BMIPS always needs 2 additional instructions to reach the core.
Seems there is a 2 instructions fifo between the tap and the core, or it behaves in this way.
No idea of the purpose of this fifo, I can only guess.
Of course function mips32_pracc_clean_text_jump() must add this additional instructions (NOPs).
Only tested on bcm3348..
Change-Id: I3183d3ce865d469d7262ba4b15446e5743a5f1df
Signed-off-by: Salvador Arroyo <salvador@telecable.es>
Reviewed-on: http://openocd.zylin.com/2270
Tested-by: jenkins
Reviewed-by: Kent Brinkley <jkbrinkley.imgtec@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Part IDs taken from
Atmel-42402C-SAM L22_Datasheet_Complete-01/2016
(revision C)
Change-Id: I1eb76a92097a8327da10faa0551e7fc962a549f8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3426
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Before this change jim_target_reset() checked examined state of a target
and failed without calling .assert_reset in particular target layer
(and without comprehensible warning to user).
Cortex-M target (which refuses access to DP under active SRST):
If connection is lost then reset process fails before asserting SRST
and connection with MCU is not restored.
This resulted in:
1) A lot of Cortex-M MCUs required use of reset button or cycling power
after firmware blocked SWD access somehow (sleep, misconfigured clock etc).
If firmware blocks SWD access early during initialization, a MCU could
become completely inaccessible by SWD.
2) If OpenOCD is (re)started and a MCU is in a broken state unresponsive
to SWD, reset command does not work even if it could help to restore communication.
Hopefully this scenario is not possible under full JTAG.
jim_target_reset() in target.c now does not check examined state
and delegates this task to a particular target. All targets have been checked
and xx_assert_reset() (or xx_deassert_reset()) procedures were changed
to check examined state if needed. Targets except arm11, cortex_a and cortex_m
just fail if target is not examined although it may be possible to use
at least hw reset. Left as TODO for developers familiar with these targets.
cortex_m_assert_reset(): memory access errors are stored
instead of immediate returning them to a higher level.
Errors from less important reads/writes are ignored.
Requested reset always leads to a configured action.
arm11_assert_reset() just asserts hw reset in case of not examined target.
cortex_a_assert_reset() works as usual in case of not examined target.
Change-Id: I84fa869f4f58e2fa83b6ea75de84440d9dc3d929
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2606
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Cortex-M0+ and M4 motor control MCUs KV10, KV11, KV30, KV31,
KV42, KV44 and KV46 added to SDID identification.
Watchdog disable code changed to work on Cortex-M0+ (KV1x)
Protection size set to 1K for 16K flash devices (KV10Z16)
- cherry picked from Andrey Smirnov's change #2051
Change-Id: Ia6f4868eaf7e2cb6ad6a736210c703a67e0027be
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3235
Tested-by: jenkins
Reviewed-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Change-Id: I55ab830aed34a02c53f3419facc81c7354368e30
Signed-off-by: Peter D. Gray <peter@conalgo.com>
Reviewed-on: http://openocd.zylin.com/3422
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Färber <afaerber@suse.de>
To avoid conflicts between flash drivers being added, consistently use
an alphabetical sort order for the three places new drivers get added:
* Makefile.am NOR_DRIVERS (note: automake disallows a trailing backslash)
* drivers.c struct flash_driver forward declarations
* drivers.c flash_drivers array
Change-Id: Idcd6a8e12821ef10958a6b3ad7bac0dc63cadd08
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3417
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Taken from git://git.ac6.fr/openocd commit e8ed67c42227b7072
STM32F446 (0x434) now is's own case.
Change-Id: I5061db7102b4c923c9f39d3d2f0cc69d29fca0a4
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3375
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Old code waited only for 7 bytes and didn't handle buffer wrap-around, but
was functional despite.
Change-Id: Iceaf7be1e51368b2ec0a8722cc9ac16d12f9aa63
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3140
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add new structure for for working with FPU thread in thread view.
This modification support both stacking.
When FPU is activated, LR must be validated to check if the FPU
register are push on the stack. This is mandatory to find the correct
stack pointer position.
the modified code was inspired and adapted from
88d2003bb8
Change-Id: I6641926aa14e7216cacb399cbc8bb0db324cc9fc
Signed-off-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-on: http://openocd.zylin.com/3397
Tested-by: jenkins
Reviewed-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-by: Harry Zhurov <harry.zhurov@gmail.com>
Reviewed-by: Anton Gusev
Reviewed-by: Михаил Цивинский <mtsivinsky@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no reason why not probe running target.
Initial gdb connect to running target is now possible without
halt in gdb-attach event.
Change-Id: Iacc4a231587d378168b18db871582f1086504831
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3382
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This feature is required for boards that use a programmatical way
to reset the cpu, like the TI Pandaboard with OMAP4. The board only
has a 14 pin JTAG header that doesn't feature SRST and is reset by
direct write to the PRM_RSTCTL register.
iMX6 can be reset through triggering the on-chip watchdog, but for these
methods to work reliably, access through the AHB-AP without interaction
with the CPU core is necessary.
Change-Id: I9a07a536adda83cc2f93e504384c8c7f0306220b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3359
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a 'ftdi_location' command to select an adapter by usb
bus number and port path.
This is helpful if you have a rack full of adapters in a testing or
manufacturing setup where the only constant is the physical usb bus
location of the adapter you want to address. Vid:Pid are not unique,
serial number _may_ be unique (and maybe not with embedded adapters) but
will change when a new target is plugged.
Specifying a location allows to understand instantly which board failed
bringup or testing.
Change-Id: I403c7c6c8e34fe42041b3f967db80f3160a4f1a3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3351
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add support for S6E2DH MainFlash. VFlash is not implemented.
Briefly tested with SK-FM4-176L-S6E2DH V110 board.
Change-Id: If7c523d8c75307bc1494bbf4cca3eed0272e8e01
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3158
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These appear to be just additional flash size configurations.
Entirely based on manual, untested.
Change-Id: I4460dc1a588335df8fc0a385d24513a4e35b6951
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3157
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On the ARM PB1176JZF-S the system comes up in secure monitor
mode after reset. However the modebits in CPSR form the value
28 (0x1c) and CPSR is 0x800001dc deeming it UNRECOGNIZED.
Define this mode to be synonymous to mode 22 (MON) and things
start to work like a charm.
Change-Id: I001f7773ee1076202c0c633e466d2d833f7a1413
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-on: http://openocd.zylin.com/3196
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds necessary code to obtain data from the Info region which is
not memory-mapped so can't be read the usual way.
With this "flash read_bank" and "flash verify_bank" commands should
start to work as expected for the Info memory block.
Change-Id: I57e4b80fff577500cfa85954b625fe9c9ff92aa5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3227
Tested-by: jenkins
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Instead of documenting the file path as a comment and inline-commenting
the THUMB bytecode, include the hex array via preprocessor.
This assures the path is actually up-to-date and facilitates updating
the code.
Change-Id: Ieb0a7cd0bc14882ac96750f524616d9768a0c6f5
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3134
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Instead of pointing to the assembler sources in a comment and
inline-commenting the THUMB bytecode, place the hex array alongside the
assembler sources and include it via preprocessor.
Originally inspired by a typo in the file path during driver development,
but it also facilitates making changes to the assembler sources.
A Makefile is provided to help automate updating the bytecode. It is not
integrated with the automake system to avoid forcing an ARM cross-compiler
onto every user, i.e. after modifying the sources they need to be rebuilt
in that directory before building the usual way. ARM_CROSS_COMPILE= can
be passed on the make command line to deal with native ARM toolchains
or with varying prefixes of cross-toolchains.
Change-Id: I00ceb980a68c8554a180dd13719ac77b677a8bcd
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3133
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The Spansion FM4 family of microcontrollers does not offer a way to
identify the chip model nor the flash size, except for Dual Flash vs.
regular layout. Therefore the family is passed as argument and
wildcard-matched - MB9BFx6x and S6E2CC families are supported.
Iterations showed that ...
1) Just doing the flash command sequence from SRAM loader code for each
half-word took 20 minutes for an 8 KB block.
2) Doing the busy-wait in the loader merely reduced the time to 19 minutes.
3) Significant performance gains were achieved by looping in loader code
rather than in OpenOCD and by maximizing the batch size across sectors,
getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB.
(Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.)
gcc, objcopy -Obinary and bin2char.sh are used for automating the
integration of hand-written assembler snippets.
Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Flash driver for at91sam4 cpu's has been enhanced to recognise and support the SAM4N family.
Change-Id: I50c471a6053b52edffd8efdd8abfe516cc5c55ee
Signed-off-by: Colin Helliwell <colin.helliwell@ln-systems.com>
Reviewed-on: http://openocd.zylin.com/3242
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Error found by static code analysis using the semantic pattern
null_ref2/mini_null_ref2.cocci, see coccinellery.org
Change-Id: Ic817c29f0ccf2b41fc8f7d9a480ad30d6e5b7ab8
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3364
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A copy-and-paste error in the arm_disassembler opcode evaluation
disabled the recognition of MRRC instructions.
According to the arm architecture ref. manual issue E or later, MRRC and MCRR
instructions are identified by opcode bits 20-27: MCRR = 0xc4, MRRC = 0xc5.
Error found by static code analysis using a semantic pattern to
detect duplicated tests xand.cocci, see coccinellery.org
Change-Id: Ic41426edb51c6816e11dc3d35ef9382ab34af486
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3363
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The flash info command on stellaris platformes
"TI/LMI Stellaris information ... rcc is ..., rcc2 is ..."
presented the actual RCC2 register as rcc and an uninitialized variable
as rcc2 due to a copy and paste error.
Found using the semantic pattern da/da.cocci, see coccinellery.org
Change-Id: I6f920fc3e07fdc085ea8e2248fbc9453eb8393dc
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3368
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A struct member has been initialized twice. Found using the semantic
pattern da/da.cocci, see coccinellery.org
Change-Id: I0320afd60f1ba505758cc5bc0adcf27f572492fb
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Obsolete C source code semicolons were removed using the semantic patch
semicolon/semicolon.cocci, see coccinellery.org
Change-Id: I153b4995a9e028ebaf5f58c947821dc78345a777
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3367
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Writing to Intel CFI flash with unaligned tail bytes raised a false
error message although all data was programmed successfully. e.g.:
> flash write_image image 0x602e0000 bin
> Programming at 0x602e0000, count 0x00000002 bytes remaining
> couldn't write word at base 0x60000000, address 0x602e0000
> error writing to flash at address 0x60000000 at offset 0x002e0000
Root cause for this false error was a mixup of two result variables
introduced with ecc8041c.
Change-Id: Ib6b85293dbed946a36a307e5b198c47b901145bf
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3233
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a nRF51822 variant, not a nRF51422 variant.
Change-Id: Ia199e0afa39408d7391a9655bad47eba2fd85f14
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3105
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Simplify by printing one component per call, instead of one complete ROM
Table per call. Print common information the same way for all components,
including ROM tables, because ROM tables (at least the top level) contain
useful information in their identification registers, such as the
manufacturer of the SoC.
Print component designer name using the JEP106 helper when available.
Change-Id: Ic51bccd98acfae6886243500153fbdd567be2fae
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3182
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: James Mastros <james@mastros.biz>
Tested with EES-AA revision chips on Relax Kit for 5V Shields and
Relax Lite Kit.
Change-Id: I17d4479657bad0516d4c10c2ad7e745d59e678b7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3136
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The cache is forced to zero to match the value expected by the DPIDR read
so the connect sequence is not destroyed by a SELECT update.
However, DPIDR and in fact all registers except address 4 are independent
of the current DPBANKSEL value. Change swd_queue_dp_bankselect() to use
this fact and avoid touching SELECT for those registers.
Change-Id: I0cd11925fb6adef481bbf45cc24ea2c6dab4b6fb
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3231
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Investigation:
- mem_ap_read_buf_u32() no longer exists.
- JTAG_DP_DPACC & JTAG_DP_APACC are defined in adi_v5_jtag.c now.
Change-Id: I136fc3f389a5a4eb9b68bc759ce653b6da7fa75e
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3243
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
FTFx flash controller requires MCU in normal RUN mode.
Flash cannot be erased, programmed or blank checked in VLPR or HSRUN
modes.
VLPR mode is switched to RUN mode as it does not require any changes
in clock generator setting. VLPR can be active from reset on some
KLx devices (with some FOPT setting) so 'reset init' might not be
sufficient to get device to normal RUN.
Any other mode than RUN or VLPR is reported as an error.
Change-Id: I60f494ce0d534b04870c6219d9b05f66f7244433
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3012
Tested-by: jenkins
Command for partitioning FlexNVM to data flash and EEPROM blocks
Change-Id: Ia0ea65d72b0e5f23da330520284b0bd26435e444
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2991
Tested-by: jenkins
FlexRAM should be requested before any section programming.
Test FCNFG RAMRDY bit before issuing FTFx_CMD_SETFLEXRAM
to speed up operation and to cover pflash only devices.
Change-Id: Ib0f2d8e8ab8b1507cbf2b7f8565178ab79941f5d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2990
Tested-by: jenkins
kinetis_ftfx_command() did not use other struct flash_bank* members
than base->target. Switching first parameter to struct target*
enables use of kinetis_ftfx_command() without unnecessary bank
getting and probing.
Removed kinetis_securing_test: kind of dead code, same function
as command flash erase_address pad 0x400 0x10
Removed "NAND" word from help as flash is obviously NOR
Change-Id: I3f5fc295ef2bf42f3e913549949f2a36377f6367
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2988
Tested-by: jenkins
FlexNVM (data flash) is memory mapped at 0x10000000.
Driver used to send the same address to FTFx controller for erase/write ops.
This was wrong as FTFx accepts only low 24 bits of address.
To fix addressing for flash controller kinfo->prog_base was introduced.
Added FlexNVM protection check, blank check and data flash size calculation.
Blank check cannot use block operation on FlexNVM when EEPROM backup is enabled.
Removed non functional reassign logic and bank_ordinal stuff.
Now one can re-probe FlexNVM banks after nvm_partition change.
Change-Id: Ia60b938266963e5d056701278cdf7bf2f62a429a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2987
Tested-by: jenkins
This patch also addresses a problem with devices where no serial
number is available. For further details, see:
http://repo.or.cz/libjaylink.git/commit/7e0508d8487f65f71411117dff2e0b093e00bc80
Such devices are now ignored if device selection via serial number is
used.
Nevertheless, these devices are still usable by using the USB address
for device selection or just by omitting device selection. The latter
one is only possible if only one device is connected.
Change-Id: I5763db25e97ba3d924cb642da7e64e951e09ecb7
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3225
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Check CMSIS-DAP adapter has serialnumber before pass it to wcscmp.
Keep looking for onother adapter if choosed one doesn't have correct
serialnumber.
Change-Id: I7d386a03cb49b9baf22073ae1c6b14269ed3b618
Signed-off-by: Andrii Anpilogov <anpilog@gmail.com>
Reviewed-on: http://openocd.zylin.com/3226
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is for targets where flash controller has reverse endianness
compared to target. For these, the 'bus_swap' parameter can be given to the
CFI driver, which will cause command CFI commands to be written with
bytes swapped. This is only for x16 CFI flash.
Change-Id: I698b768e92e65d160232e90b0e81a824e3c81a46
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3041
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to signal propagation delays, sampling TDO on rising TCK can become
quite peculiar at fast TCK rates. However, FTDI chips offer a possiblity
to sample TDO on falling edge. With this change, stable operation can be
achieved at 30MHz clock even over 10cm ribbon cable.
Change-Id: Icaf240535dae15512e3c60a944e22a5fbc1b0b06
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3180
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add support for the Intel Quark mcu D2000 using the new quark_d2xx
target.
Changes to the lakemont part are needed for the D2000 core and
backwards compatible with the X1000 one.
Change-Id: I6e1ef5a5d116344942f08e413965abd3945235fa
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3199
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
duration_elapsed and duration_kbps will not modify the struct duration
passed as function argument, hence it should be declared const.
Change-Id: I459c396952c78e907257e2c2f2c630abde92aaa8
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit 830d0c55c0 introduced
a regression in error recovery after reconnect:
If first SWD queue run in dap_dp_init() fails, DP_SELECT
does not get reset.
Change-Id: I947e2afe9933e4645a6141ece7816af8e6082cf2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3194
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit fd43be0726 introduced a
regression: since the register names were changed from those
traditional for MIPS to common GDB scheme the code that makes use of
them needs to be changed accordingly.
This commit restores pic32mx flash driver functionality.
Change-Id: Id18c739390fae36737a02dc30c363d0444f53b96
Reported-by: Louis Rannou <louson@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3206
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
niietcm4_write() buffer padding:
add correct buffer padding for 16 bytes.
Args check in FLASH_BANK_COMMAND_HANDLER():
first version of the driver had 7 args, current - 6. This patch will fix
error when flash is rejected (current k1921vk01t.cfg has flash bank init
with 6 args).
Timeouts in flash flag checking procedure:
increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check()
cause there were problems in some hardware configurations.
JTAG ID:
wrong id in k1921vk01t.cfg replaced with right one.
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Change-Id: I84296ba3eb4eeda4d4a68b18c94666f1269a500f
Reviewed-on: http://openocd.zylin.com/3171
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use it to print the manufacturer of detected TAPs
Change-Id: Ic4384c61c7f6f7ae2a9b860a805a5997542f72cc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3177
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
dap_sync() executes all commands in the JTAG queue and then checks
if a WAIT condition happened inside the last batch. If yes, a recovery
is invoked. If not, processing continues without checking for
errors. This function should be called in long AP read or writes, e.g.
while uploading a new application binary, at intermediate points within
the transfer where the cost of flushing the JTAG queue and checking the
journal doesn't affect performance too much.
Change-Id: I99eeaf47cdf951e15e589a04e74b90b5ce911386
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3181
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ADIv5 specifies that DP and AP accesses may generate a WAIT
response when the hardware is not able to complete a request for various
reasons in time before the next request is sent. Currently, the software
treats a WAIT response as a fatal error and aborts operation on the DAP.
This patch implements WAIT handling by keeping a journal of all
outstanding and completed accesses, including their response status.
At certain times (when dap_run() is called), the journal is inspected
for WAIT responses and all discarded accesses are replayed to complete
them. Special care is taken to not re-execute already successfully
completed operations.
