Add a note to the docs about the original stlink being broken under linux.
Change-Id: Ib440d78e5c7d31eeace99f611a76fcf701bfb8bc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/433
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
The lm3s variant is not required as this is handled in the
target script - see tcl/target/stellaris.cfg.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
this will allow us to use multiple jlink at the same time as when
the USB-Address is specified the PID change from 0x0101 to
(0x101 + usb_adress)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This piggy backs on JTAG so it's not yet pretty, but that
seems unavoidable so far given today's OpenOCD internals.
SWD init and data transfer are unfinished and untested, but
that should cause no regressions, and will be addressed by
the time drivers start using this infrastructure. Checking
in whould get the code working better sooner, and turn up any
structural/architectural issues while they're easier to fix.
The debug adapter drivers will provide simple SWD driver
structs with methods that kick in as needed (instead of JTAG).
So far just one adapter driver has been updated (not yet
ready to use or circulate).
The biggest issues are probably
- fault handling, where the ARM Debug Interface V5 pipelining
needs work in both JTAG and SWD modes and
- missing rewrite of block I/O code to work on both of our
Cortex-ready transports (Current code is hard-wired to JTAG);
relates also to the pipelining issue.
- omitted support to activate/deactivate SWO/SWV trace (this is
technically trivial, but configuring what to trace is NOT.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
----
doc/openocd.texi | 17 ++
src/jtag/core.c | 3
src/jtag/interface.h | 4
src/jtag/jtag.h | 2
src/jtag/swd.h | 114 +++++++++++++++++++
src/jtag/tcl.c | 2
src/target/adi_v5_swd.c | 281 ++++++++++++++++++++++++++++++++++++++++++++++--
src/target/arm_adi_v5.c | 8 +
src/target/arm_adi_v5.h | 3
9 files changed, 425 insertions(+), 9 deletions(-)
STMicroelectronics controller SMI is not SPEAr specific.
Rename it and change name to every symbol in the code.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
this never panned out and there are enough mistakes in
the code that probably nobody used this.
Use the tcl server and implement a standalone http
app instead works fine.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Document "-n" option in manual;
Modify "echo" command definition as COMMAND_HANDLER to
easily add help message
Add help message aligned with manual.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone (again),
Watchpoints on xscale are quirky, so I thought a little explanation in the
user's manual was warranted.
Comments gratefully received.
Last one, Øyvind :-)
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
This new cmd adds the ability to choose the Cortex-M3
reset method used.
It defaults to using SRST for reset if available otherwise
it falls back to using NVIC VECTRESET. This is known to work
on all cores.
Move any luminary specific reset handling to the stellaris cfg file.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
ocd_ prefix is used internally in OpenOCD as a kludge more
or less to deal with the two kinds of commands that OpenOCD
has.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone. I noticed some incorrect information in the user manual
regarding how the vector table is handled on the xscale, so for your
consideration, here's a short patch that corrects it, and adds a
little more detail I thought might be helpful.
The documentation states that OpenOCD does not attempt to synchronize
the vector tables in memory with those stored in the "mini instruction
cache". In fact, on each resume it does copy from memory to the cache
all entries in the high and low tables that were not previously
defined using the 'xscale vector_table' command. (In
src/target/xscale.c, see xscale_update_vectors(), which is invoked by
xscale_resume().) I take advantage of this during Linux boot-up. The
extra detail describes in general terms how I do this.
Corrections, comments are of course gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Make it scriptable, so code can be conditionalized based on
what transport is in use for the session.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds the guts of a transport framework with initialization,
which should work with current JTAG-only configurations (tested
with FT2232).
Each debug adapter can declare the transports it supports, and
exactly one transport is initialized. (with its commands) in
any given OpenOCD session.
* Define a new "struct transport with init hooks and a few
"transport" subcommands to support it:
"list" ... list the transports configured (just "jtag" for now)
"select" ... makes the debug session use that transport
"init" ... initializes the selected transport (internal)
* "interface_transports" ... declares transports the current interface
can support. (Some will do this from C code instead, when there are
no hardware versioning (or other) issues to prevent it.
Plus some FT2232 tweaks, including a few to streamline upcoming
support for an SWD transport (initially for Luminary adapters).
Eventually src/jtag should probably become src/transport, moving
jtag-specific stuff to transport/jtag.
Signed-off-by: David Brownell <db@helium.(none)>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
1. fix some errors in jtag.txt(in my personal opinion, please review).
2. remove a broken link
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
There are a million reasons why cached protection state might
be stale: power cycling of target, reset, code executing on
the target, etc.
The "flash protect_check" command is now gone. This is *always*
executed when running a "flash info".
