This was somehow missed in the chip ID table and of course that's
exactly the one on my board (as such, tested on hardware).
Change-Id: I212d7c729d979e0357f1d4635f40935e25fe6ff3
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2260
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fitted to various Analog Devices ADuCM36x dev boards.
Change-Id: Ib3691704c0ecd2f8cba1abba284aee695d6bc135
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2244
Tested-by: jenkins
As Daniel pointed out, since the rewrite of the USB Blaster driver, the
initialization behaviour has change. The initial flush of the FIFOs is
not longer done with a specific USB setup packet, but with a write
filling up the blaster queues.
The problem is, quoting Daniel :
When the CPLD is in bit banging mode (as is usually the case), the
first 0x00 byte sets all pins to low and disables the output
driver. Disabling the output drivers is a few nanoseconds slower
than changing a pin from high to low, so I see a spike towards GND
on my reset line when that byte is sent over USB. The spike is too
short to have an effect on the board.
When the 4096 0x00 bytes are processed and the TMS=1 is to be
generated, all I see is several microseconds of low level on all
pins, resetting my board.
This patch changes the way the initialization is done :
- at driver init, nothing is sent towards the usb-blaster
This gives time for init script to setup PIN6 and PIN8 (resets)
- at the very first driver command, the initialization is done :
- the output is in bit bigbang mode
- the PIN6 and PIN8 are computed according to init script
- the 4096 computed output is sent
Change-Id: If7ceee957f6b59bcb27c8f912f1cfdd0f94f75ed
Reported-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/2229
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even though changing transport is impossible, reselecting it should be
harmless.
Change-Id: I6c1c2786134e826f47f848b590e6d712b6fd2206
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2251
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When you source a JTAG-SWD converter config, any other transport
doesn't make any sense, so just autoselect it right there.
Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369
Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2248
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In particular -f and -s options may contains paths that can easily
exceed the (old) 128 bytes buffer.
Change-Id: Ifc198536549f50663e8e588519bb9ef75dcd172c
Signed-off-by: Cristian Maglie <c.maglie@bug.st>
Reviewed-on: http://openocd.zylin.com/2241
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- stlink_usb_get_rw_status() had a bug where FAULT or WAIT responses
in read/write operations were ignored, leading to incomplete data.
- Added wrapper stlink_cmd_allow_retry to handle
SWD_AP_WAIT/SWD_DP_WAIT statuses in most commands. These statuses
appear if an SWD read or write received a WAIT ACK response from the
target more than 4 times in a row. The driver retries the operation
(with exponential backoff) before failing outright (in testing 1
retry was always enough.)
- As part of the implementation of stlink_cmd_allow_retry a large
number of lines of boilerplate were refactored.
- Fleshed out stlink_usb_error_check and added it to some more code
paths so WAIT or FAULT responses are logged to debug. WAIT responses
will be logged even if they are subsequently retried, which should
help in case the retries have subtle side effects (none
anticipated.)
Tested with two targets: STLINK F0 Discovery, Nordic NRF51822. Only
tested with STLINK V2 programmers.
Change-Id: I9af24e8f0121b035356dbb9978d6bbf4feb2e4d3
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2201
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to Nordic Semiconductor Product Anomaly Notice (document
NRF51822-PAN), item 16, some revisions of nRF51822 sometimes reset
without all RAM blocks enabled. This was noted on NRF51822-QFAA rev
CA/C0, only 8KiB of memory was accessible.
This patch turns on all RAM following a debugger induced reset
(matches specified behaviour.)
Change-Id: I4f8be4ec3d1271da7fe5bc9a084fdcb2968535bb
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2202
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the -irlen parameter was required even though it is not
a part of the SWD or CMSIS-DAP transports.
This may eventually need to be changed for CMSIS-DAP once that
supports JTAG as well.
Change-Id: Ia02b67840c19c7cf1c7a75063648c0174176a311
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2226
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This workaround broke usage with at least the I.MX6Q.
The comment implies that talking to the J-Link dongle itself should
fail if the target isn't reset, which sounds really strange. I'm
guessing it just triggered another bug in OpenOCD or Segger FW which
might have been fixed since. Revert and wait and see if there are any
failure reports.
Tested with Kwikstik (J-Link + Kinetis K40), not with the mentioned
adapter.
Change-Id: I97f555efe079bd99c098bf483491d9509b2363ad
Signed-off-by: Roy Spliet <rspliet@mpi-sws.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2147
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
During the initialisation a driver might need to communicate with the
target (e.g. sending jtag2swd sequence), so when doing so it should
honour the user-specified speed.