Change-Id: I2790070388cf1ab2e8c9a042d74eb3ef776aa583
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3166
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Make the J-Link driver handle everything needed for FPGA programming,
this includes arbitrary long scans and STABLECLOCKS command.
Also, bump to the latest upstream libjaylink to properly support this.
This code is heavily inspired by Andreas Fritiofson's ftdi.c.
Change-Id: Ic5fd87aa88b58ff1138dc2e0a197bb52321b1541
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2946
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
BeagleBone debian 7 builds produce:
jlink.c: In function 'jlink_speed':
jlink.c:218:11: error: declaration of 'div' shadows a global declaration [-Werror=shadow]
jlink.c: In function 'check_trace_freq':
jlink.c:1065:54: error: declaration of 'div' shadows a global declaration [-Werror=shadow]
jlink.c: In function 'config_trace':
jlink.c:1101:11: error: declaration of 'div' shadows a global declaration [-Werror=shadow]
Fix this by changing the local variable to 'divider'.
Change-Id: I96a0cc0f7d4d4af5a56aa1e918e5416d3c61cbfe
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3185
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
BeagleBone debian 7 builds produce:
adi_v5_jtag.c: In function 'jtag_ap_q_bankselect':
adi_v5_jtag.c:336:11: error: declaration of 'select' shadows a global declaration [-Werror=shadow]
Fix this by changing the local variable to 'sel'.
Change-Id: I8e29662ac12bc77d38d5064046d59b7364853cd9
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3184
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The existing arm_adi_v5.c code decodes CoreSight peripherals based
on the part number field. However, these are specific to a
particular manufacturer (often ARM). The same part number from
two different manufacturers (distinct designer ids) should not
decode as the same CoreSight peripheral.
The Analog Devices ADSP-SC58x and ADSP-BF70x have peripherals that
overlap with existing OpenOCD decoding. The part number is the
same as existing OpenOCD decoding, but have a different JEP106 code.
Most, if not all, of the existing part number entries in
arm_adi_v5.c are probably specific to ARM. Change all entries
suspected to be designed by ARM to match only ARM's designer ID.
However, to preserve legacy behavior, existing non-ARM entries are
encoded with a wildcard so that they will behave in the same way as
the existing legacy code. It is desirable, however, to start
encoding the data with designer codes to avoid such ambiguity.
Revising the code to check both the part number and designer id
seemed to a warrant a const array lookup table instead of a
multi-tiered switch statement.
Also try to sync part identification IDs with relevant ARM docs.
Change-Id: Iac1374e4cfc6f04cebb479c0e3fa9bde527cc4a3
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
[andreas.fritiofson@gmail.com: change JEP106 to designer ID, cleanup]
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3128
Tested-by: jenkins
The HLA target shares an examine handler with cortex_m but since it
lacks direct access to DAP, some operations need to be omitted.
Change-Id: Ifdd9d3da4a3a3c2e1c9721284b21d041b3ccaa7a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3183
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
work around issues with software breakpoints when the text segment
is mapped read-only by the OS. Set DACR to "all-manager" to bypass
TLB permission checks on memory access.
Change-Id: I79fd9b32b04a4d538d489896470ee30b26b72b30
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3107
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change tests when reading from 'value' in sysfs from =='0' to !='1'.
This guards against broken sysfs GPIO implementations that return
non-zero for high rather than just '1' while still being clean and
correct code. Note that sysfs will never output a leading zero even
in a very broken implementation as that is covered in gpiolib.c, not
the offending driver.
Tested against broken Freescale kernel 3.14.38 on i.MX6SL.
Change-Id: Id05567bb8504b1babef33d6ee5172bceefeca8b8
Signed-off-by: Matthew Campbell <mcampbell@izotope.com>
Reviewed-on: http://openocd.zylin.com/3121
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On JTAG, all reads are pipelined. If you read a register, the result is not
delivered inside the request that issued the read, it is delivered in the
following request. The current code therefore issues a scan of the RDBUFF
register after each read. This adds a superfluous transaction after each
read.
This patch follows a strategy similar to what SWD already implements.
It also leverages that all JTAG reads are pipelined, i.e. the result
will be clocked out in the next JTAG data phase, no matter if it's
READ or WRITE. Therefore it's never necessary to explicitly read RDBUFF
other than for the very last READ before a dap_run().
Change-Id: Ie40b1fef3203f0cdcb503f40dcbd2a68b0f9776c
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3167
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Debug initialization blindly selects AP#0 as default, which is the AHB-AP
in many cases. This sets the default for target_read/write functions.
However, AHB-AP is the wrong choice, because it bypasses caches on read
and write and also makes some peripherals inaccessible (e.g. l2 outer
caches). This patch explicitely selects the APB-AP (debug_ap) as the
default.
Change-Id: I13f9e0750186d35dcfc135c8d67d437c5884d9c4
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3113
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove entirely the concept of a "selected" AP that has to be maintained
between calls. All the information the DAP ops need are now provided to
each call through the AP/DAP pointer.
Consolidate the cache of the SELECT fields into one single field caching
the entire register.
Change-Id: I2e1c93ac5ee8ac38a7d680ca2c660c30093a6b87
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3165
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Move the mandatory dap_ap_select() call into the dap_queue_ap_read/write
wrapper.
This avoids the need for dap_ap_select() and the notion of a "current" AP
within target code.
Change-Id: I5cde8f3eef2c662f7458be6f3b3dd44ea693bd74
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3164
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Make dap apsel without arguments show current state instead of changing
to AP 0.
Change-Id: I75ea10e3e1b8a067f2dc417ec6691dc7ceec1af6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3163
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All AP operations should select the AP to use before calling it so
there's no point in restoring the previous value afterwards.
The explicit call to dap_ap_select() before all AP operations should be
moved into dap_queue_ap_read/write() which then would have to take the
AP as an argument instead of the DAP.
Change-Id: Icacb0c76ef2a5ac36b4d2f26b52ec01a8850286e
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3156
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
It's currently set during target creation but the AP that will be used
for the target is not even known.
Change-Id: I4502e7eb1fa8d90f746445b8cf8a4c21cb7d519e
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3155
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The AP for which the TAR/CSW is printed may not be the one that caused
the failure. Remove the flawed output entirely. The correct info is
printed in mem_ap_read/write anyway.
Change-Id: I97580a0662dcf02e80646e45445cdbfc251122d8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3154
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All mem_ap_* functions now make sure the SELECT register is updated with
the AP number that it's operating on. This shouldn't have to be handled
explicitly.
Change-Id: Ib193d8930fabb6a25715064355f98258c9580b5d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function does two separate things, powering up the DP and setting
up a MEM-AP. But the DP needs to be powered before even searching for a
MEM-AP to initialize and targets may have multiple MEM-APs that need
initializing.
Split the function into dap_dp_init() and mem_ap_init() and change all
call sites to use the appropriate one.
Change-Id: I92f55e09754a93f3f01dd8e5aa1ffdf60c856126
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3151
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reduce use of magic numbers and add AXI type MEM-AP detection. Don't try
to call dap_rom_display on a non-existent AP.
AP identification is unique per designer, so make sure the JEDEC code
matches ARM when interpreting the AP type.
Change-Id: I8e86b7de61811382afe99bf15094ab71b43f5fdf
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3150
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change the debug_ap and memory_ap fields of the cortex_a target and
the debug_ap field of the cortex_m target to be pointers to the
struct adiv5_ap instead of AP numbers in some known DAP.
This reduces the dependency on the DAP struct in the targets and
enables MEM-AP accesses to take the relevant AP as parameter.
Change-Id: I39d7b134d78000564b7eec5bff464adf0ef89147
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3147
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This required fixing the AP ID parsing in dap_find_ap() to
match IHI0031C. The AXI type was added too.
Change-Id: I44577a7848df37586e650dce0fb57ac26f5f858c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3146
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This will make it possible to reference directly the AP used for debug
in the target instance and remove the DAP reference. This will in turn
enable getting rid of the need to select an "active" AP in the DAP (using
dap apsel).
Change-Id: I265846a427c714204f4fd3df3cdb75843686c2d0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3144
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Not clear what it was supposed to be used for. It probably shouldn't.
Change-Id: Ife1d833e59ba80f93876447d752a0ca7e7b57b0f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3143
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Cortex-A and Cortex-M keeps an arm_jtag struct around just to be
able to pass a pointer to it to one common JTAG function which anyway
only uses the TAP field.
Refactor the function to take a TAP directly, remove the legacy struct
from cortex instances and store the TAP pointer only in the DAP.
Cortex-M makes a call to arm_jtag_setup_connection() with the struct
but the function does nothing useful for a Cortex-M target so remove
the call.
Change-Id: I3b33709ef55372ef14522ed4337e9f2e817ae3ab
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Making the SWD driver aware of the DAP that controls it is a layering
violation.
The only usage for the DAP pointer is to store the number of idle cycles
the AP may need to avoid WAITs. Replace the DAP pointer with a cycle
count hint instead to avoid future misuse.
Change-Id: I3e64e11a43ba2396bd646a4cf8f9bc331805d802
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3141
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Separate out the values from adiv5_dap that are associated with a specific AP into a new struct, so we can properly support multiple APs. Remove the DAP struct from the armv7* structs, because we can have multiple CPUs per DAP, and we shouldn't have multiple DAP structs. Tidy up a few places where ap_current is used incorrectly.
Change-Id: I0c6ef4b49cc86b140366347aaf9b76c07cbab0a8
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2984
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Prepare to support multiple cortex-m cores on one DAP. Uses mem_ap_sel_*
functions and removes mem_ap_* functions. Adds a new debug_ap
parameter to the cortex_m (currently set to zero as in existing code).
Change-Id: I6926029d1e7bf44a42d453d1aff349bda824ba72
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2983
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
ERROR_WAIT is better than ERROR_FAIL in timeout condition.
Change-Id: Iefe837f276a9091ce6c18db5947212c449f49d89
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2934
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is a TODO in the src/target/arm_adi_v5.h for MEM-AP registers.
Some new registers are introduced in ADIv5.2 specification.
MEM_AP_REG_MGT (0x20) // Memory Barrier Transfer register
MEM_AP_REG_TAR64 (0x08) // Bits[63:32] of Transfer Address
MEM_AP_REG_BASE64 (0xF0) // Bits[63:32] of Debug Base Address
Refer to
7.5 MEM-AP register summary in
IHI0031C: ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
Change-Id: I3bc4296a04c35f5c64f851e5865d3099922613fa
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2904
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem
No matter what target->coreid is, it always shows
Detected core 0 dbgbase: ...
In dap_lookup_cs_component(), it decreases the core index value to zero
in order to find the desired core.
The reference to coreidx is necessary considering "a device which has nested
ROM tables, with each core described in its own table." (by Paul Fertser).
Change-Id: I9b56d45d6edf6639e748a625ab27787f8e5a5776
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2902
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
They are only used to initialize the flash bank sectors and never modified.
Explicitly specify the array length while at it.
Cleanup before adding XMC4800 support.
Change-Id: I2985b9a9946b67798dbfd47d8b219d93a7ffc3da
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3131
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
cortex_a_read_apb_ab_memory_fast() uses the wrong order of ITR and DSCR
writes when setting up the transfer. ARM DDI0406C says in C8.2 regarding
"Fast mode" operation to first switch to fast mode and then latch the
instruction in ITR. Current implementation first wrote ITR, causing
the instruction to be executed immediately, then switched to fast mode
without an instruction latched. Repeated reading of DTRTX didn't
execute LDC and thus replicated its current content into the whole buffer.
This patch uses the following, revised algorithm:
1) switch to non-blocking mode and issue the LDC for the first word
2) if more than one word is to be read:
- switch to fast mode
- latch the LDC instruction into ITR (it is _not_ executed)
- issue (count-1) reads of DTRTX register, each read returns the current
content of DTRTX and re-issues the latched instruction
-> now the second-to-last word is in the buffer and the LDC for the last
word has been issued.
3) wait for the last instruction to complete
4) switch back to non-blocking mode
5) Read DTRTX for the last (or: only) word and put it into the buffer
Change-Id: I44f5c585962ffa5af257c3d5a2a802c122b6b1e4
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3122
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When accessing memory through the ARM core, privilege levels and mmu
access permissions observed. Thus it depends on the current mode of the
ARM core whether an access is possible or not. the ARM in USR mode can
not access memory mapped to a higher privilege level. This means, if the
ARM core is halted while executing at PL0, the debugger would be
prevented from setting a breakpoint at an address with a higher privilege
level, e.g. in the OS kernel. This is not desirable.
cortex_a_check_address() tried to work around this by predicting if an
access would fail and switched the ARM core to SVC mode. However, the
prediction was based on hardcoded address ranges and only worked for
Linux and a 3G/1G user/kernel space split.
This patch changes the policy to always switch to SVC mode for memory
accesses. It introduces two functions cortex_a_prep_memaccess() and
cortex_a_post_memaccess() which bracket memory reads and writes. These
function encapsulate all actions necessary for preparation and cleanup.
Change-Id: I4ccdb5fd17eadeb2b66ae28caaf0ccd2d014eaa9
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3119
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
when disabling the mmu to access physical addresses, normally the d-cache
must be disabled as well. Disabling the d-cache also requires a full
clean&invalidate. However, since all memory writes are treated as write-
through no-allocate and memory reads do not allocate cache lines,
effectively the d-cache state does not change at all. We can therefore
save the the d-cache disabling and flushing.
This patch also simplifies the function a bit.
Change-Id: Ia17c56a28f432156429cd4596107e3652b788e63
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3114
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
for minimal impact on the hardware state, force all memory accesses to
bypass the caches and tlbs. This may actually be the default, but ARM
recommends in DDI0406C to set proper default values on debug init.
Change-Id: If5ac097b6ee725c047b1e86c2f90eabe16b98c7b
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3079
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Other cache functions use an updated pattern for the address range loop.
Bring dcache clean and flush functions in line.
Change-Id: Iccb4a05c49054471033a3403363110cb08245d5b
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3035
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Call armv7a_l1_d_cache_flush_virt() before writing the breakpoint,
to make sure the d-cache is clean and invalid at the breakpoint
location down to PoC.
Call armv7a_l1_d_cache_inval_virt() after writing the breakpoint
again, so that d-cache will pick up the modified code.
Call armv7a_l1_i_cache_inval_virt() after writing the breakpoint
to memory to make the change visible to the CPU.
Change-Id: I24fc27058d99cb00d7f6002ccb623cab66b0d234
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3033
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
D-Cache invalidate is a dangerous operation. It will only work correctly
if full cache lines are invalidated. When partial cache lines are
invalidated, i.e. the target address range does not start and end
at a cache line boundary, cpu data writes outside of the target range
will be dropped. This patch adds special treatment for partial cache
lines by doing a clean & invalidate on the partial lines before
invalidating the rest of the range.
Change-Id: I64099ddb058638e990a7eb0ee911b9cc8f6f8901
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The following changes are implemented:
- Clean&Invalidate the VA range to PoC *before* the write takes place
- Remove SMP handling since DCCIMVA instruction already maintains SMP
coherence.
- Remove separate Invalidate step
Change-Id: I19fd3cc226d8ecf2937276fc63258b6a26e369a7
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3027
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This patch adds a function for cleaning & invalidating a virtual
address range from the architecture caches down to the point of
coherence.
Change-Id: I4061ab023a3797fabc967f3a34498034841d52c6
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3026
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
There's only one function left that handles cache info display,
no need any more for a function pointer and runtime initialization.
Change-Id: I90b09577f81607917b11f0ab5600a0e2dce223e2
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3025
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
ARMv7 architecture allows up to 7 cache levels that are architecturally
visible, as opposed to "system caches", which are outside of the domain
defined by ARMv7 and require separate management. This patch enables
detection and identification of caches at all levels. It also implements
a new "flush-all" function that cleans & invalidates all cache levels to
the "Point of Coherence".
Change-Id: Ib77115d6044d39845907941c6f031e208f6e0aa5
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3024
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This patch is on the path to unified handlers for both inner and
outer caches. It removes the special overrides installed when
an outer cache is configured.
Change-Id: I747f2762c6c8c76c700341cbf6cf500ff2a51476
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3022
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The outer cache is not necessarily at L2 in a system. Rename functions
to make that clear.
Change-Id: Ia636a4844f50634f2bdf5cdce285febc1a47c11f
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3020
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch introduces, new command set and handlers for l1 and l2x caches.
Patch set 10 folded the following changes into this one:
Ib1a2a1fc1b929dc49532ac13a78e8eb796ab4415
If8d87a03281d0f4ad402909998e7834eb4837e79
I0749f129fa74e04f4e9c20d143a744f09ef750d8
Change-Id: I849f4d1f20610087885eeddefa81d976f77cf199
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/2800
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This was needed for ahb access
Change-Id: I638f45a276a593c08140b5d9d7480617aa85f096
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2796
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Problem
dap->ap_current is register value, not field value.
it restores invalid ap when it calls dap_ap_select(dap, ap_old) later.
* assume the current ap is 1, dap->ap_current value would be (1 << 24).
ap_old = dap->ap_current; <-- ap_old = 1<<24 = 0x1000000.
...
dap_ap_select(dap, ap_old); <-- select 0x1000000, not 1.
* All AP registers accessing fail afterwards.
One of the reproducible case(s): CORE residents in AP >= 1
dap_lookup_cs_component() being used to find PE(*).
In most cases, PE would be found in AP==0, hence the problem is hidden.
When AP number is 1, dap->ap_current would have the value of 1<<24.
Anyone get the AP value with dap->ap_current and resotre it later would
select the wrong AP and all accessing later would fail.
The ARM Versatile and/or FPGA would have better chance to provide this
kind of environment that PE residents in AP>=1. As they have an 'umbrella'
system at AP0, and main system at AP>=1.
* PE: Processing Element. AKA Core. See ARM Glossary at
http://infocenter.arm.com/help/topic/com.arm.doc.aeg0014g/ABCDEFGH.html
Fix
Use dap_ap_get_select() to get ap value.
a. Retrieve current ap value by calling dap_ap_get_select();
src/flash/nor/kinetis.c
src/target/arm_adi_v5.c
b. The code is correct (dap->ap_current >> 24), but it's better to use
dap_ap_get_select() so everything could be synchronized.
src/flash/nor/sim3x.c
Change-Id: I97b5a13a3fc5506cf287e299c6c35699374de74f
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2935
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If supported, the maximum transport speed is now retrieved from the
device.
