Active watchdog forces reset during armv7m_checksum_memory()
in verify_image command if run just after reset init.
COP watchdog in KL series and WDOG32 in KE1 series
have longer timeout however they need to be disabled too.
The change extends 'kinetis disable_wdog' command to optionally
probe the chip and use appropriate algorithm to disable watchdog.
Setting of cache type is also split from flash_support flags.
Tcl command 'kinetis disable_wdog' is called in reset-init event.
Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3901
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3925
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver probed and decoded chip repeatedly for each flash
bank. Bank ordering used global bank number so multi-target
configuration was broken.
The change introduces kinetis_probe_chip() which reads SIM SDID
and SIM FCFG registers, decodes Kinetis series and family
and fills struct kinetis_chip. This probe runs once for all banks.
struct kinetis_chip contains pointers to all flash banks embeded
in the MCU. It simplifies iteration over all or specific MCU banks.
kinetis_probe_chip() generates MCU name and some informational messages
are improved.
Change-Id: I990db5c63ba490667eec0e5459086d83936662fb
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3924
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Real time control MCU has a Cortex-M7 and numerous changes in flash layout.
Introduced a new ID of MDM-AP.
While on it a LOG_DEBUG format error fixed.
Change-Id: I1018660ce0c3dd63ac5e2563408fabff3c3daef7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3900
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Secure devices KL81Z7 and KL82Z7 have no SERIESID field in ID register
so they have to be decoded in Kx branch (not KLx).
The flash controller in KL8x and also in K8x devices does not implement
FTFx_CMD_BLOCKSTAT command. Fix kinetis_blank_check() to work properly
using FTFx_CMD_SECTSTAT command only.
Introduce a new flag FS_NO_CMD_BLOCKSTAT to avoid use of FTFx_CMD_BLOCKSTAT
on these devices.
Change-Id: I3ff58718480acd8cce69f618f71667b6b1d9c4f3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3898
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Config file renamed to ke0x.cfg and a notice added to texi.
While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG.
Removed per device configs as they set CHIPNAME and nothing more.
Let's use reasonably universal chip name 'ke' set in family config.
Change-Id: I313db87a59f25f968eb3c27df155780b67becee8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3897
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3896
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Before this change SAMD driver defined "sector" equal to a flash
protection block. Oversize sectors (16kB for the biggest flash size)
made problems for flashing firmware split to two or more parts.
Removed superfluous test of sector protection before erase.
Change-Id: I8e6a6bda6ccd91eda2df67ec48270c69faa1bdd1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3546
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
FWS=6 workaround removed, as this appears to be a copy-paste error
from the SAM3X family. Originally addressed in http://openocd.zylin.com/3837
but not all occurences were removed.
Atmel changed chip naming and removed 91 prefix for atsamg, samd...
Change-Id: Ia2b43da82b2ff9b1c85fdb456a0a198ab095243d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3926
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Supported SoCs: AR71xx, AR724x, AR91xx, AR93xx, QCA9558
Extended and revised version of my original patch submitted by Dmytro
here: http://openocd.zylin.com/#/c/3390
This driver is using pure SPI mode, so the flash base address is not
used except some flash commands (e.g. "flash program") need it to
distinguish the banks.
Example config with all 3 chip selects:
flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0
flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
Example usage:
> flash probe flash0
Found flash device 'win w25q128fv' (ID 0x001840ef)
flash 'ath79' found at 0x00000000
> flash probe flash1
No SPI flash found
> flash probe flash2
No SPI flash found
> flash banks
> flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000
reading 4096 bytes from flash @0x00000000
wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset
0x00000000 in 28.688066s (0.139 KiB/s)
Change-Id: I5feb697722c07e83a9c1b361a9db7b06bc699aa8
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: http://openocd.zylin.com/3612
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no need to implement scan code in functions
mips_ejtag_get_idcode/impcode(), use mips_ejtag_drscan_32().
Impcode/idcode saved in ejtag.info.
Reorder the code in the callers of this functions.
Change-Id: Ia829c783a0b24c6a65cade736113fa6f67b0a170
Signed-off-by: Salvador Arroyo <salvador@telecable.es>
Reviewed-on: http://openocd.zylin.com/4003
Tested-by: jenkins
Reviewed-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Breakpoint setting based on length (kind) only.