Change-Id: If84fea6057fda9edcf2c0a653edfbab2500e3cdd
[andrew.smirnov@gmail.com: fix khz/hz confusion]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2224
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Using custom build-time tools is always more problematic, especially
for cross-compiling.
This alternative implementation assumes "od" (IEEE Std 1003.1-2001)
and sed are available which should be the case for any reasonably
modern system.
Change-Id: I0208f475648c78e7dca127ff4bab60d314b2bf53
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2139
Tested-by: jenkins
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The Atmel SAMR21 is a Atmel SAMD21 with an Atmel RF233 in one package (two
dies). Tested with the SAMR21 Xplained Pro eval kit.
Change-Id: I1d79ea05834b925d7ec810527206fe86854e684b
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2194
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even if it does not return, the initialization will be failed.
But it is better to show why the error is caused.
Change-Id: I399c7c94a7156be22723a9715e594061bb414a7e
Signed-off-by: Masaki Muranaka <monaka@monami-ya.com>
Reviewed-on: http://openocd.zylin.com/2189
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If load_image address overlap with fast_data_area,
it will caouse different mysterius issues. This patch
should prevent it.
Change-Id: Ibc95e5aa3ac002a59755029496b6a72616e9287f
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1854
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis-K series has ID:0x001C0000 on MDM-AP IDR register.
Other Kinetis(L/M/V/E) series have ID:0x001C0020.
Change-Id: Iada37038cd239f7331ba80a3673b36bf7e18c555
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2195
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A previous commit changes the target name used by tcl scripts.
commit d9ba56c295
target: rename cortex_a8 to cortex_a
The current change renames target functions and definitions in the
implementation from cortex_a8 to cortex_a.
This prepares the implementation to support Cortex-A8, A9, A15-MPCore
in one place.
Change-Id: I73b5a38a92c12ba5bd3b806fbbb664817575a6d7
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1599
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with stm32f1x, stm32f4x and kl25 targets using SWD transport.
Change-Id: I118d07371b53f402ea9ac73f874460a309c05100
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1947
Tested-by: jenkins
ftime() is deprecated by POSIX.1-2008 and causes a warning on
FreeBSD.
The generic OpenOCD LOG_DEBUG implementation already outputs time of
an event with a millisecond precision.
Change-Id: Ic8e4ea27c268f07554ba519768b9bdfc4343f3e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2187
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes the issue of improper initialisation sequence and in
particular makes "cmsis_dap_vid_pid" config specification functional.
Not really elegant but it's in line with the ftdi driver and so can be
reworked in a uniform way later when the internal API is changed.
Change-Id: Ief9fc64ad0ac24e1c66727153f383e4f30a830c7
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2192
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is intended to fix cmsis_dap_vid_pid command but it doesn't
because cmsis-dap has only one transport and it's auto-selected from
"interface" command handler (before any other commands are run) and as
the result cmsis_dap_usb_open() is called too early.
Change-Id: Idaade73797d8df67a6439d096f6abc9736495599
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2191
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added Openocd commandline argument to ignore_error when the
read back TDO does not match to expected value specified with
TDO after masking with what is specified in MASK. This allows
to continue to play entire SVF file ignoring errors.
Error logs clearly show the failure reason and prints
read back TDO value.
Change-Id: I324f476fc16a003b35e6f2c5b63976431f49d54a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/2129
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the current reset_config doesn't specify availability of nTRST or
nSRST, just leave them alone, do not try to deassert them ever
(asserting would be prevented by the upper layer).
Change-Id: I90123c666e05a1c26f1e164625e82d766a3e3744
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2186
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Resistor hack is runtime-tested, other configs are based on
schematics.
Change-Id: I8daffa0434cd41d142fbec7c230a302284f7aa31
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2184
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Use a special signal instead of a dedicated swd mask. Amend
jtag-lock-pick_tiny_2 config accordingly.
Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2183
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Unfortunately, this means they're available for config files only
after selecting swd transport.
Change-Id: Ia2afc1f3bfdba8d81efbb8ab964b174c0f7e2811
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2182
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds -alias|-nalias options to ftdi_layout_signal command that
allow to declare a new signal based on an already defined one.
Change-Id: I552578ebcd12ae21957a1c0d3b7e878adeff6df0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2181
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Andrey Yurovsky
Spencer Oliver
Paul Fertser
Robert Jarzmik
Eldar Khayrullin
Oleksij Rempel
Cristian Maglie
Andrey Smirnov
Angus Gratton
Andrey Skvortsov
Andreas Fritiofson
Fredrik Hederstierna
Thomas Schmid
Masaki Muranaka
Nemui Trinomius
Kamal Dasu
Fatih Aşıcı
Kamal Dasu
Mathias K