Change-Id: I614f405ec91cf199c851781785fd26cbd10c37a6
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2955
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch uses libjaylink which is a library to access J-Link
devices. As other tools which are not in the scope of OpenOCD also
need to access J-Link devices a library is used. A firmware upgrade
tool and an advanced configuration tool for J-Link devices are under
development.
Further versions of libjaylink will support additional features
OpenOCD could benefit from. This includes TCP/IP as additional
possibility to connect to J-Link devices as well as power tracing and
device internal communication. The latter is used to access
peripherals on some development boards (e.g EFM32 STK and DVK).
Integration of libjaylink is realized with a git submodule like
jimtcl. As libjaylink depends on libusb-1.0 only, no additional
dependency is introduced for OpenOCD.
All low-level JTAG and SWD implementations of the current driver are
left untouched and therefore no incompabilities are to be expected.
Improvements of this patch:
* Support for more USB Product IDs, including those with the new
scheme (0x10xx). The corresponding udev rules are also updated.
* Device selection with serial number and USB address.
* Adaptive clocking is now correctly implemented and only usable for
devices with the corresponding capability.
* The target power supply can now be switched without the need for
changing configuration and power cycling the device.
* Device configuration is more restrictive and only allowed if the
required capabilities are available.
* Device configuration now shows the changes between the current
configuration of the device and the values that will be applied.
* Device configuration is verified after it is written to the device
exactly as the vendor software does.
* Connection registration is now handled properly and checks if the
maximum number of connections on a device is reached. This is also
necessary for devices which are attached via USB to OpenOCD as
some device models also support connections on TCP/IP.
* Serial Wire Output (SWO) can now be captured. This feature is not
documented by SEGGER however it is completely supported by
libjaylink.
This patch and libjaylink were tested on Ubuntu 14.04 (i386),
Debian 7 (amd64), FreeBSD 10.0 (amd64) and Windows XP SP3 (32-bit)
with the following device and target configurations:
* JTAG: J-Link v8.0, v9.0 and v9.3 with AT91SAM7S256
* SWD: SiLabs EFM32 STK 3700 (EFM32GG990F1024)
* SWD: J-Link v8.0, v9.0 and v9.3 with EFM32GG990F1024
* SWD: XMC 2Go (XMC1100)
* SWD: XMC1100 Boot Kit (XMC1100)
* SWD: IAR Systems / Olimex Eval Board (LPC1343F)
* SWD: Nordic Semiconductor nRF51 Dongle (nRF51422)
* SWD: SiLabs EZR32 WSTK 6220A (EZR32WG330FG60G)
Except for Windows XP all builds are tested with Clang in addition to
GCC. This patch and libjaylink are not tested on OSX yet.
Change-Id: I8476c57d37c6091c4b892b183da682c548ca1786
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2598
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
http://support.code-red-tech.com/CodeRedWiki/DebugAccessChip
> Note that once you have recovered debug access to your MCU, then in most cases you should then modify your Debug Configuration to turn vector catch off again. If this is not done, then this can cause problems in some circumstances with some versions of the Code Red IDE. For example with NXP LPC13xx parts, connecting more than once to the MCU with vector catch enabled can lead to the part ID being incorrectly read - which can again cause debug connections to fail
This patch adds an alternative part ID for LPC1343. With this patch "program" command works fine for flashing.
Change-Id: I8632e898a4c33102455925d25715b4f4edfa1d97
Signed-off-by: Jakub Kubiak <jakub@kubiak.es>
Reviewed-on: http://openocd.zylin.com/2782
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This adds docs, example config, flash driver.
Driver is only supports K1921VK01T model for now.
Change-Id: I135259bb055dd2df1a17de99f066e2b24eae1b0f
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Reviewed-on: http://openocd.zylin.com/3011
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The probe and info methods had duplicate sections decoding family names
to generate a human friendly part name. Extract this to a common
helper.
Change-Id: I4c6309d83c601e154b7c14ad9c15c53854ee1e98
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2932
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Basic basic support to get running, magic numbers taken from revision
0.90 of the reference manual.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Change-Id: Iff6ab94d30698f056ef09f7a856b7285fed8f441
Reviewed-on: http://openocd.zylin.com/2931
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By saving a pointer to the tail of the list,
we don't need to traverse the entire command
queue before we're able to append an item to
it.
With this patch, I see a 10% improvement when
using the embedded XDS100v2 on AM437x IDK board
to load a 4MiB binary (linux zImage) to DDR
with load_image.
IOW, we went from ~305kB/sec to ~336kb/sec.
Change-Id: Idb55d49f0d0106043374ab520b2f3b6b32f2c50f
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2709
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Daniele Emancipato <daniele12457@hotmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The svf_progress_enabled variable is global, hence its lifetime is not
limited and it retains the value from the previous run. Fix this by
explicit assignment.
Change-Id: Id6f4fa88f39521606342a37f6876a0948ac5406e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3111
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This makes SVF error output match actual line numbers in the file
processed.
Change-Id: I1fa4b9d0891e4358b7beada516945d5331ebe182
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2945
Tested-by: jenkins
Kinetis driver checks MDM STAT register to detect secured state of MCU.
An unsecured clean device typically triggered a huge fat alarm message.
Now when driver detects secured state it tries to halt MCU and then
re-reads status register.
Command "mdm mass_erase" used to deassert reset when finished
and MCU started looping in hard fault - WDOG reset cycle.
Now "reset halt" is issued. Clean flash is not run after mass_erase.
Change-Id: I23f393509fbd8751d44ffc744ff2d67f1074f74e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3010
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
SAMD driver suffered from following problems:
1) Flash was erased as an integral part of flash write.
It was not documented so with usual workflow it resulted
in erasing flash twice (and reducing flash lifespan)
and in almost double flashing time.
2) Sector erase was silently skipped if "is_erased" flag was set.
"is_erased" logic was not reliable, e.g. when a row write
was aborted after successful write of some pages, sector was
still considered as erased. "is_erased" flag could not
cope with flash writes from a user program.
3) Writing of a block with start address unaligned to a flash page
resulted in failed assert and OpenOCD abort.
4) Disabling cache in bit 18 of 16-bit halfword never worked.
MCU implements cache invalidate in hardware so there is no need
to take care about. This bug was reported by Tony DiCola.
New code does not erase flash in write operation.
Instead it traditionally relies on erasing flash beforehand.
"is_erased" logic and cache disabling is completely removed.
It simplifies write procedure a lot and flash write is now faster.
The change partly solves ticket #109 SAMD/SAM4L driver doubles flash erase.
Change-Id: I582b497d01a351575533a1f8c9810a4413be0216
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3045
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds support for the Atmel SAML21 variant B parts.
There is minimal change between the two variants, but in
variant B the automatic page write which the at91samd flash
driver relies on to be enabled is disabled by default.
With this patch the write row function will now issue a page write
command after each of the four pages in the row if the MANW (manual
write) bit is set. This also fixes flash write for the SAMC20/SAMC21
devices which have the MANW bit set by default as well.
I have also moved the device ID (DID) register bitfield extraction
from the find_part into helper macros. These can be used in the future
if there are more workarounds for specific devices.
Tested (programming) on:
ATSAML21-XPRO
ATSAML21-XPRO-B
SAMC21 Xplained Pro
SAMD21 Xplained Pro
SAMD20 Xplained Pro
Change-Id: I401a8aa1efd64730840c0d62cf49a1e880ea5900
Signed-off-by: Andreas Loehre <alohre@gmail.com>
Reviewed-on: http://openocd.zylin.com/2903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cmsis-dap protocol has both DAP_Connect and DAP_Disconnect commands.
Logically if cmsis_dap_swd_switch_seq() calls DAP_Connect in connected
state it should call DAP_Disconnect first.
Doing so surprisingly solves problems on Atmel EDBG with target SAMD/R/L/C.
Without this change SWD communication breaks after reset run/halt
in config "reset_config srst_only" and reconnect trials repeatedly
fail with "SWD ack not OK: 0 JUNK"
Change-Id: Ie951098d5e0c83f388e2df414608aaabec2135c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to Infineon, XMC4500 EES AA13 with date codes before GE212 -
as seen on an XMC4500 General App Kit - had a zero SCU_IDCHIP register.
Handle this by extending our checks to not error out on zero SCU_IDCHIP
and by printing a useful info string in that case.
Change-Id: Ic2d641a314627dd5a1ff775a0113999191b95e3d
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2751
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 68101e67ac introduced a
regression which resulted for ever-growing registers list (as output
by "reg" command), its contents were doubled every reset (actually,
every examination).
Change-Id: Ie3409c795160a2fc840a5e8a892928df0bcc0c57
Reported-by: Daniele Emancipato <daniele12457@hotmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3100
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch brings the calculation of the address ranges handled by
ttbr0 and ttbr1 registers in line with ARM DDI 0406C, Table B3-1
Change-Id: Ib807c4b1cb328a6f661e1a0898e744e60d3eccac
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3006
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If ttbcr is changed after the debugger has examined a target for the
first time, address translations may fail. This problem does not show up
with Linux because it doesn't use ttbr1, but it shows with other OS that
use this feature. If the debugger connects to the target while it's in
u-boot, all address translations will fail after the OS has booted and
the target can not be debugged.
This patch reads the ttbcr in armv7a_mmu_translate_va() and compares it
a cached value. If a difference is detected, armv7a_read_ttbcr() is called
to re-parse the ttb configuration and update the cache.
Change-Id: I1c3adf53ea9d748a0e1e3091d9581e5c43ed64e8
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3005
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
kinetis_write() with byte count not divisible by prog_section_chunk_bytes
computed wrong wc and therefore paded section chunk by some
random data instead of 0xff
Change-Id: Ic7c66d8a3ceacda9e611e98b9fbf943b8001774b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2994
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Kx devices with FTFA flash need the watchdog disabled when programming.
I tried to keep overhead as small as possible and re-use registers that
were already inquired (e.g. sim_sdid).
Change-Id: Ibc29a26ec34102d78a6c3920dd16f63e134a8f6f
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2986
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This makes it easier to relocate the install tree of OpenOCD from where
it was originally built (for example, if put onto a different machine),
without having to change scripts or add something to the command line
every time.
Change-Id: Ia5edf0eba166f7a999f267bd6a92402dab9b399e
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3004
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The memory leak occurs when opening a file fails. It can be
reproduced by using the "flash verify_bank" command with a filename
that does not exist.
Change-Id: I60b7b545c18793d750ff75d08124fde3f0aa6f64
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2998
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If we work on smp system, the output of step command will depend
on Id of default target.
This patch adds additional information to help find what on which
core is happening.
Example of LOG after this patch.
imx6.cpu.1: target state: halted
^^^^^^^^^^
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x60000093 pc: 0x80076c0c
MMU: enabled, D-Cache: enabled, I-Cache: enabled
imx6.cpu.0: target state: halted
^^^^^^^^^^
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x20000193 pc: 0x802ccb6c
MMU: enabled, D-Cache: enabled, I-Cache: enabled
Change-Id: I536a2cce33b5ab10af9de2a43b9960320c17729f
Signed-off-by: Oleksij Rempel <external.Oleksij.Rempel@de.bosch.com>
Reviewed-on: http://openocd.zylin.com/2691
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A segmentation fault in cortex_m_endreset_event() is sometimes raised
with very broken target like Kinetis Kx with erased flash and active WDOG.
Debugging revealed that cortex_m->dwt_num_comp is 4 and
dwt_list is NULL at cortex_m:290
Change-Id: I229c59d6da13d816df513d1dbb19968e4b5951e2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2989
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Memory for the symbol table was allocated by malloc but not initialized other
than with the symbol name. Therefore `address` and `optional` members were
having arbitrary values leading to every symbol being optional most of the
time which messes up RTOS auto-detection. Memory will now be zero-initialized
as in other RTOS implementations.
Change-Id: I6c6e31ec1ef7e043061adf8c695b2139620e005d
Signed-off-by: Daniel Krebs <github@daniel-krebs.net>
Reviewed-on: http://openocd.zylin.com/3017
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
According to "man 2 poll" the correct header to include is poll.h, not
sys/poll.h. Reported by a build against musl.
Change-Id: I5298b49dc947d1a368e423104c0c0c7b9bdd1a10
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2947
Tested-by: jenkins
In the case that the STKALIGN bit is set on Cortex M processors, on
entry to an exception - the processor can store an additional 4 bytes
of padding before regular stacking to achieve 8-byte alignment on
exception entry. In the case that this padding is present, the
processor will set bit (1 << 9) in the stacked xPSR register. Use the
new calculate_process_stack callback to take into account the xPSR
register and use it on the standard Cortex_M3 stacking.
Note: Change #2301 had some misinformation regarding the padding. On
Cortex-M the padding is stored BEFORE stacking so xPSR is always
available at a fixed offset.
Tested on a Cortex-M0+ (Atmel SAMR21) board which has STKALIGN fixed
to a '1' such that this alignment always occurs on non-aligned stacks.
Behavior of xPSR verified via the (bad-sorry) assembly program below by
setting a breakpoint on the SVC_Handler symbol. The first time
SVC_Handler is triggered the stack was 0x20000ff8, the second time
SVC_Handler is triggered the stack was 0x20000ffc. Note that in both
cases the interrupt handler gets 0x20000fd8 for a stack pointer.
GDB exerpt:
Breakpoint 1, 0x000040b6 in Reset_Handler ()
(gdb) hbreak SVC_Handler
Hardware assisted breakpoint 2 at 0x40f8
(gdb) cont
Continuing.
Breakpoint 2, 0x000040f8 in SVC_Handler ()
(gdb) print $msp
$3 = (void *) 0x20000fd8
(gdb) x/9w $msp
0x20000fd8: 0x1 0x2 0x3 0x4
0x20000fe8: 0x88160082 0xa53 0x40ce 0x21000000
0x20000ff8: 0x0
(gdb) cont
Continuing.
Breakpoint 2, 0x000040f8 in SVC_Handler ()
(gdb) print $msp
$4 = (void *) 0x20000fd8
(gdb) x/9w $msp
0x20000fd8: 0x1 0x2 0x3 0x4
0x20000fe8: 0x88160082 0xa53 0x40e8 0x21000200
0x20000ff8: 0x0
Assembly program:
.cpu cortex-m0plus
.fpu softvfp
.thumb
.syntax unified
.section .vectors
@ pvStack:
.word 0x20001000
@ pfnReset_Handler:
.word Reset_Handler + 1
@ pfnNMI_Handler:
.word 0
@ pfnHardFault_Handler:
.word 0
@ pfnReservedM12:
.word 0
@ pfnReservedM11:
.word 0
@ pfnReservedM10:
.word 0
@ pfnReservedM9:
.word 0
@ pfnReservedM8:
.word 0
@ pfnReservedM7:
.word 0
@ pfnReservedM6:
.word 0
@ pfnSVC_Handler:
.word SVC_Handler + 1
.section .text
.global Reset_Handler
Reset_Handler:
cpsie i
ldr r0, .stack_start
ldr r2, .stack_last
eors r1, r1
.loop_clear:
str r1, [r0]
adds r0, r0, #4
cmp r0, r2
bne .loop_clear
subs r2, r2, #4
mov sp, r2
movs r0, #1
movs r1, #2
movs r2, #3
movs r3, #4
svc #0
ldr r0, .stack_start
ldr r2, .stack_last
eors r1, r1
.loop_clear2:
str r1, [r0]
adds r0, r0, #4
cmp r0, r2
bne .loop_clear2
mov sp, r2
movs r0, #1
movs r1, #2
movs r2, #3
movs r3, #4
svc #0
.loop:
b .loop
.align 4
.stack_start:
.word 0x20000f00
.stack_last:
.word 0x20000ffc
@ first call - 0x2000fff8 -- should already be aligned
@ second call - 0x2000fffc -- should hit the alignment code
.global SVC_Handler
SVC_Handler:
bx lr
Change-Id: Id0940e6bbd6a59adee1378c0e86fe86830f0c8fc
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Cc: Evan Hunter <evanhunter920@gmail.com>
Cc: Jon Burgess <jburgess777@gmail.com>
Reviewed-on: http://openocd.zylin.com/3003
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some targets (Cortex M) require more complicated calculations for
turning the stored stack pointer back into a process stack pointer.
For example, the Cortex M stores a bit in the auto-stacked xPSR
indicating that alignment had to be performed and an additional 4
byte padding is present before the exception stacking. This change
only sets up the framework for Cortex-M unstacking and does not
add Cortex-M support.
Note: this also fixes the alignment calculation nearly addressed by
change #2301 entitled rtos/rtos.c: fix stack alignment calculation.
Updated calculation is in rtos_generic_stack_align.
Change-Id: I0f662cad0df81cbe5866219ad0fef980dcb3e44f
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Cc: Evan Hunter <evanhunter920@gmail.com>
Cc: Jon Burgess <jburgess777@gmail.com>
Reviewed-on: http://openocd.zylin.com/3002
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Intel is relicensing our contributions to OpenOCD under GPL
version 2 or any later version. We previously contributed code
under GPL version 2 only. It was not our intention to differ
from the standard OpenOCD license. We're correcting that here.
This also applies retroactively to previous versions of our
contributions to OpenOCD.
Change-Id: I5e831ed95d03d2044d8e5a8375b21c6e52c933d7
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3044
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
K22FN1M0 and K22FX512 has FTFE flash and old style SDID.
K22FN128, 256 and 512 has FTFA flash and new style SDID
K63 and K64 detects as K61 and K62, see Errata 1N83J e7534
Change-Id: I2aca6f1f18819bb2b2ec4982036510de444ad2ac
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2867
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Patrick Stewart <patstew@gmail.com>
max_flash_prog_size euals to pflash_sector_size_bytes for most of devices.
There is no point setting max_flash_prog_size for devices without
FS_PROGRAM_SECTOR capability.
Check for zero sector_size to avoid div by zero exception in case of
device has FlexNVM but the driver does not define nvm_sector_size_bytes
Change-Id: Iaf4e007fb1ec3d24c373350410e4bebe504a4c3e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2958
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Patrick Stewart <patstew@gmail.com>
The K24 uses the KL-style SDID register and has some flashing quirks, so the kinetis driver does not support it properly.
Extend the chip detection routine to support the new SDID format. Add a parameter for the maximum flash size, as the K24 only supports 1k flashing blocks but has 4k sector size. Remove global 'granularity' array, as it's only really needed in one function. Replace 'klxx' with an enum showing which flash commands are actually supported on a given chip.