Added 16bit aligned 32bit software breakpoints
support and same filtering before setting
breakpoint.
Set the required isa bit in hardware breakpoints.
Drop the isa bit in software breakpoints.
Change-Id: I7020f27be16015194b76f385d9b8e5af496d0dfc
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4124
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Read and save configuration registers, up to 4.
Config3 holds the micromips implementation info.
Added isa implementation info to mips32_common.
Added isa filter to avoid common mistakes, but only
if one isa mode is implemented.
When resuming the isa requested is set if more than
one isa mode is implemented.
Change-Id: I1d6526c5525bffac8d75e031b842b2edc6310e28
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4123
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Needed to run in micromips mode. Seems that if an isa
is supported in debug mode it also supported in kernel
mode. The contrary is not true.
Change-Id: I1feb8e2c376f4db97089f05c20bc0cd177208fb3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4033
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Micromips is 16bit oriented, branch and jumps are
16 bit based. The upper half 16bits of a 32bit instruction
with the major opcode, must go first in the instruction
stream, hence the SWAP16 macro and swap16 array function,
needed if the code is written as 32 bit word in little endian
cores. Endianess info added to ejtag_iinfo. Pointer to
ejtag_info and isa field added to pracc context.
MIPS32 code are renamed to MIPS32_ISA_...
To select the isa, the new code has an additional isa parameter
(1 for micromips, 0 for mips32).
In JR instruction the isa bit must be set to execute
micromips code.
The suffix u is added to the OP codes to avoid signed/unsigned
comparison errors and to make sure the right shift is
performed logically.
The isa in debug mode is updated in the poll function.
Code for miniprograms, in kernel mode, need to be converted.
CFI code only for mips32.
Change-Id: I79a8b637d49b0e2d92b6dd5eb5aa8aa0520bf938
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4032
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Only reencoded MIPS32 instructions. Added some instructions
for crc code. Micromips isa in debug mode is only needed for
pic32mm cores. Pic32mz seems that only works with MIPS32
isa when in debug mode.
Change-Id: I07059e153a7000ea9204f20b6b37edf6a7623455
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4022
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This option is needed, for example, when exiting
debug mode in bmips targets. The last instruction
is a NOP, not a DERET. When working in async mode
this check is not done, mips32_pracc_queue_exec() pass
the parameter to mips32_pracc_exec() and never use it.
Change-Id: I4c7ed4feb1588b62e2645b955b501b6671113b36
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4021
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If max_code is reached realloc memory. If fails to realloc
the error is propagated and every call to pracc_add() returns
immediately. The exec function logs the error.
Change-Id: Idd4ed9d9b8b19b7d6842d0bc5ebb05f943726705
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4020
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
pracc_list points to an array with code in the lower half
and addr in the upper half. Change it to a struct with
an instruction field and an address field.
Requiered to make reallocation easier.
As a side effect the code is less quirky.
Change-Id: Ibf904a33a2f35a7f69284d2a2114f4b4ae79219f
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4019
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
MacOSX tool chain defines __unused in "sys/cdefs.h", causing a collision.
Remove the local define to avoid polluting the compilers internal
symbol namespace.
Change-Id: I16370c4518e6aeec482dd689e7db80628f846ee3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4118
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Less code and probably cleaner.
Don't check if it is ever ERROR_OK.
Change-Id: I1045b58fd4542ec24430332f49679364ae97b1dc
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4018
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Implement it as a function, the code was already in. Added optimize
option.
Change-Id: Ib9ad3f00d6c4f0b91c4e4960a50ec8d102f4e333
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4017
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In most of the cases there is no need to request execution,
the check for a new pracc access already does it.
Requesting execution if not needed makes execution slower and
code larger due the additional checks.
Reduce code in fasdata transfer function.
Call for execution when exiting debug.
Change-Id: I3b45f6d1f62da5fad3e3db84f82a9299b16e1bd9
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4010
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Struct mips32_pracc_context no more in use.
In current code cp0 reg/sel do not requires special handling.
In sync mode ctx.store_count not used, drop check.
In fasdata transfer function use mips32_pracc_read_ctrl_addr()
to reduce code.
Change-Id: Ibd4cfa5a44ebc106ed0db042f4e54a2e0b3d43cb
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4007
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
With this patch OpenOCD shuts down properly when errors occur in the
server instead of just calling exit().