As a bonus for more a more robust approach, lots of code could
be deleted.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Flash probing must succeed for e.g. gdb load and automatic
hardware/software breakpoints to work.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Clean up the jtag/tcl.c file, which was one of the biggest and
messiest ones in that directory. Do it by splitting out all the
generic adapter commands to a separate "adapter.c" file (leaving
the "tcl.c" file holding only JTAG utilities).
Also rename the little-used "jtag interface" to "adapter_name", which
should have been at least re-categorized earlier (it's not jtag-only).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The mips_m4k_assert_reset has now been restructured
so the variant ejtag_srst is not required anymore.
The ejtag software reset will be used if the target does not
have srst connected.
Remove ejtag_srst from docs.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Globally rename "jtag_nsrst_assert_width" as "adapter_nsrst_assert_width",
and move it out of the "jtag" command group ... it needs to be used with
non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it
out of the "jtag" command group ... it needs to be used with non-JTAG
transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_khz" as "adapter_khz", and move it out of the "jtag"
command group ... it needs to be used with non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year. (We may want to
update it to include a nag message too.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This includes a driver and matching config file. This support needs to be
enabled through the initial "configure" (use "--enable-buspirate").
Signed-off-by: Michal Demin <michaldemin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We'll need to be able to work with debug adapter interfaces (drivers)
even when they're not used for JTAG ... for example, while there are
multi-transport drivers which support JTAG *and* several other
transports (or just one more, like SWD) there are also adapters
with more limited goals (and no JTAG support at all).
Start decoupling the two concepts ("debug adapter driver", "jtag")
by having two command groups, which initialize separately.
This will help us support OpenOCD sessions using only non-JTAG
transports, in which JTAG commands should not be registered.
Update docs to mention that the JTAG, SVF, and XSVF commands
won't work without a JTAG transport.
Note that at least commands working with SRST are still inappropriately
coupled to JTAG ... inappropriate because (a) SRST is not part of the
JTAG standard, for all that many platforms (like ARM) expect it; and also
(b) because they're used with non-JTAG debug and programming interfaces,
too. They should perhaps become generic "interface" operations at some
point. (Similarly with the clock rate to be used by a given adapter.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Talk more about "debug adapters" instead of only "dongles". Not all
adapters are discrete widgets; some are integrated onto boards. If
we only talk about "dongles" we rule out many valid setups, and help
confuse some users (who may be using Dongle-free environments).
Also start bringing out the point that JTAG isn't the only transport
protocol, even though OpenOCD historically presumes "all is JTAG".
(Not all debug adapters are JTAG adapters, or JTAG-only adapters.)
Plus a few minor fixes (spelling etc) in the vicinity of those changes,
and updates about FT2232H clocking issues (they can go faster than the
older chips, and can support adaptive clocking).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move semihosting cmd to the arm cmd group.
Targets that support semihosting will setup the
setup_semihosting callback function.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The Redbee USB is a small form-factor usb stick from Redwire, LLC
(www.redwirellc.com/store), built around a Freescale MC13224V
ARM7TDMI + 802.15.4 radio (plus antenna).
It includes an FT2232H for debugging, with Channel B connected to the
mc13224v's JTAG interface (unusual) and Channel A connected to UART1.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Redbee Econotag is an open hardware development kit from
Redwire, LLC (www.redwirellc.com/store), for the Freescale
MC13224V ARM7TDMI + 802.15.4 radio.
It includes both an MC13224V and an FT2232H (for JTAG and UART
support). It has flexible power supply options.
Additional features are:
- inverted-F pcb antenna
- 36 GPIO brought out to 0.1" pin header
(includes all peripheral pins)
- Reset button
- Two push buttons (on kbi1-5 and kbi0-4)
- USB-A connector, powered from USB
- up to 16V external input
- pads for optional buck inductor
- pads for optional 32.768kHz crystal
- 2x LEDS on TX_ON and RX_ON
[ dbrownell@users.sourceforge.net: shrink lines; texi ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Stellaris chips have a procedure for restoring the chip to
what's effectively the "as-manufactured" state, with all the
non-volatile memory erased. That includes all flash memory,
plus things like the flash protection bits and various control
words which can for example disable debugger access. clearly,
this can be useful during development.
Luminary/TI provides an MS-Windows utility to perform this
procedure along with its Stellaris developer kits. Now OpenOCD
users will no longer need to use that MS-Windows utility.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Be a closer match to what I've actually done for the past few cycles.
In particular, hold off pushing repository updates until after the
packages are published, as part of opening the merge window, and
mention the utility commands which actually create the archives.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Specifically the Linux issue of needing "udev" rules, and MS-Windows
needing driver configuration.