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Change-Id: Ie244fab564d58c5cfe4fa36a025f0b2674ffad69
Reviewed-on: http://openocd.zylin.com/2864
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I3cf5ced568319878b8bf40743e4c07718f630c68
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2953
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Flash driver "mini51.c" and "nuc1x.c" are same target MCU.
This patch integrates each driver and functions,
and makes into new "NuMicro" flash driver.
Change-Id: Ifff5c1cfdd265acca0f489631695be9194fa144c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A target config and a simple flash driver for the ADuCM360 microcontroller.
The EEPROM of the chip may be erased and programmed.
Change-Id: Ic2bc2f91ec5b6f72e3976dbe18071f461fe503b8
Signed-off-by: Ivan Buliev <i.buliev@mikrosistemi.com>
Reviewed-on: http://openocd.zylin.com/2787
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
The problem was reported by jstefanop on IRC, the SVF was generated with
Xilinx ISE 14.7.
Found and investigated with Valgrind's vgdb service.
Change-Id: I32b0e77e0380ce4a391661f97449f9c2a5f83625
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2933
Tested-by: jenkins
Currently, the maximum size of a command sent to the TCL server is
4k. This patch increases this limit up to 4M.
Reasoning:
To get high-speed JTAG data transfers, I'm using a very long shift
register. This reduces the overhead of the state changes, as well as the
latency due to the common USB adapter transfers considerably. In order
to submit those long DRSCAN commands to OpenOCD over the TCL/TCL
interface, long TCL command lines are required. This is enabled by this
patch.
v3:
Address review comments. Drop line instead of connection when realloc()
fails.
Changes in v2 of this patch:
The line buffer is allocated dynamically to avoid an OpenOCD memory
overhead if the large buffers are not used. The buffer starts at 4K and
increases exponentially up to 1M, and then linearly in 1M increments up
to 4M.
Change-Id: Iecaef6a56ed5e18e9de4d912a514031ea78fa3bd
Signed-off-by: Philipp Wagner <philipp.wagner@tum.de>
Reviewed-on: http://openocd.zylin.com/2837
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add constant CONNECTION_LIMIT_UNLIMITED which indicates a service
has no connection limit
Change-Id: I008d31264010c25fa44ca74eb6d5740eca38bee1
Signed-off-by: Austin Morton <austinpmorton@gmail.com>
Reviewed-on: http://openocd.zylin.com/2937
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Problem
As my compiler has "warnings being treated as errors" on, it shows the
error message:
error: 'retval' may be used uninitialized in this function
Investigation
Nothing wrong with the logic, 'retval' would have a value before returning.
Just wanna get rid of the compiling "warning as error" message.
Solution
Provide a reasonable default value
Change-Id: I712c15f82819c6c48bee9dceca8de4b18aeb29b0
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2905
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
During reallocation a new memory region might be allocated and the old
one freed. If jtag queue is holding a pointer to the old memory, it will
segfault during the execution. Avoid this by flushing the queue before a
reallocation attempt is made.
This should fix ticket #102.
Change-Id: I737fc3f1ebf6d76413a475beb8bf20184fe0233f
Reported-by: Alex Forencich <aforencich@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2899
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the chip IDs corresponding to the new 5V "SAMC" parts which are
otherwise identical to the SAMD and should work with this driver. Also
add the configurations for their Xplained Pro boards.
Change-Id: Ic268d4ac384a3a77d4211a94da9f9faf4d8c0f7b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2809
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes a warning as reported by the current clang version:
../../../../src/flash/nor/sim3x.c:867:20: error: address of array
'sim3x_info->device_package' will always evaluate to 'true' .
Change-Id: Ie160cbe6df8f491e9beff38d47e2f13575529bf9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2838
Tested-by: jenkins
Reviewed-by: Oleksij Rempel
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only read access to flash chips so is through the target's
memory. Flashes like jtagspi do not expose a memory mapped interface
to the flash. These commands use the flash_driver_read() driver API
directly.
Change-Id: I40b910de650114a3f676507f9f059a234377d862
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2842
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds an option to disable the use of the JSTART instruction
when loading bitstreams to xilinx fpgas. JSTART apparently prevents
configuration if the startup clock is not set to the jtag clock in
the bitstream.
xc3sprog is omitting JSTART for all devices. Problems with loading a bitstream
that does not have StartupClk:JTAGClk are described here:
http://www.xilinx.com/support/answers/56151.html
Change-Id: I8137c0bae05a8c3c6f8e2611869f70a770d1651d
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The testee target is usefull for certain non-cpu pass-through
situations, for example in the case of a spi flash mapped to the DR of
a JTAG tap, as is the case for most FPGAs with SPI flashs behind them.
We just manage the RUNNING/RESET/HALTED state in the testee driver to
support it being halted which is a requirement for flash banks.
Change-Id: I1b4d52c58a1f6bd753e126bfde74dcc5164d7b69
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2840
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add USB VID and PID for the J-Link interface running on the Nordic
Semiconductor nRF51-DK. Also tested with debug out port to debug
external boards.
* Elimiantes need for `-c "jlink pid 0x1015"` on the openocd cmd line.
Change-Id: Ib23acb72b9f5183b76fc7dc22b556982869ae830
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Reviewed-on: http://openocd.zylin.com/2775
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ThreadX uses two stacking schemas on ARM926E-JS, extend API to use more then
one stecking at time.
Change-Id: I92d445ad0981b6409ea4c4e7e438d3a7ae39cbe7
Signed-off-by: Alexander Drozdov <adrozdoff@gmail.com>
Reviewed-on: http://openocd.zylin.com/2848
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
MMU types were checking and installing fakes at init, but this wasn't catching
all devices. Fixes segfaults when attempting mdw and friends on avr.
Change-Id: I5b11f9913157a21f1aeb11ec852f593b529d9be8
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2791
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Even though the latest firmware version for stlink-v1 supports "v2"
JTAG API, the hardware SRST handling is still broken; amend the check
accordingly.
Change-Id: I62c662cd7aa209d2d6e9fe260f5c0be81d0ce672
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2761
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the identifiers to support the flash on the Cypress Type-C Port Controller
chips of the CCG1 family : http://www.cypress.com/ccg1/.
Tested successfully on CYPD1132-16SXI.
Change-Id: I3fe6283379e5bcab964afac31b547ef95535aa2c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://openocd.zylin.com/2757
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The notation Gx0 in the nRF51 Series Compatibility Matrix indicates that
the specified HWID is valid only for build code 0 of each chip, and for
subsequent builds the HWID will be different. Replace the Gx0 notation
with G0 throughout, and add the missing HWID for nRF51422 QFAC A1
(present on the newer nRF51 developer boards).
See: https://www.nordicsemi.com/eng/nordic/download_resource/41917/5/55913589
See: https://devzone.nordicsemi.com/question/30774/mapping-hwid-to-revision-information/
Change-Id: I79d842137d41342db35904867c48b06fbc6fbc70
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2593
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since mqx comes last in the list, with the auto option its
update_threads is called even though it wasn't detected.
This check should be removed from all the rtos helpers and moved to
the generic code, but better do it later all in one go.
Change-Id: If24ab42a58a468d90e9f12028d4c2fb76a9bc2e8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2741
Tested-by: jenkins
It was observed on AM437x that after every reset the target's debug
regions are unpowered. To be able to properly communicate with the
target and perform cortex_a init debug access after a reset event the
examination need to be performed every time, not just on OpenOCD
start.
Change-Id: Idf272e127ee88341e806ee00df154eade573451d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2723
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
After intermittent connection failures or target power failures it
might be necessary to try reexamination even when polling fails. This
should make communication with Cortex-A targets more reliable.
This was runtime tested with stlink attached to an stm32l1 and an FTDI JTAG
adapter attached to an stm32f1 target.
Change-Id: I38c4db8124b7f4bbf53ddda53c13273449f49c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2721
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Färber <afaerber@suse.de>
This adds support for the new Atmel SAML21 family of low-power Cortex
M0+ devices. Their Flash controller is essentially the SAMDxx one so
the change consists of adding the new part IDs. Unfortunately the
device ID logic had a couple of mistakes in it that did not affect
anything on SAMD2x devices (due to 0 values expected there) but that is
a problem on L21, it's therefore addressed here and things should now
match the datasheets.
Tested on Amtel SAML21 Xplained Pro development kit against the included
SAML21J18A there. Also tested for regressions on a SAMD20 and SAMD21
using their dev kits.
Change-Id: I768f75e064b8656c15148730dacaa4c3acfc4101
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2690
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the mandatory Info documentation for the driver as well as
the usage field.
As a clean up, this also includes freeing of the allocated memory
which results in a memory leak if probe is invoked multiple times.
Valgrind-tested.
Reported by Dmitry Shpak.
Change-Id: I2b1d9b9e8b069c6665b11d880b40ce19a1b26ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2694
Tested-by: jenkins
Reviewed-by: Дмитрий Шпак <disona@yandex.ru>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch was tested with an EZR32WG Starter Kit.
Change-Id: I0f7c619e715fe30e88e6da3bead0806dd3bce819
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2700
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Run-time tested with FreeRTOS V8.1.2 (current version).
For the time being I propose this way of dealing with RTOSes that do
not export necessary information on their own.
I also suggest implementing a similar scheme for ChibiOS, exporting
the necessary struct fields' offsets via an OpenOCD-specific helper.
Change-Id: Iacf8b88004d62206215fe80011fd7592438446a3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2347
Tested-by: jenkins
xSuspendedTaskList and xTasksWaitingTermination are only available for
some configurations. Missing optional symbols will have their addresses
remaining at zero so the corresponding lists will be skipped when
building the task list.
Change-Id: If330f5038d009298c3a14a4d2756db7105a30bc8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2425
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a remake of http://openocd.zylin.com/1966
originally written by Angus Gratton <gus@projectgus.com>
ATSAM4L has a "System Manager Access Port" (SMAP) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Without this change any use of sysresetreq or srst locks the chip
in reset state until power is cycled.
A new function smap_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and SMAP reset is released then.
Change-Id: Iad736357b0f551725befa2b9e00f3bc54504f3d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2604
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some targets need arbitrary amount of time (usually not too long)
after reset (both sysresetreq and srst) to do initialisation, and
SWD/JTAG is not available during that. According to PSoC4 docs, the
debugger should try connecting until it succeeds.
Also ahbap_debugport_init might be necessary to perform after using
hardware srst too, so add it there (except for the targets that
support srst_nogate since they are very unlikely to need it).
Change-Id: I3598d5ff7b8e0bf3a5566a57dec4b0b2b243d297
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2601
Tested-by: jenkins
In some cases (the most obvious are TI's SoCs) ROM table lacks entries
for the cores, so OpenOCD has no way to determine what debug base to
use. Due to an error fixed in ec9ccaa288 it wasn't handled properly,
and OpenOCD would continue to try using dbgbase = 0, which happened to
work for e.g. AM437x.
This patch adds a clear indication to the user that to access such a
target, dbgbase must be set manually in the config.
Reported by Felipe Balbi on IRC.
Change-Id: Id8533e708f44b76550eb8b659564f5f45717c298
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2603
Tested-by: jenkins
In some circumstances (e.g. inappropriate jtag clock)
target_write_memory in lpc2000_iap_working_area_init might fail. The
allocated working area should be freed inside
lpc2000_iap_working_area_init in this error case.
This was leading to a weird segfault due to stack corruption later
when reset was executed.
Reported by quitte (Jonas Meyer).
Change-Id: Ia2ed42a9970a4d771727fd516a6eea88e9b859e2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2696
Tested-by: jenkins
Calling ahbap_debugport_init() is wrong here because the actions
performed by it might lead to jtagdp_transaction_endcheck errors thus
leading to infinite recursion.
The removed code is not needed now because target polling should lead
to reexamination automatically, and both cortex_a and cortex_m call
ahbap_debugport_init() as part of their target examine handler.
This was reported as a real life issue on IRC by Weaselweb with
Cortex-A target. Quitte reports similar results in some circumstances
(adapter_khz too high) with LPC17xx.
Change-Id: I7148022f76a1272b5262d251f2e807ffb1543547
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2697
Tested-by: jenkins
The IAP working area needs to be freed here, just like in all the
other driver functions since an automatic local variable is used to
store a pointer to it.
This was reported by quitte (Jonas Meyer) on IRC as a strange totally
unrelated segfault after doing certain operations (leading to target
reset) from GDB. He has provided me with remote access to the specific
machine and configuration that exposed the issue, and after some
debugging it became apparent that a auto local variable (holding the
gdb connection pointer) gets overwritten somehow. Placing an
appropriate breakpoint just before the event and using a watchpoint
made the cause apparent: reset lead to freeing of all working areas,
and there was one holding a pointer to a variable that was auto local
in get_lpc2000_part_id().
Change-Id: I7e634d890135ca0f3b4b311e09e8385a03982bd6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2695
Tested-by: jenkins
This regression was introduced with d90b86d8. "transport select" doesn't
throw an error anymore and autoselects the first available transport on
its own.
Reported by moyix on IRC.
Change-Id: I3f303c0372e915931cca4b28af450694abc1a63e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2693
Tested-by: jenkins
The detection framework assumes rtos->symbols is dynamically allocated,
an assumption that the ChibiOS variant breaks by providing a raw statically
allocated symbol list.
Change-Id: I379bcc2af99006912608ddd3f646ff7085606f47
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-on: http://openocd.zylin.com/2597
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch might influence openocd Tcl commands behaviour in subtle
ways, please give it a nice testing.
The idea is that if an OpenOCD Tcl command returns an error, an
exception is raised, and then the return code is propogated all the
way up (or to the "catch" if present). This allows to detect
"shutdown" which is not actually an error but has to raise an
exception to stop execution of the commands that follow it in the
script.
openocd_thread special-cases shutdown because it should then terminate
OpenOCD with a success error code, unless shutdown was called with an
optional "error" argument which means terminate with a non-zero exit
code.
Change-Id: I7b6fa8a2e24c947dc45d8def0008b4b007c478b3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2600
Tested-by: jenkins
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Commit a35712a85c caused a regression where command
openocd -c "echo a1; shutdown; echo a2"
always returned non-zero exit status to operating system,
even when commands before shutdown all succeeded. This patch
attempt to fix this.
Change-Id: I3f478c2c51d100af810ea0171d2fd4c8fcc657f3
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-on: http://openocd.zylin.com/2589
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Found by clang static checker.
On the very first call of jim_newtap_expected_id() pTap->expected_ids
and expected_len are null, and there's nothing to copy. This patch
changes this cryptic code to use realloc() instead.
Change-Id: Ic0b5140d08257a906f15b55a2ae64db7bc06d5f1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2562
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Tested-by: jenkins
Current flash driver can fail to write across the sector boundary.
This patch fixes "thisrun_bytes" set to "cmd51_dst_boundary" value instead of "cmd51_can_xxxxb"
Referred to SevenW's post and fix,thanks.
http://sourceforge.net/p/openocd/mailman/openocd-devel/thread/fa32e7d6654df22470dc5f4a3dbc984a%40familiebenschop.nl/#msg33594152
Tested on below listed chips.
LPC810,LPC811,LPC812,LPC824,LPC1115,LPC1343,LPC1347,LPC1227,
LPC1769,LPC1788,LPC54102,LPC4088 and LPC2388.
Change-Id: If1c6a1daa58ca27c405bd959a784e599a7a8f4d4
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2607
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The original code had iterated 10,000,000 times and taken the elapsed
time divided by 10,000, to yield kHz which is mathematically correct
only if we were measuring time in seconds, but we are measuring time in
milliseconds, so the correct divisor is actually 10,000,000. Previous
code would report 0.500 for actual measured speed of 500 kHz.
Change-Id: Iba4c4961fe3973e7ccfa6dfa11d606a966ceb50c
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2573
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When the SCTLR has C set but M unset (i.e. Caching on, but MMU off) the cache
if effectively off. So only flush the cache if MMU is on, otherwise stale
entries might be committed to memory.
Change-Id: Iaff8b6f25b7a41ba838b91d45684c98f99fc0b27
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/2429
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Since SWD is currently abusing the JTAG command queue for reset and
sleep handling (and all other operations are performed in a different
way), sleep needs to be forced explicitly to ensure correct timings.
Change-Id: I5b0da6cbb7d0560154e4077b261aa6828cefc892
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2591
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Bug in read pointer check within flash write algorithm made incorrect check
if block size is more than 4 bytes (bug was detected with 16 bytes block size).
Change-Id: I5b8e7ebca619a0a85ae6e9e496ff792248134d81
Signed-off-by: DmitryShpak <disona@yandex.ru>
Reviewed-on: http://openocd.zylin.com/2657
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow most of the existing configurations for older
versions to remain compatible without forcing the user to change his
or her config to explicitly select transport.
Also in some circumstances can remove the need to chain a "-c transport
select X" when building custom configs on the command line, which seems
like a common new user pitfall.
Change-Id: Ic87a38c0b9b88e88fb6d106385efce2f39381d3d
Suggested-by: Petteri Aimonen <jpa@git.mail.kapsi.fi>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2551
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This brings SWD reconnection procedure in line with the ARM
documentation and changes cortex_m reset procedure to make use of it.
The motivation behind this patch is to make SAM4L "reset" and "reset
halt" properly without SRST. The complication here is that EDBG issues
an additional read of DP_RDBUFF automatically right after writing
SYSRESETREQ, that leads to a FAULT which needs to be dealt with
properly. With this patch the very first ahbap_debugport_init DAP
access will make SWD layer properly reinitialise the link before
continuing.
Runtime tested with mbed CMIS-DAP + KL25 only.
Change-Id: Ic506f9db30931dfa60860036b83f73b897975909
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2596
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Valgrind-tested.
Comparison of flashing performance on an FRDM-KL25Z board running mbed
CMSIS-DAP variant, 5MHz clock, old driver:
wrote 28096 bytes from file demo.elf in 26.833590s (1.023 KiB/s)
verified 27264 bytes in 1.754972s (15.171 KiB/s)
this implementation:
wrote 28096 bytes from file demo.elf in 3.691939s (7.432 KiB/s)
verified 27264 bytes in 0.598987s (44.450 KiB/s)
Also tested "Keil ULINK-ME CMSIS-DAP" with an STM32F100 target, 5MHz
clock, results reading from flash, old driver:
dumped 131072 bytes in 98.445305s (1.300 KiB/s)
this implementation:
dumped 131072 bytes in 8.242686s (15.529 KiB/s)
Change-Id: Ic64d3124b1d6cd9dd1016445bb627c71e189ae95
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2356
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many kinetis parts come in multi-bank configuration, so this
optimisation here can't be performed safely.
