115 lines
2.8 KiB
INI
115 lines
2.8 KiB
INI
# Cogent CSB337
|
|
# http://cogcomp.com/csb_csb337.htm
|
|
|
|
source [find target/at91rm9200.cfg]
|
|
|
|
# boots from NOR on CS0: 8 MBytes CFI flash, 16-bit bus
|
|
flash bank cfi 0x10000000 0x00800000 2 2 $_TARGETNAME
|
|
|
|
# ETM9 trace port connector present on this board, 16 data pins.
|
|
if { [info exists ETM_DRIVER] } {
|
|
etm config $_TARGETNAME 16 normal half $ETM_DRIVER
|
|
# OpenOCD may someday support a real trace port driver...
|
|
# system config file would need to configure it.
|
|
} else {
|
|
etm config $_TARGETNAME 16 normal half dummy
|
|
etm_dummy config $_TARGETNAME
|
|
}
|
|
|
|
proc csb337_clk_init { } {
|
|
# CPU is in Slow Clock Mode (32KiHz) ... needs slow JTAG clock
|
|
jtag_khz 8
|
|
|
|
# CKGR_MOR: start main oscillator (3.6864 MHz)
|
|
mww 0xfffffc20 0xff01
|
|
sleep 10
|
|
|
|
# CKGR_PLLAR: start PLL A for CPU and peripherals (184.32 MHz)
|
|
mww 0xfffffc28 0x20313e01
|
|
# CKGR_PLLBR: start PLL B for USB timing (96 MHz, with div2)
|
|
mww 0xfffffc2c 0x12703e18
|
|
# let PLLs lock
|
|
sleep 10
|
|
|
|
# PMC_MCKR: switch to CPU clock = PLLA, master clock = CPU/4
|
|
mww 0xfffffc30 0x0302
|
|
sleep 20
|
|
|
|
# CPU is in Normal Mode ... allows faster JTAG clock speed
|
|
jtag_khz 40000
|
|
}
|
|
|
|
proc csb337_nor_init { } {
|
|
# SMC_CSR0: adjust timings (10 wait states)
|
|
mww 0xffffff70 0x1100318a
|
|
|
|
flash probe 0
|
|
}
|
|
|
|
proc csb337_sdram_init { } {
|
|
# enable PIOC clock
|
|
mww 0xfffffc10 0x0010
|
|
# PC31..PC16 are D31..D16, with internal pullups like D15..D0
|
|
mww 0xfffff870 0xffff0000
|
|
mww 0xfffff874 0x0
|
|
mww 0xfffff804 0xffff0000
|
|
|
|
# SDRC_CR: set timings
|
|
mww 0xffffff98 0x2188b0d5
|
|
|
|
# SDRC_MR: issue all banks precharge to SDRAM
|
|
mww 0xffffff90 2
|
|
mww 0x20000000 0
|
|
|
|
# SDRC_MR: 8 autorefresh cycles
|
|
mww 0xffffff90 4
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
mww 0x20000000 0
|
|
|
|
# SDRC_MR: set SDRAM mode registers (CAS, burst len, etc)
|
|
mww 0xffffff90 3
|
|
mww 0x20000080 0
|
|
|
|
# SDRC_TR: set refresh rate
|
|
mww 0xffffff94 0x200
|
|
mww 0x20000000 0
|
|
|
|
# SDRC_MR: normal mode, 32 bit bus
|
|
mww 0xffffff90 0
|
|
mww 0x20000000 0
|
|
}
|
|
|
|
# The rm9200 chip has just been reset. Bring it up far enough
|
|
# that we can write flash or run code from SDRAM.
|
|
proc csb337_reset_init { } {
|
|
csb337_clk_init
|
|
|
|
# EBI_CSA: CS0 = NOR, CS1 = SDRAM
|
|
mww 0xffffff60 0x02
|
|
|
|
csb337_nor_init
|
|
csb337_sdram_init
|
|
|
|
# Update CP15 control register ... we don't seem to be able to
|
|
# read/modify/write its value through a TCL variable, so just
|
|
# write it. Fields are zero unless listed here ... and note
|
|
# that OpenOCD numbers this register "2", not "1" (!).
|
|
#
|
|
# - Core to use Async Clocking mode (so it uses 184 MHz most
|
|
# of the time instead of limiting to the master clock rate):
|
|
# iA(31) = 1, nF(30) = 1
|
|
# - Icache on (it's disabled now, slowing i-fetches)
|
|
# I(12) = 1
|
|
# - Reserved/ones
|
|
# 6:3 = 1
|
|
arm920t cp15 2 0xc0001078
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {csb337_reset_init}
|