Also, update the existing udev note to use the correct name of that
rules file in the source tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sometimes MS-Windows users try to use filesystem names which include
the "#" character. That's generally unwise, since it begins Tcl
comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Not all cores and boards support adaptive clocking, so qualify
all advice to use it to depend on core and board support.
It's primarily ARM cores which support this; and many of the
newer ones (like Cortex-M series) don't.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Doxygen output was previously titled "OpenOCD Reference Manual",
which was quite misleading ... the User's Guide is the reference
manual which folk should consult about how to use the software.
Just rename it to match how it's been discussed previously, and to
bring out its intended audience: developers of this software. As a
rule, Doxygen is only for folk who work with the code it documents.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Have the User's Guide and BUG handling notes both reference
the fact that we now have a bug database at SourceForge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove long-obsolete text about "erase_check" affecting "flash info" output.
Move parts of that text to "protect_check", where it's still relevant; and
update the "flash info" description to mention the issue.
(This is still awkward. It might be best to make "protect_check" mirror
"erase_check" by dumping what it finds, so "flash info" doesn't dump any
potentially-stale cache info.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "-f" is a shortcut for "-c" ... and providing any "-c" options
means the "openocd.cfg" file isn't implicitly used. Both the User's
Guide and the manual page were weak on these points, which has led
to some confusion.
Also update the manual page to include highlights of the search path
mechanism, including the facts that it exists and that "-s" adds to it.
Stop saying only the current directory is involved; the OpenOCD
script library is quite significant.
(Missing: complete manpage coverage of the search path, including a
FILES section listing all components and saying where the script
library is found.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Highlight the needs to properly jumper development boards; to
make the OpenOCD configuration match the jumpering; and to have
a usable "reset-init" method when debugging early boot code.
Specific mention of the "ATX Mode" that seems useful on
many i.MX boards, forcing NAND boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Folk almost certainly want to have OpenOCD compute the checksum
when they modify the vector table. However, that almost guarantees
that "verify_image" will fail.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).
Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Capture various bits of useful information that have come up on the
list but haven't yet gotten into the documentation:
- Watchdog timers firing during JTAG debug need attention;
- Some chips have special registers to help JTAG debug;
- Cortex-M3 stepping example with IRQs and maskisr;
- Clarifications re adaptive clocking: not all ARMs do it, and
explain it a bit better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Based on notes from Tomek Cedro <tomek.cedro@gmail.com> and
Steve Franks <bahamasfranks@gmail.com>.
In the User's Guide, sort the list of operating systems reported
through Tcl with $ocd_HOSTOS ... and include FreeBSD.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "parport_port" commands generally don't *require* a port_number;
they're of the "apply any parameter, then print result" variety. Update
the User's Guide accordingly.
Some of those commands are intended to be write-once: parport_port,
and parport_cable. Say so.
Use proper EBNF for the parport_write_on_exit parameter.
Parport address 0xc8b8 is evidently mutant. Say so in the "parport.cfg"
file, to avoid breaking anyone with that mutant config. But update the
User's Guide to include a sane example for the LP2 port.
Finally document the "presto_serial" command.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.
Add TODO list entry re full support for NAND/NOR bank names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing. Improve and correct various helptexts.
Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.
Don't use "&function"; its name is its address. Line up struct
initializers properly. Remove some blank lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update/bugfix the "hello" example; emphasize using EBNF syntax,
matching the User's Guide. Correct the Texinfo style guide to
say EBNF, not BNF.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The issues is on Win32, which ignores case in filesystem
and thus doesn't tolerate the quilt "patches" directory.
Rename, and add "patches" to .gitignore so that developers
can choose to use quilt for local patch management.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Fix the User's Guide to say where the magic CP15 bits are defined;
and add comments in case someone provides mcr/mrc methods.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Deprecate the "pass an instruction opcode" flavor of cp15
access in favor of the "arm mcr ..." and "arm mrc ..."
commands, which offer fewer ways to break things.
Use the same EBNF syntax in the code as for the user's guide.
Update User's Guide to say where to find those magic values
(which table in the ARM920 TRM).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Freddie Chopin
Spencer Oliver
Timo Ketola
Erik Ahlén
Uwe Hermann
Spencer Oliver
Richard Uhler
Jie Zhang
Peter Horn
Michel Jaouen
Phil
Jean-Christophe PLAGNIOL-VILLARD
Aaron Carroll
David Brownell
Øyvind Harboe
Antonio Borneo
Mike Dunn
Catalin Patulea
David Brownell
Jun Ma
Marc Pignat
michal smulski
Michal Demin
Mariano Alvira
Peter Korsgaard