Investigated and fixed by Richard Braun.
Change-Id: I2b56614b47951595c403a1a8edd3afe11b85679b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2594
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
Avoids "J-Link hw type unknown 0x10" on the Infineon Relax Lite Kit.
Change-Id: I3091623ead2e84b67ac20d9866307ccbb3f26f66
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2568
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Avoids "J-Link hw type unknown 0x11" on various Infineon boards.
Change-Id: If20b9e21110d2acc02be57f5faf28c5e6a39e2c9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2565
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should facilitate dynamic target creation and removal.
Currently it helps with getting 0 bytes lost report from Valgrind on
exit (after talking to a nucleo board). However, 1,223,886 bytes in
5,268 blocks are still reachable which means the app holds pointers to
that data on exit. The majority comes from the jtag command queue,
there're also many blocks from TCL command registration.
Change-Id: I7523234bb90fffd26f7d29cdd7648ddd221d46ab
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2544
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
The target might be using Tcl examine-start and examine-end handlers,
they need to be called when the target gets reexamined after polling
succeeds again.
Change-Id: I371380c6f3c427ec7a0206d73426f6589f18a9bd
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2536
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
This bug was exposed by Valgrind.
Change-Id: I2e2bc036b49ca3ff22f78f765ee4537763350096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2543
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This bug was exposed by Valgrind.
Change-Id: If50878664d928c0a44e309ca1452089c1ac71466
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2542
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Warning, behaviour change: before this patch if a timer callback
returned an error, the other handlers in the list were not called.
This patch fixes two different issues with the way timer callbacks are
called:
1. The function is not designed to be reentrant but a nested call is
possible via: target_handle timer event -> poll -> target events
before/after reexaminantion -> script_command_run ->
target_call_timer_callbacks_now . This patch makes function a no-op
when called recursively;
2. The current code can deal with the case when calling a handler
leads to its removal but not when it leads to removal of the next
callback in the list. This patch defers actual removal to consolidate
it with the calling loop.
These bugs were exposed by Valgrind.
Change-Id: Ia628a744634f5d2911eb329747e826cb9772e789
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2541
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When target was already halted during the initial examination,
arm11_check_init() was trying to read, store and interpret DSCR
contents before the DPM structure is initialised. This caused
a segfault like described on
http://sourceforge.net/apps/trac/openocd/ticket/65 .
This is a totally untested attempt to fix this issue.
Change-Id: I2fff115679a3f0023e7a88c749ccb5f045d6cf01
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2043
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Otherwise it happens if stlink can not be opened on start.
Change-Id: I7088f10e61508dae230eccfe576a51498c92f5b8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2550
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Stian Skjelstad <stian@nixia.no>
This is runtime and valgrind tested with l0, l1 and f3 hla boards.
Change-Id: I49b0b042253d5f3bf216997f0203583db319fe23
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2516
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds the fpv4-sp-d16 registers to the armv7m register set.
The work is inspired by Mathias K but takes a different approach:
instead of having both double and single presicion registers in the
cache this patch works only with the doubles and counts on GDB to
split the data in halves whenever needed.
Tested with HLA only (on an STM32F334 disco board).
Currently this patch makes all ARMv7-M targets report an FPU-enabled
target description to GDB. It shouldn't harm if the user is not trying
to access non-existing FPU. However, the plan is to make this depend
on actual FPU presence later.
Change-Id: Ifcc72c80ef745230c42e4dc3995f792753fc4e7a
Signed-off-by: Mathias K <kesmtp@freenet.de>
[fercerpav@gmail.com: rework to fit target description framework]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/514
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by clang static checker.
Change-Id: I77b0dc18188328fdb28d07b9e5c52e06182d9e2b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2561
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by clang static checker.
Change-Id: Ifa58ba383092341c7343916e5cc8ec3c72ab2f60
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2560
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by clang static code checker.
Change-Id: Ic1370f8d7a48f08da6514afec5aacde38af7dfb6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ARMv7E-M (CortexM4) architecture
- fix position offset of r2,r3 registers on exception stack
- switch 'calloc' arguments
- remove prototypes of internal function and typedefs
- add NULL check for alloc functions
- remove last line of license "Franklin Street, Fifth Floor"
because of 'checkpatch' validation
- environment: jlink + twrk60n512
Change-Id: I70840ded15b17dd945ca190ce31e2775078da2d9
Signed-off-by: Marian Cingel <cingel.marian@gmail.com>
Reviewed-on: http://openocd.zylin.com/2353
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the at90usb128 flash (tested on the RZUSBstick)
Change-Id: Ic042d7c403b20a5cc533da00c30ae6e2139bbd10
Signed-off-by: Olivier Esver <olg.esver@gmail.com>
Reviewed-on: http://openocd.zylin.com/2557
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Solution found on the internet
Change-Id: Ied6f7d9b28131a7ac83b203e4c64d4e9ffec0595
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/2496
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Failed build on Mac OS X 10.10.2 was reported in OpenOCD-devel.
Cleaning types and printf formats. uint32_t prefered for flash/sector sizes.
2 minor changes in comments.
Removed redundant bracket.
Change-Id: Ia06b77af59c2c0ffd10869a4b263a760ca8b0a7a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2558
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Added new entries to the nrf51_known_devices_table array. New entries
are documented in the "nRF51 Series Compatability Matrix V1.0" found on
the Nordic Semi web site. Reordered entries to match the order found in
the document.
Also added an entry for an undocumented hwid discovered while flashing
the PCA10031 and PCA10028 dev boards.
Change-Id: Icca7da103d437dc28e651f27ab937fe953b9aac9
Signed-off-by: Theodore A. Roth <troth@openavr.org>
Reviewed-on: http://openocd.zylin.com/2514
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Given that the manual states that these two subcommands are
deprecated and were scheduled to be removed back in 2010,
remove them and the corresponding documentation from the
manual.
Change-Id: Iaac633349d7fcb8b7f964109c7d26dd0cc5fc233
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1860
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Based on the initial work on bcm2835gpio.c by Paul Fertser with many
additions. Modifications to the GPIO handling was minimal in this
patch. A more big modification is required before cleanup the
interface between bitbang and sysfsgpio.
Change-Id: I54bf2a2aa2ca059368b0e0e105dff6084b73d624
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is based on the initial work by Paul Fertser with addition of the
switch sequences and new ACK handling. In case of WAIT response, the
sticky bits are cleared and the last operation is repeated. The ACK
handling is based on the interpretation of the 8 February 2006 ARM
Debug Interface v5 Architecture Specification
Change-Id: Id50855b1ffff310177ccf9883dc9eb0d1b4458c8
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2437
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I couldn't make OpenOCD to work with GDB. I was always getting this in GDB:
(gdb) target remote localhost:3333
Remote debugging using localhost:3333
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Malformed response to offset query, timeout
(gdb)
While debugging gdb remote protocol, I have seen that gdb responds with:
w ++$?#3f
And those two '+' seems to confuse the OpenOCD parser, if it sees another
'+' sign it emits the DEBUG output and sets the noack_mode to 2. The
problem is that we weren't even IN noack mode, this was set to 0 and then
it explicitly sets it to 2 and thus turning the noack mode on.
Change-Id: If267c9226e57fa83121ded09cf69829f8f0b4b93
Signed-off-by: Matej Kupljen <matej.kupljen@gmail.com>
Reviewed-on: http://openocd.zylin.com/2545
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Without this patch, to perform a memory read, OpenOCD first issues an
LDC instruction into DBGITR in Stall mode (thus executing the
instruction), then switches to Fast mode and reads from DBGDTRTX once
for each word to transfer.
At the very end of the transfer, the final Fast mode read of DBGDTRTX
has, as always, the side effect of re-issuing the LDC instruction. This
causes two problems:
(1) If the word immediately beyond the end of the requested region is
inaccessible, this spurious LDC will cause a fault. On a fast CPU, the
LDC will finish executing by the time the poll of DSCR takes place,
failing the entire memory read. On a slow CPU, the LDC might finish
executing later, leaving an unexpected and confusing sticky fault lying
around for the next operation to see.
(2) If the LDC succeeds, it will leave the loaded word in DBGDTRTX, thus
setting DBGDSCR.TXFULL=1. The cortex_a_read_apb_ab_memory routine
completes without consuming that last word, thus confusing the next
routine that tries to use DBGDTRTX (this may not have any visible effect
on some implementations, because writing to DBGDTRTXint when TXFULL=1 is
defined as Unpredictable, but I believe it caused a visible problem for
me).
With this patch, the bulk mem_ap_sel_read_buf_noincr is modified to omit
the last word of the block. The second-to-last read of DBGDTRTX by that
function will cause the issue of the LDC for the last word. After
switching back to Normal mode and waiting for that instruction to
finish, do a final read of DBGDTRTX to extract the last word into the
buffer, leaving TXFULL=0.
Without this patch, memory accesses are always expanded such that they
are aligned to the access size. With this patch, accesses are issued
exactly as ordered by the caller. The caller is expected to handle
fragments at the beginning and end of the transfer if the address is
unaligned and an unaligned access is not desired.
Without this patch, the DFAR and DFSR registers, which report the
location and status of data faults, are ignored while performing memory
accesses, which could cause problems debugging an OS page fault handler.
With this patch, DFAR and DFSR are preserved across memory accesses, and
DFSR is decoded in the event of a synchronous fault to provide the
caller with more information about the reason for failure.
Thanks to Boris Brezillon for the original patch whose ideas led to the
non-word access mechanism implemented here and to various code reviewers
for their comments.
Change-Id: I11ae7104fbe69a522efadefc705c9a217a7eef41
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/2381
Tested-by: jenkins
Reviewed-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
RM0038 Rev.12 lists these new parts and introduces the category naming
scheme.
RM0367 Rev.2 (STM32L0x3 RM) doesn't add any new codes.
Change-Id: Id95dd48dda64d5f108dac57d265d29a7db3a1bd1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2495
Tested-by: jenkins
OpenOCD's SWD subsystem doesn't currently have a consistent WAIT
handling (i.e. it doesn't ever retry, just returns an error), so right
after a row write a small delay is needed as AHB access is stalled
during the flashing operation.
The issue was exposed with a samd20 using ftdi SWD transport.
Change-Id: I07d99d3a96845cc689c3904a41f4d41344f200aa
Signed-off-by: Andrej Kazmin <funnyfish@funnyfish.botik.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2268
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This optional argument tells OpenOCD to exit after finishing (either
succesfully, or with an error) the programming sequence. Without it
OpenOCD stays running.
Change-Id: I6ecaf33ff985eea9a9cd02ff644a74403ae3e1e5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2492
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently
openocd -c "echo a1; shutdown; echo a2"
outputs both "a1" and "a2" and only then shuts down. This patch fixes
it by making shutdown command throw an exception, so unless it's
caught the shutdown will behave as expected.
Change-Id: I764268b3a9046ff3e9717d04095ea0673f1d755a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2511
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Convert the DWT register store to use a byte array and fix the byte order
bug uncovered by that. Also fix an incorrect access of the PC value.
Change-Id: Idb5acab71bdf5a96895c358324b05c335e4d32ca
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2476
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The registers are represented as bit arrays intended to be accessed using
the buf_set_* and buf_get_* functions. Storing the register values in
integers enables accessing them directly, which gives different results
depending on host byte order.
Convert the register store to use a byte array instead and fix all the
byte order bugs uncovered by that.
Also merge the 32 and 64 bit register fields. Only one of them is used at
a time and after the change to byte arrays their types are also the same.
Change-Id: I456869a1737f4b4f5e8ecbfc1c63c49a75d21619
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2475
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
On armv7 there no longer are 1kB pages. Instead the bit that in
older architectures distinguished 1kB pages from 4kB pages is on
armv7 used for as execute-never marker. There may now also be 16MB
supersections with 40 bit physical address.
Change-Id: I959bdb8012782a9d07d968907a21f50e3d9b356a
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/2386
Tested-by: jenkins
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add Cortex-A5 identification to ROM-table display, and also
to cortex_a_init_debug_access. This change is mostly cosmetic.
Change-Id: I7b1dd8755d70d45eb5f315aa1918d44a813b3cdf
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/2483
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The image struct is malloc'd and hence base_address_set doesn't have a
defined value.
Caught by Valgrind.
Change-Id: Ice15b2299fc768e44e8034eeb93e035076eacd03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2524
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After profiling gmon.out was being written in little endian format only
which would cause gprof to issue and error and exit on big endian targets.
Change-Id: I526a40adae0f9a439fc5b77cef30fda228198b48
Signed-off-by: Jose de Sousa <jose.t.de.sousa@gmail.com>
Reviewed-on: http://openocd.zylin.com/2168
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I53568674951ec8a5db5e191c7b50c60b5a84d0b6
Signed-off-by: Michael Brown <fractalmbrown@gmail.com>
Reviewed-on: http://openocd.zylin.com/2463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit 832f0a5bfb 'stm32: add mass erase support for STM32L' added
use of mass-erase in-place of bank-erase. This is triggered if first
bank is requested to be fully erased.
This erroneous action completely fails on STM32L162VEY (has 512 KiB
flash in two 256 KiB banks) and also unintently destroying contents of
EEPROM and second flash bank.
Change-Id: I0f13f7b0346747a09c755d72b5b95775ceff5a6f
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Reviewed-on: http://openocd.zylin.com/2441
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Topaz reports on http://sourceforge.net/p/openocd/tickets/87/ that
protection level constants are mixed up. This leads to device ending
up in protection level 1 after mass erase.
Additional work is required to actually put the device in RDP Level 1
and then back to Level 0, as Option bootloader launch is a special
kind of full target reset.
To be able to flash properly after mass_erase a "reset init" is needed
(it's anyway recommended to always perform it before any flash
operation).
Change-Id: I9a838909458039bb0114d3019723bf134fa4d7c9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2490
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This macro makes windows builds faster and helps with the old "#define
interface struct" issue as the word "interface" is part of libusb-0.1
API. However, defining it in replacements.h is too late, as windows.h
gets included by that time from somewhere else.
This solution is provided by Ray Donnelly from the MSYS2 team.
Change-Id: I376a5fb3d106786515d7e1ba44dbd751e4dcdb1b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2486
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since libusb-0.1 might be provided by libusb-compat, it will depend on
libusb-1.0, so needs to be mentioned before it in the link command
line, this is relevant for static linking.
Thanks go to mingwandroid for spotting it during MSYS2 build.
Change-Id: I15cf0b8f084c351b4f93e75686bd0f843477352b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2485
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the new STM32F446 mcu with 512 Ko
Tested with a eval board
Change-Id: I0c16ce7d32d249c7634d697815207c20e7f778c4
Signed-off-by: prudhomme.remi@gmail.com
Reviewed-on: http://openocd.zylin.com/2484
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The message as it was didn't let the user know that something was wrong
with the target or wiring.
Change-Id: Ib609c2d31959e77413e61c348d0e31d7269d5c58
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Also remove an unrelated no-op cast.
Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2473
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This helps to uncover incorrect usage when a pointer to uint32_t is
passed to those functions which leads to subtle bugs on BE systems.
The reason is that it's normally assumed that any uint32_t variable
holds its value in host byte order, but using but_set_u32 on it
silently does implicit pointer conversion to (void *) and the
assumption ends up broken without any indication.
Change-Id: I48ffd190583d8aa32ec1fef8f1cdc0b4184e4546
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Do not use buf_set_u32 on integers; they're not buffers.
If using buf_set_u32 on integers, bytes will be exchanged on Big Endian targets.
In this particular case, FLASH_OPTCR was incorrectly written, causing it to often
contain one of these values: 0x00aaaae1, 0x00aaffef, 0x00ffabe1 or 0x00abffe1.
This write-protected the device before flash-programming, causing this command...
flash write_image erase unlock myfile.elf
... to fail, complaining about write-protection.
Repeating the above command would change the OPTCR register each time.
After applying this patch, the OPTCR remains "unchanged".
Change-Id: I73d510fcc2e81a01973ad5c6e1aa22715ebd2743
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2466
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Mass erase operation might be impacted by different factors,
apparently the most reliable way is to do it while asserting the chip
reset line.
Change-Id: Id6ab57eaec86e402ffdf4f5c8843e7735640f03e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2424
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Enable auto-creating additional discovered TAPs even if some TAPs are
predefined, avoiding initialization failure when it's not necessary.
Also, drop the arbitrary limit on the number of predefined TAPs. Still,
don't auto-create any if there are more than 20 TAPs already, to stop
a noisy connection from creating unlimited TAPs.
Create auto-probed TAPs with less noise.
Reduce code duplication between verification and auto-probing.
Change-Id: I82a504d92dbcc0060206e71f10c5158256b5f561
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The default label does just return the same error code as the case for
zero, so this can be handled by a simple if statement.
Change-Id: I61a8cb51b5e261f21eca386af7d8cbf17ffa2d44
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/2430
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the serial wasn't actually used in hid_open() call,
which meant that the first device with matching vid:pid was opened
irrespective of the actual serial number.
Change-Id: I45216ae5d9e0798e97be693c30e2f03c89b9a02b
Signed-off-by: Jaakko Kukkohovi <jkukkohovi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2487
Tested-by: jenkins
Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As of RM0091, Rev. 7, all F0 have the same revisioning scheme.
Change-Id: I0b344a1d3ca3f61f48fa151e83c549ca5333ae47
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2457
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ability to change the speed has been added to firmware versions J22 and
above. Any attempt to change on earlier versions will be ignored without error,
as the existing code does.
For supported firmware versions the driver will attempt to get as close as
possible to supported speeds (never higher).
The default stlink speed on power up is 1.8MHz.
The driver will now also print supported clocl speeds during init.
Change-Id: Iee9bd018bb8b6f94672a12538912d41c23d48a7e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2335
Tested-by: jenkins
As a note we need to cache the requested speed setting, as the
hla interface may not be ready when the first adapter_khz is called.
Change-Id: I2fa6807d5f0bd3f0365cf178bd10a230c39415a7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2334
Tested-by: jenkins
Output a similar message to what we have on low-level JTAG adapters to
avoid confusing users. Reported on IRC by chickensk.
