01
|
|
jtag configure $_CHIPNAME.etb -event tap-enable \
|
|
"icepick_c_tapenable $_CHIPNAME.jrc 1"
|
|
|
|
# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
|
|
if { [info exists CPU_TAPID] } {
|
|
set _CPU_TAPID $CPU_TAPID
|
|
} else {
|
|
set _CPU_TAPID 0x07926001
|
|
}
|
|
jtag newtap $_CHIPNAME arm -irlen 4 -irmask 0xf -expected-id $_CPU_TAPID $EMU01
|
|
jtag configure $_CHIPNAME.arm -event tap-enable \
|
|
"icepick_c_tapenable $_CHIPNAME.jrc 0"
|
|
|
|
# Primary TAP: ICEpick (JTAG route controller) and boundary scan
|
|
if { [info exists JRC_TAPID] } {
|
|
set _JRC_TAPID $JRC_TAPID
|
|
} else {
|
|
set _JRC_TAPID 0x0b73b02f
|
|
}
|
|
jtag newtap $_CHIPNAME jrc -irlen 6 -irmask 0x3f -expected-id $_JRC_TAPID
|
|
|
|
jtag configure $_CHIPNAME.jrc -event setup \
|
|
"jtag tapenable $_CHIPNAME.etb; jtag tapenable $_CHIPNAME.arm"
|
|
|
|
################
|
|
|
|
# various symbol definitions, to avoid hard-wiring addresses
|
|
# and enable some sharing of DaVinci-family utility code
|
|
global dm355
|
|
set dm355 [ dict create ]
|
|
|
|
# Physical addresses for controllers and memory
|
|
# (Some of these are valid for many DaVinci family chips)
|
|
dict set dm355 sram0 0x00010000
|
|
dict set dm355 sram1 0x00014000
|
|
dict set dm355 sysbase 0x01c40000
|
|
dict set dm355 pllc1 0x01c40800
|
|
dict set dm355 pllc2 0x01c40c00
|
|
dict set dm355 psc 0x01c41000
|
|
dict set dm355 gpio 0x01c67000
|
|
dict set dm355 a_emif 0x01e10000
|
|
dict set dm355 a_emif_cs0 0x02000000
|
|
dict set dm355 a_emif_cs1 0x04000000
|
|
dict set dm355 ddr_emif 0x20000000
|
|
dict set dm355 ddr 0x80000000
|
|
dict set dm355 uart0 0x01c20000
|
|
dict set dm355 uart1 0x01c20400
|
|
dict set dm355 uart2 0x01e06000
|
|
|
|
source [find target/davinci.cfg]
|
|
|
|
################
|
|
# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K)
|
|
# and the ETB memory (4K) are other options, while trace is unused.
|
|
set _TARGETNAME $_CHIPNAME.arm
|
|
|
|
target create $_TARGETNAME arm926ejs -chain-position $_TARGETNAME
|
|
|
|
# NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
|
|
# and that the work area is used only with a kernel mmu context ...
|
|
$_TARGETNAME configure \
|
|
-work-area-virt [expr 0xfffe0000 + 0x4000] \
|
|
-work-area-phys [dict get $dm355 sram1] \
|
|
-work-area-size 0x4000 \
|
|
-work-area-backup 0
|
|
|
|
# be absolutely certain the JTAG clock will work with the worst-case
|
|
# CLKIN = 24 MHz (best case: 36 MHz) even when no bootloader turns
|
|
# on the PLL and starts using it. OK to speed up after clock setup.
|
|
adapter_khz 1500
|
|
$_TARGETNAME configure -event "reset-start" { adapter_khz 1500 }
|
|
|
|
arm7_9 fast_memory_access enable
|
|
arm7_9 dcc_downloads enable
|
|
|
|
# trace setup
|
|
etm config $_TARGETNAME 16 normal full etb
|
|
etb config $_TARGETNAME $_CHIPNAME.etb
|