echo Setting up for the FreeScale iMX31 Board.\n
# SETUP GDB :
#
# Common gdb setup for ARM CPUs
set complaints 1
set output-radix 10
set input-radix 10
set prompt (arm-gdb) 
set endian little
dir .


# DEFINE MACROS	:
#
# Create a "refresh" macro to update gdb's screens after the cpu
# has been stopped by the other CPU or following an "monitor allstop" 
define refresh
	monitor set hbreak
	cont
	monitor clear hbreak
end


# CONNECT TO TARGET :
target remote 127.0.0.1:3333
monitor reset run
#FIX!!!! should be reset init!
monitor reset halt

# iMX31 PDK board initialization commands:

#// init_ccm

monitor mww 0x53FC0000 0x040
monitor mww 0x53F80000 0x074B0B7D

#//532-133-66.5
#//monitor mww 0x53F80004 0xFF871D58
#//monitor mww 0x53F80010 0x0033280C

#// 399MHz - 26MHz input, PD=1,MFI=7, MFN=27, MFD=40
monitor mww 0x53F80004 0xFF871D50
monitor mww 0x53F80010 0x00271C1B

#// 208-104-52
#//monitor mww 0x53F80004 0xFF871D48
#//monitor mww 0x53F80010 0x04002000


#// Configure CPLD on CS5 
monitor mww 0xb8002050 0x0000DCF6
monitor mww 0xb8002054 0x444A4541
monitor mww 0xb8002058 0x44443302

#// Disable maximum drive strength for SDRAM/DDR lines by clearing DSE1 bits
#// in SW_PAD_CTL registers

#// SDCLK
monitor mww 0x43FAC26C 0
 
#// CAS
monitor mww 0x43FAC270 0
 
#// RAS
monitor mww 0x43FAC274 0
 
#// CS2 (CSD0)
monitor mww 0x43FAC27C 0x1000
    
#// DQM3
monitor mww 0x43FAC284 0
 
#// DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC)
monitor mww 0x43FAC288 0
monitor mww 0x43FAC28C 0
monitor mww 0x43FAC290 0
monitor mww 0x43FAC294 0
monitor mww 0x43FAC298 0
monitor mww 0x43FAC29C 0
monitor mww 0x43FAC2A0 0
monitor mww 0x43FAC2A4 0
monitor mww 0x43FAC2A8 0
monitor mww 0x43FAC2AC 0
monitor mww 0x43FAC2B0 0
monitor mww 0x43FAC2B4 0
monitor mww 0x43FAC2B8 0
monitor mww 0x43FAC2BC 0
monitor mww 0x43FAC2C0 0
monitor mww 0x43FAC2C4 0
monitor mww 0x43FAC2C8 0
monitor mww 0x43FAC2CC 0
monitor mww 0x43FAC2D0 0
monitor mww 0x43FAC2D4 0
monitor mww 0x43FAC2D8 0
monitor mww 0x43FAC2DC 0

#// Initialization script for 32 bit DDR on MX31 PDK 
monitor mww 0xB8001010 0x00000004
monitor mww 0xB8001004 0x006ac73a
monitor mww 0xB8001000 0x92100000
monitor mww 0x80000f00 0x12344321
monitor mww 0xB8001000 0xa2100000
monitor mww 0x80000000 0x12344321
monitor mww 0x80000000 0x12344321
monitor mww 0xB8001000 0xb2100000
#monitor char 0x80000033 0xda
monitor mwb 0x80000033 0xda
#monitor char 0x81000000 0xff
monitor mwb 0x81000000 0xff
monitor mww 0xB8001000 0x82226080
monitor mww 0x80000000 0xDEADBEEF
monitor mww 0xB8001010 0x0000000c

#  LOAD IMAGE :
#

# Load the program executable called "u-boot"
load test.elf

# Load the symbols for the program.
symbol-file test.elf

# RUN TO MAIN :
#
# Set a breakpoint at main().
#b reset
b main

# Run to the breakpoint.
c