Change-Id: I96d58410ef715b966e32d79c0aacf38596c5eb3f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2451
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Previously the jtag_add_reset(1, 0) caused the processor to be released,
and if SRSTn existed then it would then be reset again two lines later.
Change-Id: I58b7a12607f46f83caa7ed3b3cebc4195eb51ef6
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/2398
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds flash programming support for LPC5410x and LPC82x.
And adds auto flash size detection for LPC800 series.
Tested on below listed boards/chips.
LPC54102(LPCLPC54102Xpresso)
LPC824(LPCXpresso824-MAX)
LPC812(LPC812MAX)
LPC811,LPC810
Change-Id: Ie68b6d425b17ccfa83814607ee61056e99800c1c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2442
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
A7 MPCore needs unlocking the debug registers same as with A15 MPCore.
Found out by hacking on the code.
Change-Id: I613cb4fb35007b85b4a9a401577b47768bc1a08b
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-on: http://openocd.zylin.com/2344
Tested-by: jenkins
Reviewed-by: Kamal Dasu <kamal.dasu@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added Cortex-A15 support for DAP AHB-AP init code as per ADI V5 spec.
Also added changes to make the APB MEM-AP to work with A15.
Made the the cortex_a target code generic to work with A8, A9
and A15 single core or multicore implementation. Added armv7a code
for os_border calculation to work for known A8, A9 and A15
platforms based on the ARM DDI 0344H, ARM DDI 0407F, ARM DDI 0406C
ARMV7A architecture docs.
Change-Id: Ib2803ab62588bf40f1ae4b9192b619af31525a1a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1601
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When no transport is selected, the error message dumps the available
transports, but not how to actually select one.
Change-Id: I63da2a4b59e3f6cc8d30bd631e41a82636a056ef
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For example "bp 0x20000000 8 2" makes openocd segfaulting on a
stm32f4x Discovery board.
Change-Id: I1ddd46b1fa9ade78db2234ed975ccefb72539331
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/2342
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GCC-4.2 on Mac/PPC complains about size_t is expected for %zx and the build stops.
In order to avoid other problems, I've chosen simply to typecast.
Change-Id: I99b569c4d1100e729712e31d24d6539f8b5971b6
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2360
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When communication with target fails for whatever reason, it makes
sense to do JTAG-to-SWD (in case the target got power-cycled or the
DAP method was reset anyhow), SWD line reset sequence (part of
JTAG-to-SWD already) and the mandatory IDCODE read. Schedule that to
be performed on the next poll.
Fix the return values for ftdi and jlink drivers to be consistent with
OpenOCD error codes and remove ad-hoc calls to perform DAP method
switching (as it's now done from the upper layer automatically).
Change-Id: Ie18797d4ce7ac43d8249f8f81f1064a2424e02be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2371
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mateusz Manowiecki <segmentation@fault.pl>
When a target was present on OpenOCD start but later disappeared for
whatever reason (typically unstable connection or target going to
sleep) and reappeared only for a brief period of time, reexamination
would fail, and poll would no longer run. This patch fixes it.
Change-Id: I61f9b5a3f366a761320e233f4e1689f926b5556d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2370
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The IAP firmware won't return a proper status with some versions. This
happens on my CCC r0ket board and others have seen it as well [1]. So
just ignore the status code and do a (weak) consistency check instead.
[1] http://www.lpcware.com/content/forum/lpc1343-iap-read-part-identification-command
Change-Id: I0daa779d520a540629677c56857bbc20d6db422d
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Reviewed-on: http://openocd.zylin.com/2364
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The FSF address has changed; The FSF site says that
address is
Free Software Foundation
51 Franklin Street, Fifth Floor
Boston, MA 02110-1301
USA
(see http://www.fsf.org/about/contact/)
Instead of updating it each time the address changes,
just drop it completely treewide.
Change-Id: I27199f7625901f677d8105d1e8876cff00147b71
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2340
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When an enabled FPU is detected we now use an appropriate stacking.
Change-Id: I1b0f43ec22e1c55c4f10e2ffa97d4aaa77bca5ee
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/2354
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In ChibiOS/RT 3.0 the ready list pointer "rlist" is now part of the system
data structure. Since the ready list is the first element in that
structure it can be accessed via the structure's symbol "ch".
Change-Id: Idc7eaa87cb7bbad0afa0ff1dafd54283bf429766
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/2352
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
is_erased can be one of -1, 0, or 1 so it must not be checked like a
boolean value. In this case we want to erase a page unless we know it's
already erased so we just check for is_erased != 1.
Thanks to Jim Paris for pointing this out on another driver.
Change-Id: I4591186228153b64e5a9608a2aac18745e578d4a
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2368
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some J-Link fw versions require registration to be performed before
SWD operation is possible. It doesn't harm anyway, vendor's utilities
do it unconditionally.
Thanks go to Segger for providing the necessary information.
Change-Id: Iabd76c743eca86e2c817a97cb93c969fec3f7ac6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2331
Tested-by: jenkins
Added the chip definition for the Atmel AT91SAM4S4A. This chip is a 48-pin
package with 256k flash and 64k ram.
Change-Id: I8ada7d5735e31e0ce086f96f5906c7358464245c
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2254
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After SPI flash was written by the assembly language stub,
the last SPI command was not terminated by raising CS.
This left the SPI device in a hung state that prevented the
flash from being read by the M4 SPIFI controller, even after
the M4 was fully reset. To access the flash via SPIFI, it was
necessary to completely power cycle the board.
This fix adds the missing instructions to raise CS and
terminate the SPI command after the last byte. This allows
the M4 to be resumed or reset cleanly after flashing. The
SPIFI memory is now immediately accessable at address
0x1400 0000 after flashing is complete.
Change-Id: I4d5e03bded0fa00c430c2991f182dc18611d5f48
Signed-off-by: Anders <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2359
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds flash programming support for LPC1547/8/9 and LPC1517/8/9.
Tested on LPC1549(LPC1549 LPCXpresso Board with CMSIS-DAP firmware).
Change-Id: Ic95b4d62055bb9fdc2ca484696a38ccaf49ad951
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2304
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Grigori G <greg@chown.ath.cx>
is_erased can take the value 0 (no), 1 (yes), or -1 (unknown).
Checks like (!is_erased) don't do the right thing if it's -1.
Change-Id: I10ba32c99494ca803e0a7a1ba56fdd78184b96bb
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2366
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the UICR is already empty, there's no reason to return an error
just because it can't be erased again. This happens, for example,
when flashing UICR from GDB after a "monitor nrf51 mass_erase".
Change-Id: Ia6d28c43189205fb5a7120b1c7312e45eb32edb7
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2363
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
nrf51_erase_page() checks for (sector->offset == NRF51_UICR_BASE) to
determine if the UICR should be erased. However, sector->offset for
the UICR bank is set to 0 in nrf51_probe, so this code is never hit.
Attempting to erase UICR ends up erasing the first flash sector.
Use bank->base instead to determine if UICR is being erased.
Change-Id: Ie5df0f9732f23662085ae2b713d64968cd801472
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2362
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The UICR region is actually 0x100 bytes in size. Besides making the
full region accessible, having the right value is important because
GDB rounds flash addresses to the nearest multiple of the block size
when determing which flash blocks to erase.
Change-Id: I416c391cbfc7be41a03a9b9c6e42326c87391f38
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2361
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
added "Single Wire Output" and "Trace Memory Controller" peripheral
IDs to dap_rom_display(), which is invoked by the "dap info" command
Change-Id: Iea3201007bb98e6376fbb50be40a4a2e031b0a03
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
In preparation for adding serial number support.
Change-Id: I3c9fb411b79d54a4d2de067039255436ba6708c7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2328
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The mass erase for STM32L was lack because the procedure is more complex
than the procedure for the STM32F4xx.
The reference manual RM0038 (L100 subfamily) page 79 is more accurate
than the reference manual for the STM32L0xx. On the L0, the mass-erase
erase also the EEPROM. This is a limit to mass erase on L0.
The mass erase procedure is a command of telnet interface.
Tested on Discovery L053 and Discovery L100.
Change-Id: I6a1d7a3669789aea89c59a006ab2d883f3d827ca
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2319
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should make protection work as expected on all stellaris
families, including the latest Tiva C Snowflake.
Run-time tested on TM4C123x (Blizzard).
Change-Id: Ia017edb119bec32382b08fc037b5bbc02dd9000c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2267
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This introduces a new common function that allows auto-discovery of a
suitable USB interface based on class, subclass and protocol
matching. It claims the interface and returns the corresponding
endpoints number to the caller.
The need for this arised due to nRF51822 USB dongle which comes with
an "on-board Segger J-link debugger" having 3 interfaces, so the
current code can't work at all with it (in this particular case the
last interface needs to be choosen). This also removes special
handling of JLink-OB endpoint numbers as it's now possible to
autodetect them as well as the standard JLink endpoints.
Change-Id: I4d990a7a3b373efdd2949a394b32d855a168e138
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2327
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is still limited to pre-Snowflake parts and the first 64K of
flash.
Change-Id: I9ca872ada3d1a87dba6261464b2a72a15eda5ecf
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2264
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
TI's ICDI adapter supports some additional commands which a user might
want to run for debugging or other purposes, the most useful of them
being "debug unlock" that fully mass-erases the device and unprotects
the flash.
Change-Id: I26990e736094367f92106fa891e9bb8fb0382efb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2263
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change 2288 fixed the extraneous reset caused by set_configuration that
crashed the LPC Link-2 running JLink firmware and works on windows platforms.
On Linux however, conditional code was still calling USB reset and caused
the adapter to crash on any non-windows platforms.
Change-Id: Ibf2a02d0dcdd91ccb71d86231cd8311dcadfee1e
Signed-off-by: anders@openpuma.org
Reviewed-on: http://openocd.zylin.com/2297
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to [1], we shouldn't reselect an already active configuration to avoid needless device reset. This is known to cause issues with e.g. LPC Link2 with JLink firmware.
[1] http://libusb.sourceforge.net/api-1.0/caveats.html#configsel
Change-Id: I3568ada77780a521548c450090db7173f8d0b2dd
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Anders Oleson <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2288
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
There were two problems with the _protect() feature:
1. The address written was off by a factor of two because the address
register takes 16-bit rather than 8-bit addresses. As a result the
wrong sectors were (un)protected with the protect command. This has
been fixed.
2. The protection settings issued via the lock or unlock region commands
don't persist after reset. Making them persist requires modifying the
LOCK bits in the User Row using the infrastructure described below.
The Atmel SAMD2x MCUs provide a User Row (the size of which is one
page). This contains a few settings that users may wish to modify from
the debugger, especially during production. This change adds commands
to inspect and set:
- EEPROM size, the size in bytes of the emulated EEPROM region of the
Flash.
- Bootloader size, the size in bytes of the protected "boot" section of
the Flash.
This is done by a careful read-modify-write of the special User Row
page, avoiding erasing when possible and disallowing the changing of
documented reserved bits. The Atmel SAMD20 datasheet was used for bit
positions and descriptions, size tables, etc. and testing was done on a
SAMD20 Xplained Pro board.
It's technically possible to store arbitrary user data (ex: serial
numbers, MAC addresses, etc) in the remaining portion of the User Row
page (that is, beyond the first 64 bits of it). The infrastructure used
by the eeprom and bootloader commands can be used to access this as
well, and this seems safer than exposing the User Row as a normal Flash
sector that openocd understands due to the delicate nature of some of
the data stored there.
Change-Id: I29ca1bdbdc7884bc0ba0ad18af1b6bab78c7ad38
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2326
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reference code for the SAMD2x disables caching in the NVM controller when
issuing NVM commands. Let's do this as well to be consistent and safer.
Add a "chip-erase" for the Atmel SAMD targets that issues a complete Chip Erase
via the Device Service Unit (DSU). This can be used to "unlock" or otherwise
unbrick a chip that can't be halted or inspected, allowing the user to reflash
with new firmware.
Add a "set-security" command which issues an SSB. Once that's done and the
device is power-cycled, the flash cannot be written to until a "chip-erase" is
issued. The chip-erase cannot be issued by openocd at this time because
the device will not respond to a request for the DAP IDCODE.
Change-Id: I80122f0bbf7e3aedffe052c1e77d69dc2dba25ed
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2239
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When looking for a debug base address of a core, one should search
through all the ROM tables, not just the top-level one.
This code also assumes that the first found entry (in a depth-first
search) will correspond to core 0, the second to core 1 etc.
The patch is supposed to be an alternative implementation of
http://openocd.zylin.com/#/c/1313/.
Change-Id: Ifc88971a02fe3d9c00d9bf72a822ade5804d4e09
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This allows GDB to automatically switch to the thread that has
been interrupted and show you where it has stopped.
Change-Id: Icb9500dc42a61eb977e9fac55ce9503c9926bf5d
Signed-off-by: Jon Burgess <jburgess777@gmail.com>
Reviewed-on: http://openocd.zylin.com/2303
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Versaloon firmware has been updated for reporting
errors if fail on swd transactions.
Change-Id: I49ac0ad034cc9ad83cc4e43953579811d1243063
Signed-off-by: Simon Qian <openocd@versaloon.com>
Reviewed-on: http://openocd.zylin.com/2302
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the user executes a command with an invalid subcommand, the error
message is extremely unhelpful:
> flash write test.elf
flash write test.elf: command requires more arguments
This is because any command line that starts with a valid command group is
classified as a group, triggering ocd_bouncer to print the confusing
message.
Fix by requiring that to be a command group, the command line must not
contain any unknown tokens after the last valid (sub-)command group. That
is OK because command groups don't have handlers defined and thus can't
take any parameters.
Also fix the error message for "unknown" type to be similar to the error
message that is printed (by Jim) for non-existent primary commands.
Change-Id: I26950349f0909fd3961c4f9ab9b198c221cea9fc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2285
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added calls to libusb_error_name() where applicable in order to easier
understand the error messages.
Change-Id: I3fe3d4b5624ae0de37c36e54a371eba5535ccaa1
Signed-off-by: Joakim Gebart <joakim.gebart@eistec.se>
Reviewed-on: http://openocd.zylin.com/2289
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Previous to this version the code of handle_flash_probe_command would
probe a bank twice: first time by auto-probe through a call to
flash_command_get_bank and second time by calling the probe function
directly. This change adds a flash_command_get_bank_maybe_probe wich
is a more generic version of the flash_command_get_bank, that would
allow commands to decide whether auto-probing should be performed or
not.
Change-Id: If150ca9c169ffe05e8c7eba36338d333360811e3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2093
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code treats registers that are shadowed in FIQ mode in a special
way: to read them out the target is first switches to USR mode. But
since USR != ANY the current implementation later skips register read,
and the loop becomes endless in case any !valid ARM_MODE_ANY is
present at the moment arm_dpm_full_context() is called. This was
reported in https://sourceforge.net/p/openocd/tickets/76/. The issue
surfaced because 2efb1f14f6 added two
ARM_MODE_ANY registers ("sp" and "lr") which were not normally read,
so at the time a user was calling "arm reg" they were not valid.
Fix this by changing the mode appropriately while keeping the "mode"
variable state intact so it would later match register's mode.
Compile-tested only.
Change-Id: I01840e8fa20ec392220138a3f1497ac25deb080a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for QSPI flash controller driver for
Marvell's Wireless Microcontroller platform.
For more information please refer,
https://origin-www.marvell.com/microcontrollers/wi-fi-microcontroller-platform/
Following things have been tested on 88MC200 (Winbond W25Q80BV flash chip):
1. Flash sector level erase
2. Flash chip erase
3. Flash write in normal SPI mode
4. Flash fill (write and verify) in normal SPI mode
Change-Id: If4414ae3f77ff170b84e426a35b66c44590c5e06
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Reviewed-on: http://openocd.zylin.com/2280
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new FL1-K family is replacing the FL-K family. The data from all
three was based on the datasheet. In addition the 8MB S25FL164K was
tested successfully with OpenOCD on a custom board.
Change-Id: Idafeed86da12a481c0db92cc0de7ba28f50c2252
Signed-off-by: Anders <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's possible for us to fail to read the part ID code so make sure that
part_info is initialized to NULL before attempting to do so, otherwise
we could proceed and use it uninitialized and then segfault.
Change-Id: I0a3f3d3947690b66f0981b5046340449521e0b33
Signed-off-by: Jack Peel <jack.peel@synapse.com>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2276
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Luckily, TI's website has predictable URLs for the datasheets, so it
was trivial to download all the pdfs corresponding to the currently
available 71 TivaC devices. Then they were processed with pdftotext
and parsed by this script:
BEGIN { capture = -1 }
/^Device Identification 0 \(DID0\)$/ { state = "waitingclass0" }
/^Device Identification 1 \(DID1\)$/ { state = "waitingpartno0" }
/^CLASS$/ { if (state == "waitingclass0") state = "waitingclass"
else if (state == "waitingclass") capture = 4 }
/^PARTNO$/ { if (state == "waitingpartno0") state = "waitingpartno"
else if (state == "waitingpartno") capture = 4 }
(FNR == 3) { family = $2 }
{
if (capture >= 0) {
if (capture == 0) {
if (state == "waitingclass")
class = $0
else if (state == "waitingpartno")
partno = $0
}
capture--
}
}
END { print "{" class ", " partno ", \"" family "\"}," }
Change-Id: I6820c409fe535f08394c203276b5af4406fe8b92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2262
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should make current Tiva C parts usable apart from the protection.
Runtime tested on TM4C123GXL (Blizzard) and TM4C1294XL (Snowflake).
Change-Id: Ia64e9d39fbd2b7049578bbfade72435e5203ddf5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2257
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This struct and libusb_get_device_descriptor() method are not present
in libusb-0.1 API, so when libusb-1.0 is unavailable, this code breaks
the build. Fix by using the appropriate struct (which is apparently
filled automatically on device initialisation).
While at it, change return values for consistency with the callers.
Change-Id: I7d85ab9a70401a155a65122397008ae4d81382fe
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2252
Tested-by: jenkins
Reviewed-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
Commit f701c0cb seems to have introduced a regression for non-JTAG
transports as the newly created "tap" (DAP actually) ended up being
disabled, thus resulting in total lack of functionality.
This was exposed by a debug log demonstrating ftdi SWD transport
connection to mdr32f9q2i, the target wasn't examined on init and
couldn't be reset.