Change-Id: I2ae1a6153dafc88667951cab9152941cb487be85
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3223
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Will be used later, allow queuing all needed scans in a pracc
access. This makes faster execution with ftdi based adapters
working in sync with pracc.
Added now because the overall code is shorter.
Change-Id: Ib32b89307b75785f88870db8d7c9255dc5bbd426
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4005
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Udev rules for Ambiq Micro ftdi based EVK's.
Two new vid:pid's: 2AEC:6010, and 2AEC:6011.
Udev rule for multi-target Debug board 2AEC:1106
Change-Id: Id7430d0c70647752375230f4024be9f7a2ba95ce
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3980
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The Silicon Labs EM3587 and EM3588 may have 512K of flash.
This fix allows for 512K to be specifiied on the command line
when flashing a device.
Change-Id: I18cc4bd0d14e1f2069066734a7396bcccf3de941
Signed-off-by: Byron Kubert <byronk@google.com>
Reviewed-on: http://openocd.zylin.com/3795
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The need for this due to AICE having 3 interfaces
(EP1 IN-Interrupt, EP2 OUT-Bulk, EP6 IN-Bulk).
Without it, the function will choose first two endpoint as
read_ep/write_ep. This filter will check transfer types
when get endpoint-id. Without this patch, AICE will not
get correct endpoint.
Change-Id: I4da93c7de41cd19e5095b4bfb42078b21f40b678
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/3218
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Make the 'offset' parameter optional, if omitted simply start at the
beginning of the flash bank.
Additionally, check if the argument is out of bounds of the flash bank.
Change-Id: Id1959eee5c395666c35f26342c3c50134dd564e5
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3858
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Default values for .first_bank_size_kb and .has_dual_banks fields
described in stm32lx_parts[] do not fully describe
the real device memory layouts.
Basing on:
STM32L0x1 RM0377
STM32L0x2 RM0376
STM32L0x3 RM0367
STM32Lxxxx RM0038
correct values for memory layouts were selected:
id = 0x447 STM32L0xx (Cat.5) <- dual bank flash
for size 192 or 128 KBytes, single bank for 64 KBytes
id = 0x436 STM32L1xx (Cat.4 / Cat.3 - Medium + /
High Density) <- only one size of the bank,
default values are correct
id = 0x437 STM32L1xx (Cat.5 / Cat.6) <- always dual bank,
but size of the bank can be different
For that reason .part_info field in struct stm32lx_flash_bank
is a dynamic field with fields copied from stm32lx_parts[]
and overwriten to correct values
for specific chips and memory sizes.
Change-Id: If638cb0a9916097bfd4eda77d64feaf1ef2d2147
Signed-off-by: Cezary Gapiński <cezary.gapinski@gmail.com>
Reviewed-on: http://openocd.zylin.com/4074
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Fix "couldn't use loader, falling back to page memory writes" error on
stm32l0 which was caused by the use of cortex-m3 instructions in the
flash loader code. The loader is rewritten using cortex-m0 compatible
instructions
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Change-Id: If23027b8e09f74e45129e1f8452a04bb994c424e
Reviewed-on: http://openocd.zylin.com/4036
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
'at91samd chip-erase' command did not work on secured device.
Fix it changing address of DSU.CTRL register
(see Atmel SAM D21 datasheet, 13.9. Intellectual Property Protection).
While on it check error return of DSU.CTRL write.
Change-Id: I83155a634a5458cdc0cc16c99c0e155eb1d8b3d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Thomas Irmen <tirmen@gmx.net>
Reviewed-on: http://openocd.zylin.com/4043
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Adapter clock frequency is set by 32-bit number and most adapters
limit the highest speed safely. There is no reason to impose strict
limit of 5000 kHz if some adapters can do more.
While on it give informative error message in case of zero adapter_khz.
Change-Id: I45c9804678e24496ea769ea9ca6036701b04dde9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3945
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tomas Vanek
Paul Fertser
Tobias Diedrich
Grzegorz Kostka
Forest Crossman
Moritz Fischer
Juha Niskanen
Salvador Arroyo
Salvador Arroyo
Matthias Welwarsky
Marc Schink
Karl Palsson
Byron Kubert
Hellosun Wu
Jan Čapek
CezaryGapinski
Armin van der Togt
Jerome Lambourg
Girts