Change-Id: If53cbe800d4adc177aa3ac3219860e7fa15b3e49
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2261
Tested-by: jenkins
Reviewed-by: Angus Gratton <gus@projectgus.com>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This was very helpful when debugging programs during async loading.
Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds initial support for the STM32L0 family, specifically the ID
code 417 variant. The 'L0 has 128B rather than 256B pages as well as a
different number of pages per sector. It also has several key registers
and register sets in different locations from the STM32L1xx parts.
This change therefore takes the opportunity to reorganize part information into
a const table (it was previously determined by a set of control statements) and
abstracts away some of the low-level details to make them generic for L1 and
L0 parts.
We also include the first bank's size (for dual bank parts) in the new
device information table (and correct that size for the 0x437 variant
which is 256 rather than 192KB).
The 'L0 parts will not use the built-in loader/helper for Flash writing.
Tested on STM32L053 (dicovery board and Nucleo board) and STM32L152
(discovery board).
Change-Id: I57f7a8ab02caee266de71b31ae82a50d85728a0b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This was somehow missed in the chip ID table and of course that's
exactly the one on my board (as such, tested on hardware).
Change-Id: I212d7c729d979e0357f1d4635f40935e25fe6ff3
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2260
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fitted to various Analog Devices ADuCM36x dev boards.
Change-Id: Ib3691704c0ecd2f8cba1abba284aee695d6bc135
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2244
Tested-by: jenkins
As Daniel pointed out, since the rewrite of the USB Blaster driver, the
initialization behaviour has change. The initial flush of the FIFOs is
not longer done with a specific USB setup packet, but with a write
filling up the blaster queues.
The problem is, quoting Daniel :
When the CPLD is in bit banging mode (as is usually the case), the
first 0x00 byte sets all pins to low and disables the output
driver. Disabling the output drivers is a few nanoseconds slower
than changing a pin from high to low, so I see a spike towards GND
on my reset line when that byte is sent over USB. The spike is too
short to have an effect on the board.
When the 4096 0x00 bytes are processed and the TMS=1 is to be
generated, all I see is several microseconds of low level on all
pins, resetting my board.
This patch changes the way the initialization is done :
- at driver init, nothing is sent towards the usb-blaster
This gives time for init script to setup PIN6 and PIN8 (resets)
- at the very first driver command, the initialization is done :
- the output is in bit bigbang mode
- the PIN6 and PIN8 are computed according to init script
- the 4096 computed output is sent
Change-Id: If7ceee957f6b59bcb27c8f912f1cfdd0f94f75ed
Reported-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/2229
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even though changing transport is impossible, reselecting it should be
harmless.
Change-Id: I6c1c2786134e826f47f848b590e6d712b6fd2206
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2251
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In particular -f and -s options may contains paths that can easily
exceed the (old) 128 bytes buffer.
Change-Id: Ifc198536549f50663e8e588519bb9ef75dcd172c
Signed-off-by: Cristian Maglie <c.maglie@bug.st>
Reviewed-on: http://openocd.zylin.com/2241
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- stlink_usb_get_rw_status() had a bug where FAULT or WAIT responses
in read/write operations were ignored, leading to incomplete data.
- Added wrapper stlink_cmd_allow_retry to handle
SWD_AP_WAIT/SWD_DP_WAIT statuses in most commands. These statuses
appear if an SWD read or write received a WAIT ACK response from the
target more than 4 times in a row. The driver retries the operation
(with exponential backoff) before failing outright (in testing 1
retry was always enough.)
- As part of the implementation of stlink_cmd_allow_retry a large
number of lines of boilerplate were refactored.
- Fleshed out stlink_usb_error_check and added it to some more code
paths so WAIT or FAULT responses are logged to debug. WAIT responses
will be logged even if they are subsequently retried, which should
help in case the retries have subtle side effects (none
anticipated.)
Tested with two targets: STLINK F0 Discovery, Nordic NRF51822. Only
tested with STLINK V2 programmers.
Change-Id: I9af24e8f0121b035356dbb9978d6bbf4feb2e4d3
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2201
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the -irlen parameter was required even though it is not
a part of the SWD or CMSIS-DAP transports.
This may eventually need to be changed for CMSIS-DAP once that
supports JTAG as well.
Change-Id: Ia02b67840c19c7cf1c7a75063648c0174176a311
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2226
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This workaround broke usage with at least the I.MX6Q.
The comment implies that talking to the J-Link dongle itself should
fail if the target isn't reset, which sounds really strange. I'm
guessing it just triggered another bug in OpenOCD or Segger FW which
might have been fixed since. Revert and wait and see if there are any
failure reports.
Tested with Kwikstik (J-Link + Kinetis K40), not with the mentioned
adapter.
Change-Id: I97f555efe079bd99c098bf483491d9509b2363ad
Signed-off-by: Roy Spliet <rspliet@mpi-sws.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2147
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
During the initialisation a driver might need to communicate with the
target (e.g. sending jtag2swd sequence), so when doing so it should
honour the user-specified speed.
Change-Id: If84fea6057fda9edcf2c0a653edfbab2500e3cdd
[andrew.smirnov@gmail.com: fix khz/hz confusion]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2224
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Using custom build-time tools is always more problematic, especially
for cross-compiling.
This alternative implementation assumes "od" (IEEE Std 1003.1-2001)
and sed are available which should be the case for any reasonably
modern system.
Change-Id: I0208f475648c78e7dca127ff4bab60d314b2bf53
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2139
Tested-by: jenkins
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The Atmel SAMR21 is a Atmel SAMD21 with an Atmel RF233 in one package (two
dies). Tested with the SAMR21 Xplained Pro eval kit.
Change-Id: I1d79ea05834b925d7ec810527206fe86854e684b
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2194
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even if it does not return, the initialization will be failed.
But it is better to show why the error is caused.
Change-Id: I399c7c94a7156be22723a9715e594061bb414a7e
Signed-off-by: Masaki Muranaka <monaka@monami-ya.com>
Reviewed-on: http://openocd.zylin.com/2189
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If load_image address overlap with fast_data_area,
it will caouse different mysterius issues. This patch
should prevent it.
Change-Id: Ibc95e5aa3ac002a59755029496b6a72616e9287f
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1854
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis-K series has ID:0x001C0000 on MDM-AP IDR register.
Other Kinetis(L/M/V/E) series have ID:0x001C0020.
Change-Id: Iada37038cd239f7331ba80a3673b36bf7e18c555
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2195
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A previous commit changes the target name used by tcl scripts.
commit d9ba56c295
target: rename cortex_a8 to cortex_a
The current change renames target functions and definitions in the
implementation from cortex_a8 to cortex_a.
This prepares the implementation to support Cortex-A8, A9, A15-MPCore
in one place.
Change-Id: I73b5a38a92c12ba5bd3b806fbbb664817575a6d7
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1599
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with stm32f1x, stm32f4x and kl25 targets using SWD transport.
Change-Id: I118d07371b53f402ea9ac73f874460a309c05100
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1947
Tested-by: jenkins
ftime() is deprecated by POSIX.1-2008 and causes a warning on
FreeBSD.
The generic OpenOCD LOG_DEBUG implementation already outputs time of
an event with a millisecond precision.
Change-Id: Ic8e4ea27c268f07554ba519768b9bdfc4343f3e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2187
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes the issue of improper initialisation sequence and in
particular makes "cmsis_dap_vid_pid" config specification functional.
Not really elegant but it's in line with the ftdi driver and so can be
reworked in a uniform way later when the internal API is changed.
Change-Id: Ief9fc64ad0ac24e1c66727153f383e4f30a830c7
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2192
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is intended to fix cmsis_dap_vid_pid command but it doesn't
because cmsis-dap has only one transport and it's auto-selected from
"interface" command handler (before any other commands are run) and as
the result cmsis_dap_usb_open() is called too early.
Change-Id: Idaade73797d8df67a6439d096f6abc9736495599
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2191
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added Openocd commandline argument to ignore_error when the
read back TDO does not match to expected value specified with
TDO after masking with what is specified in MASK. This allows
to continue to play entire SVF file ignoring errors.
Error logs clearly show the failure reason and prints
read back TDO value.
Change-Id: I324f476fc16a003b35e6f2c5b63976431f49d54a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/2129
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the current reset_config doesn't specify availability of nTRST or
nSRST, just leave them alone, do not try to deassert them ever
(asserting would be prevented by the upper layer).
Change-Id: I90123c666e05a1c26f1e164625e82d766a3e3744
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2186
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Use a special signal instead of a dedicated swd mask. Amend
jtag-lock-pick_tiny_2 config accordingly.
Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2183
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Unfortunately, this means they're available for config files only
after selecting swd transport.
Change-Id: Ia2afc1f3bfdba8d81efbb8ab964b174c0f7e2811
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2182
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds -alias|-nalias options to ftdi_layout_signal command that
allow to declare a new signal based on an already defined one.
Change-Id: I552578ebcd12ae21957a1c0d3b7e878adeff6df0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2181
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I looked through all the target configs after stripping comments and
such from them with sed to see what jtag-specific commands can appear
first, and it looks like all the meaningful combinations should be
covered.
Change-Id: I8d543407b7f4ac8aca7354ecd50e841c8a04d5f3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2179
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Polling was disabled based on global variables jtag_trst and jtag_srst
which were never touched in non-JTAG mode. Modify the check and remove
the ugly workaround to avoid calls to a possibly uninitialized JTAG
subsystem.
Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2143
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is usable on most or all FTDI adapters using a small hardware tweak.
TCK goes to SWCLK as expected. TDO should be wired to SWDIO. For TDI there
are two options:
Either add a 74HC126 or similar tri-state buffer between TDI and SWDIO,
with OE controlled by a signal named SWDIO_OE. Or simply connect TDI and
SWDIO together via a suitable resistor (220-470 ohms or so depending on
the drive capability of the target and adapter).
nSRST (and of course Vcc, GND) may be connected too but all other signals
should be NC.
Change-Id: Id36cf4577439be96bd4e5955c3026236e1cabced
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1958
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also align them with spaces instead of tabs.
Change-Id: I1c01412a3ea77b29e8e133f5c92d05ed79d7c0f3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2133
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only
setting that is guaranteed to be implemented, as well as being the reset
value in ADIv5.0.
Thus it makes no sense supporting anything else.
Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2132
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Name of the function is already a part of the LOG_DEBUG macro, so
there's no need to include it in the string itself.
Change-Id: I18c3d5b746e9106d55104e490ccf5bc5e85cc380
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2138
Tested-by: jenkins
SAM4L requires additional steps to be taken right after SYSRESETREQ is
issued in order to function robustly:
- CMSIS-DAP DAP driver needs to explicitly check for sticky bit
errors since it is possible for adapter to perform successful
write opration, report no errors and then, under the hood, do
some other things that will result in sticky bit being set.
- Debugger needs to wait for security system to finish
intialization and assert CDBGPWRUPACK before proceeding
This change is related to commit http://openocd.zylin.com/#/c/1995/
Change-Id: I741c95a809bfd60d930cec9482239e4796a62326
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2088
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
We don't need to do full blown AP ABORT in case of CMSIS-DAP errors,
and the code that was in place was not doing that(issuing AP ABORT)
anyway.
Change-Id: Ide83b1f8875d725da6cb0d53aae8229f8c6316b3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2112
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
This should no longer be needed after tcl scripts are fixed to avoid
calling jtag subcommands when jtag is not used.
Barely tested with an frdm board.
Change-Id: I75f02b088e6134562ae634417d97c48e377df6e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2130
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It could be reused by SWD drivers and in other places.
Change-Id: Ieed0cf70c111a73d3a42ed59f46a0cdd177a73d5
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1957
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Swd_queue_ap_abort should set DAPABORT, not only clear sticky errors.
However, DAPABORT should not be set as soon as there is a single
FAULT/WAIT response. It's an "emergency only" operations for use only when
the AP have stalled the transfer for a long time. So these need to be
separate functions.
Change-Id: I37618447884faad54d846c2b07fa668ad505919d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1956
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These features are not currently used so remove or disable them before
something starts to. Not having them around simplifies redesign of the
APIs.
Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1955
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Increases performance by a factor of two for long reads.
Change-Id: I81a7a83835058560c6a53a43c3cc991100f01766
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1954
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Otherwise it breaks SWD targets. The check seems really weird anyway since
it loops through *all* TAPs after the ADIv5 target but doesn't do anything
at all with the result, other than not setting the return values despite
returning ERROR_OK.
Remove a bogus initialization that was needed because of the odd
behaviour of this routine when an IDCODE wasn't found.
Change-Id: Ic086352f6af868b3406b00420291a0a671e3acac
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1953
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix bug in parity calculation macro.
Cache and update the selected DP bank when necessary.
Add aborts when the Ack code signals a failure (we should really only
clear the sticky bits, but this will do for now).
Change-Id: I38a4da136ba1d9e989b33c1875a80c0b1b2be874
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1950
Tested-by: jenkins
The JLink protocol description doesn't really specify it for
JTAG-level commands but the real life evidence is that 0x01 error code
means "Adaptive clocking timeout" as it does for e.g. WRITE_MEM_ARM79.
Change-Id: I4e3b568742814271919f92d202713968c8fcccfb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2169
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add part IDs for the new SAMD10 and SAMD11 parts within the Atmel SAMD
family, they have the same Flash controller as the other samd parts and
should be supported by the at91samd driver. Compile-tested only.
Change-Id: I493ae96a7d7e8d19e607fd9a4b6544a982be42b3
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2170
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
while investigating coresight components, i've found some new partnumbers and devtypes.
Change-Id: Ie68032b0b21d542c2084f80db38b06f5cd4c7591
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/2166
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The error message (with the usage field unpopulated) looks like this,
obviously missing at least a space before Usage:
Error: 'fm3' driver rejected flash bank at 0x00000000Usage (null)
Change-Id: I2a625676e784d02942823f972a201f7f4f810c68
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2161
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This results in a 90% speedup on USB-Blaster, which serializes repeated
TDI input against TDO readback; program time on an 5CGXFC5C6F27 part was
dropped from 2m30s to 9s.
Signed-off-by: Joshua Wise <joshua@joshuawise.com>
Change-Id: I92d5a8b800492283d619328549235b610528c338
Reviewed-on: http://openocd.zylin.com/2145
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On a processor with caches, when you write data to memory OpenOCD invalidates
the cache lines affected. If you write to an address within 64 bytes of
UINT32_MAX, then the for loop control variable wrapped around resulting in an
infinite loop. Change control variable to be an offset from the address
involved. We should never be asked to write 2^32 bytes, so wraparound should
not be a problem.
Change-Id: Ibfe654113eff71684862ff651e7a1cd05ccc6760
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2126
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
HLAs do not provide direct DAP access, so the best we can do about it
is skipping it.
Change-Id: I877ef8fd2d86e40e7442a637cdba182cfd60e05a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2173
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
We don't need to swap the endianness in the target generic code.
This swap is necessary because of the adv_debug_if debug unit.
This patch moves this specific piece of code from or1k.c to
or1k_du_adv.c.
Change-Id: I3acea092fe6edfa79b4a87861b5f01204f071bf0
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1663
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Adds support for auto-probing on devices which support the IAP
Read Part ID command. Includes IDs for all LPC17XX, LPC13XX,
LPC11XX and LPC11XXX devices with publicly available user
manuals.
To use auto-probing, select the 'auto' lpc2000 variant.
Change-Id: Ic617c32925c9ebe0e9d9192ed8ddbfa08e9f0aaa
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2075
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
LPC11(x)xx and LPC13xx devices are mostly compatible with the lpc1700
variant of the LPC2000 driver, but use a fixed flash sector size of 4KB.
Change-Id: I033515f4ff6bc61d3b9babd27096f78c99cea927
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2071
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
stm32x_write_options is locking the FLASH_OPTCR register by
writing 0x00000001 to it, which clears the other bits. This
causes problems with subsequent flash operations; the hardware
is probably seeing the write protection bits in the register
set to '0' (protect), causing a WRPERR.
This patch ORs the value of the register with 0x00000001, so that
the only change is the lock bit itself.
Change-Id: I0e3ca9aa6563ce1b57a01fc0faf7563b6b85f620
Signed-off-by: Elliott Partridge <elliott.partridge@gmail.com>
Reviewed-on: http://openocd.zylin.com/2155
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ARMv7-R cores are largely uniprocessor-configured, and when they are
multiprocessor-configured the format of the MPIDR register isn't
compatible with ARMv7-A cores.
Change-Id: I024ec514496fbab5075c6fb34b6acd870e68e1fc
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2096
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Configuration commands assume the last created target is the one they
should be applied to. An example of this is sourcing an stm32f1.cfg
several times to access several microcontrollers on the same JTAG chain
where cortex_m reset_config should apply to the target that was just
created, not to the first one.
This fixes http://sourceforge.net/p/openocd/tickets/71/ .
Change-Id: I1ca41cc05fe5f36c4bc62dde4614da1405754fd8
Reported-by: Michael Eischer <mieischer@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2142
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the communication with the target was failing (either because of an
intermittent connection or the target was rebooted), this is needed to
reestablish operational state.
Reported-by: Tim Sander <tim@krieglstein.org>
Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I91ea2e2b2b5ef8eb27dfe9bae95ef2a919f67e4e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2152
Tested-by: jenkins
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If polling was failing, it likely meant that either the target was
disconnected or rebooted. In the latter case it needs to be reexamined
to be properly configured for the debug session, so do it just in
case.
Reported-by: Tim Sander <tim@krieglstein.org>
Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I5b067c18d9276d4e86cc59739f196ae7d0931622
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2151
Tested-by: jenkins
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move logging for cmsis_dap_queue_ap_read/write to happen after a call
to cmsis_dap_ap_q_bankselect so that that SWD operation would appear
in the log in the same sequence they happen on the bus.
Change-Id: Ic046bc753e661da7924b019c9100d6932fb686bf
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2087
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Previous to this commit 'ahbap_debugport_init' would ignore if timeout
happened or not when waiting for CDBGPWRUPACK and CSYSPWRUPACK and would
continue initialization regardless. It also would not reset the
timeout counter after finishing polling for CDBGPWRUPACK and starting
for CSYSPWRUPACK which could potentially cause some problems.
Also refactor code of both snippets into a more generic function to
avoid duplication.
Change-Id: I16e4f50e6819e08c4126e71ef8cec7db559d608e
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2086
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Fix for LOG format specifiers, this is a superset of those
exposed by the arm-none-eabi build.
Add 0x prefix for all values printed in hex.
Add LOG messages for error cases when enabling or disabling
paging.
Change-Id: I070c556e0ad31204231a2b572e7b93af22a9bc61
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2149
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The spifi_init_code blob is calling the spifi_init() function from the ROM.
This ROM function is making use of the stack. So if the stack pointer is
invalid, trying to execute this code leads to a double fault and the
target_run_algorithm() call return with an error.
This patch simply ensure that the stack pointer is properly setup before
calling the spifi_init() ROM function.
Change-Id: I42a2163cfc2c6dfe5ada97ae8eb2bb6d2e283ff7
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/1836
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b
Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is only the basic code proposed for mips32_pracc_exec() function.
It checks every pracc address against the expected address when
reading (instruction fetch).
The code expects to start at PRACC_TEXT and any subsequent read address
is obtained by adding 4 to the previous one.
After shifting out all the instructions the code executes a final check.
It checks now for the first pass trough PRACC_TEXT and shift out
only NOP instructions.
A mips core does not need an additional NOP and after the first check
it exits if there is no store access pending.
After shifting out one NOP the core must be reading at pracc text or the
code exits with error.
The code continues shifting out NOPs until all store accesses have
been performed.
After shifting out 10 NOPs it exits with error.
No assumption is made about the number of store instruction shifted out or
the ordering of the store accesses. It only checks that the number of
store accesses is the same as the number of store instructions at dmseg
after execution.
mips32_pracc_read_ctrl_addr() and mips32_pracc_finish() are added to
simpify a bit the code. Fields pa_ctrl and pa_addr are added
in ejtag_info for storing values of pracc control and address.
Change-Id: If6322d5c8cbeadcd4acd3972c0f72c8490f53c34
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1827
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is the first patch intended to make a more precise pracc check
when running in legacy mode (code executed by mips32_pracc_exec()).
It only makes some cleanups, mostly due to unnecessary code.
With the last cache optimizations for processor access (pa for short)
all the pracc functions generate the code following some rules that
make pa more easily to check:
There are no load instructions from dmseg. All the read pas are
instruction fetches. PARAM_IN related stuff is not needed.
Registers are restored either from COP0 DeSave or from ejtag
info fields. PRACC_STACK related stuff is not needed any more.
The code starts execution at PRACC_TEXT and there are no branch or jump
instruction in the code, apart from the last jump to PRACC_TEXT.
The fetch address is ever known.
For every store instruction to dmseg the function code sets
the address of the write/store pa.
The address of every store pa is known.
Current code ends execution when reading a second pass through PRACC_TEXT.
This approach has same inconveniences:
If the code starts in the delay slot of a jump it makes a jump
to PRACC_TEXT after executing the first instruction. A second pass
through PRACC_TEXt is read and the function exits without any warning.
This seems to occur sometimes when a 24kc core is halted in the delay
slot of a branch.
If a debug mode exception is triggered during the execution of a
function the core restarts execution at PRACC_TEXT. Again the function
exits without any warning.
If for whatever reason the core starts fetching at an unexpected
address the code now sends a jump instruction to PRACC_TEXT, but due
to the delay slot the core continues fetching at whatever address + 4
and a second jump instruction will be send for execution. The result
of a jump instruction in the delay slot of another jump is
UNPREDICTABLE. It may work as expected (ar7241), or let the core in
the delay slot of a jump to PRACC_TEXT for example. This means the
function called next may also fail (pic32mx).
Change-Id: I9516a5146ee9c8c694d741331edc7daec9bde4e3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1825
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Near all pracc functions store $15 in DeSave and
restore it when exiting.
There is no need to save it, if mips32_pracc_read_regs()
save this register in Desave when entering debug mode.
mips32_pracc_write_regs() needs to update it when
exiting debug mode.
Other pracc functions must not modify DeSave.
The jump code in the fastdata transfer function needs also
some little modifications.
Remark:
Like in current code the user can read/modify $15
with the cp0 31 commands.
Change-Id: I5b7dfc1b6169da846f5d2dd3ad4209a9da2c3fad
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1565
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently the code is loaded calling mips32_pracc_write_mem_generic().
Cache synchronization is not performed.
If configured as write back cache there is no chance to execute the
handler. If configured as write through cache and the cache
lines written to are not cache resident (I-side cache miss) may work.
The patch makes possible to execute the handler in a cached active
memory segment (mainly from KSEG0), but nothing else. The data
is still loaded without performing cache synchronization, code loaded
may not be executable.
Performance may not be faster. At start, for example, the code resides in
main memory, not in cache, and the core must transfer code from
memory. We can really modify the code to force a wait for the first
transfer like we do with start and end addresses, making sure the code
is cache resident for the rest of the queued transfers.
This can also may happen if we execute code (greater than the I cache size)
and the handler code is evicted from the cache.
Code tested on ar7241.
Change-Id: Iffdb4dae108b872fef0e7bacc5ea99649cdc1630
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1564
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently the functions mips32_checksum_memory() and mips32_blank_check_memory()
load the code word by word.
The bug in cache code is a good reason for doing so.
If there is no other reason we can load the code as a buffer to save time.
mips_m4k_write_memory() expect a buffer in target endianness, this is done by
target_buffer_set_u32_array().
Cleaned up exit code.
Tested on ar7241 big endian and pic32mx little endian with verify_image.
Flash erase check only tested in pic32mx.
Change-Id: Ib63ed98732b2e23b058e7349a0a57934b7604905
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1562
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Follows the the same rules of optimization used by all pracc functions.
Solves some bugs in previous code and adds support for write through caches.
Change-Id: If88c6738ca8c8197f327f22b766120a24f71b567
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1557
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is a post-release version but hopefully some fixes that went in
are worth it; also the changes here make OpenOCD compatible with stock
0.75 version if a distro maintainer decides to use it.
Change-Id: I7ad1814c7c4868198475cdca4750c3d0ee4f5f8b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2121
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Only send the new I/O state for the bytes that changed.
Change-Id: I930edc9518e6019331e68e4756acc5e92dda25a4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1999
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added SVF_BUF_LOG macro to properly print the hex buffer of parsed
string for SIR, SDR, TDI, TDO and MASK. The original debug and error
logs with respect to printing real values were misleading and also
had endianess issues. All the bits are printed now instead of just
u32 values.
Change-Id: Ie89902403bdb61ff458418446c2ca1253ea2a63f
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1964
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
As exposed by arm-none-eabi build, fix the wrong modifiers.
Change-Id: Ia6ce7c5c1d40e95059525c3e5d81b752df2fea7c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2122
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paging checking and disabling wasn't present for IO r/w,
so the commands were successful only when paging wasn't
enabled (e.g. EFI boot phase).
Change-Id: I41366c0fadff3ea1eb8a153291f20a46cd9ddec1
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2118
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
On larger FPGAs the default buffer size is not nearly enough;
automatically reallocate it as needed.
Change-Id: Ic8071e8cceddeef897ce76996c029250fd22662b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2099
Tested-by: jenkins
Reviewed-by: Kenneth Lorthioir <ibelimb@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Since c6216201b2 gdb target description
generation support is enabled by default and it counts on checking
"feature" pointer in reg_list. Both mips32 and dsp563xx neither used
calloc nor explicitly set feature (as it was a newly introduced struct
field).
This patch changes all targets to use calloc for consistency.
Change-Id: I9eceadef8b04aacb108e24ae23cb51ca3009586f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2102
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Different *nix systems use different constants, so sizeof should be
used instead. This fixes the build on OS X (as sun_path length is
hardcoded to 104 on Darwin).
Change-Id: I1df611383dedcfc6d153ec59b453a895c7d84e94
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2095
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
According to the "Arm Arch Ref Manual ARMv7-a and ARMv7-R edition" the
CPSR encoding for Monitor mode is 0b10110 (22) not 0b11010 (26) as is
currently used.
Change-Id: I73373a0029a81abc92febf518b88bf0dd4dec1fa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2081
Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Tested-by: jenkins
Reviewed-by: Younes REGAIEG <y.regaieg@gmail.com>
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If gdb was disconnected by the moment the target entered halted state,
update_halt_gdb would segfault.
Change-Id: I67477e9199c1df097be83a49e38602f975c083f5
Reported-by: Younes REGAIEG <younes.regaieg@imag.fr>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Those are breaking the build with clang 3.4 (current default compiler
on OS X 10.9.2).
Change-Id: I9f2fbfbb6d544498cb8d6a62565e4ebe7223e784
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2077
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Apparently this helper was never actually used, and current clang
produces an unused const variable warning, so it's breaking the build.
Change-Id: Ib088bef5e9c0a48942c1d417d46f738469ee7e28
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2076
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Some fixes to 'samd_protect' including:
- Fix a bug in which the value of 'set' parameter passed into the
function was ignored so it was impossible to remove flash
protection once it was set.
- Check the protection status of the sector via 'is_protected'
field of the corresponding 'flash_sector' structure to see if
any actual HW manipulations needs to be done.
- Change the way the errors during protection activation are
handled. Now even in the case of error in the middle of
protecting a number of sectors the subroutine would still update
the state of the sector protection in sectors array so as to
avoid cases where openocd thinks that the sector is not protected
while it actually is.
Change-Id: I4cc6445a98ec13bdd94c89f0711c17840738a215
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2027
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Bail early if trying to erase protected sector and also do not double-erase already
erased sectors.
Change-Id: Ic2d39af48c3b8e10e78d52dd978b9bc01f671c6a
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2026
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Bail early if trying to write to protected sector also mark the sector
we are writing to as dirty.
Change-Id: I892f83461792e1cc2dcccade7aa65717831a6805
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2025
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Remove 'first' and 'last' checks in 'samd_protect' since those
parameters are checked in 'handle_flash_erase_command'.
Change-Id: I30e5598a9ab656d81055f26cc63e291377605300
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2024
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
COMMAND_PARSE_NUMBER may return, thus any memory allocated may not be
freed, simple reorder fixes the issue.
Change-Id: I0ce444a5b032f5c49b6d33a03a8c0b71cad49c8c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2065
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GPL requires providing sources for any derived work. I do not see any
reason to not include the xscale stuff into release tarballs.
Wildcard matching is used because plain directory name matches
implicit rule for executables and xscale.c built is errorneously
attempted, and directory name with a slash duplicates a directory
(xscale/xscale) in dist.
Change-Id: Ie0266470dcb97be87a09ba2dda9b3957f7cbc2fa
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1911
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GPL requires providing sources for any derived work. I do not see any
reason to not include the rlink stuff into release tarballs.
Change-Id: I686ab88994030312aca5bdfe731a72f10803b5c3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1907
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems that when xml register support was added the rtos code was not
updated to match. This then caused gdb to return the following error when
rtos support was enabled - "Remote 'g' packet reply is too long".
Change-Id: I7429c4b1efed120e2e690678d55f3d6e87ee1ff1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2054
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
nRF51 doesn't have any sort of flash page cache so we need to write
all of the data on the word-by-word basis and poll for "Flash Ready"
bit each time.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I8caffbf69ebf9a69915724704ddbe270d1bb8d92
Reviewed-on: http://openocd.zylin.com/2050
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
SoftDevice stack ihex binary, provided by Nordic expects being able to
write data necessary for its correct operation at the adresses inside UICR.
This patch exposes UICR region of flash as a second bank on the MCU to
facilitate that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Idbc140b8de027f60655f78043877b7c054eb06f9
Reviewed-on: http://openocd.zylin.com/2013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Unfortunately due to my oversight, the original version of the
nrf51_probe function contained useless code that read the contents of
DEVICEID[0] an DEVICEID[1] registers and did nothing about it(those
registers had nothing to do with the device type information anyway).
This commit fixes that code by changing its behavior to read the HWID
field of CONFIGID register and looking up the corresponding device
information in the know devices table. This information is useful
when choosing the versions of SDK and SoftDevice for the chip
using "nRF51822 compatibility matrix".
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Ibd80b35460df4278e86e0c2500b7dcc876eec10c
Reviewed-on: http://openocd.zylin.com/2012
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Ignoring the value parameter in that function makes its code rather
misleading. Also the only caller of it, armv7m_restore_context already
does the whole "buf_get_u32" conversion business, so using
'value' also removes the waste of doing the conversion twice.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I515979c314d9b59ee1065c55b5bb5747c7e93f01
Reviewed-on: http://openocd.zylin.com/2057
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
output for flash page writes
The offset wasn't being considered in the "full page" write codepath, so any
writes at an offset were actually written out starting from page 0.
Change-Id: I5e70a1f35f144b3edd1ce6d9df9af9b5da6cf194
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/1965
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The JLink-OB (onboard) devices work the same way as the normal JLink
except that their PID is 0x0105 (and that's the only one we know of so
far) and their endpoint addresses are different due to there being a
CDC-ACM interface as well. These JLink-OB devices show up on a lot of
vendors' development kits as an integrated debugger.
This change simply checks whether the adapter we opened has a JLink-OB
PID and, if it does, uses the JLink-OB endpoints rather than the
default. To do this, we add a new routine, jtag_libusb_get_pid() to the
libusb adapter layer, it in turn just calls
libusb_get_device_descriptor(), which previously had no wrapper.
Also, checkpatch.pl doesn't like the VID/PID macros as defined so I
moved them to the array itself. This should have no effect on the code.
This change adds the 0102 through 0104 PIDs to openocd.rules as well as this
new 0105 PID.
Tested on an Atmel SAM4S Xplained board which has a JLink-OB, also
regression tested by using a 0x0101 PID normal JLink adapter.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Change-Id: I121d30e57729cda3adb66e2a5dc72e1fcb7ef8b1
Reviewed-on: http://openocd.zylin.com/2031
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I5ebc924ab66c86f1902942bebc203a34d97abc64
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1899
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
As suggested by Stian Skjelstad in a comment in:
http://openocd.zylin.com/#/c/2044/
if the USB product string cannot be read, provide a debug message so
users might get aware of a potential permission problem when looking
at the debug output.
Fix style bug found by Jenkins.
Change-Id: I6acb1c6261fec6f2bee80e4be513a5c5e29eff79
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2048
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The existing CMSIS-DAP driver matches the USB VID/PID against 0x3eb
(Atmel VID) and 0x2111 (Atmel EDBG embedded CMSIS-DAP debugger), and
then bumps the packet size from its default of 64 to 512. However, it
turned out that *all* Atmel-provided CMSIS-DAP devices (EDBG with PID
0x2111; JTAGICE3 with firmware version 3.x, PID 0x2140; new Atmel-ICE
[successor of JTAGICE3], PID 0x2141) require a 512-byte packet size.
Obviously, all run the same USB implementation inside their custom
microcontroller. Thus, it seems best to simply assume that *all*
Atmel CMSIS-DAP devices use this packet size, and don't check the PID
at all.
This has also been filed as Trac bug #68:
https://sourceforge.net/apps/trac/openocd/ticket/68
Change-Id: I942af93060fdf265fca3961841638caa6182f877
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2045
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
In the CMSIS-DAP driver, if nothing has been specified by the user, an
attempt is made to find the first device with the (mandatory)
substring "CMSIS-DAP" in any USB device's product string. However,
while (usually) all devices can be traversed, devices the user does
not have permission for cannot be read the product string from,
resulting in a NULL pointer. Trying to find the substring "CMSIS-DAP"
causes a segementation fault then.
This has also been filed as Trac bug #67:
https://sourceforge.net/apps/trac/openocd/ticket/67
Change-Id: Idfc9f072e34152e9af99fe1c8ec88c99dea4624c
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2044
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Nucleo F401 board uses STM32F401RE chip with new device id and
got more flash than existing devices (512K). This patch adds
new the identifier to probe functions so flashing will now work.
Change-Id: Ibe9c047c79244db0cfbb06610da9d84987b9f85a
Signed-off-by: Jens Hoffmann <jehoffma@gmail.com>
Reviewed-on: http://openocd.zylin.com/2037
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The timer callback is started on target init, but it makes no sense to
poll until the target is fully setup.
Change-Id: I118201e125e39be3d0a920e3ef9a3f68a2035f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2041
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We always have feature names defined by string literals and the
standard guarantees static storage duration for them. Hence, there's
no need duplicating and then freeing them.
Valgrind-tested.
Change-Id: I1b77f966c548e3694141c63bd8680735f0f47505
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2028
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new version of STLink (V2-1) has a different USB endpoint layout.
As the PID of the device also changed it's possible to change EPs used
by OpenOCD in runtime. The patch adds three new fields to stlink_usb_handle_s
and assigns right EP numbers in stlink_usb_open().
Parts of the code inspired by and used with consent of Jens Hoffmann.
Change-Id: I93b69fb889f15317e9bf864905f435905db39745
Signed-off-by: Bartosz Bielawski <bartosz.bielawski@gmail.com>
Reviewed-on: http://openocd.zylin.com/2019
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ST-LINK/V2 has limited internal buffering, such that trace data
can be missed if the target is generating data at a rate quicker than
the OpenOCD trace sampling. The issue of lost data is compounded since
individual TPIU packets may be split across individual STLINK_TRACE_EP
reads, and misleading results can occur if mid-packet loss occurs.
This patch increases the frequency of checking for pending trace data
with the aim of minimising such losses. Note: With the limited (I/O
and memory) bandwidth of the ST-LINK/V2 there cannot, however, be a
guarantee against trace data loss.
The timer callback is only added when enabling tracing, and is removed
when tracing is disabled.
Change-Id: Ibde9794b77793d3068f88cb5c1a26f9ceadcbd8a
Signed-off-by: James G. Smith <jsmith@ecoscentric.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1661
Tested-by: jenkins
Salvador Arroyo
Andreas Färber
Tomas Vanek
Peter D. Gray
Andreas Fritiofson
Uwe Bonnes
Marc Schink
Jonathan Dumaresq
Ivan Meleca
Matthias Welwarsky
Evan Hunter
Linus Walleij
Paul Fertser
Colin Helliwell
Alexander Kurz
Peter A. Bigot
Alamy Liu
anpilog
Jacob Rosenthal
Esben Haabendal
Kent Brinkley
Matthias Welwarsky
Robert Jordens
Ivan De Cesaris
Bogdan Kolbov
Jiri Kastner
Peter Lawrence
Matthew Campbell
Patrick Stewart
Oleksij Rempel
Jakub Kubiak
Karl Palsson
Felipe Balbi
Andreas Loehre
Jeff Ciesielski
Morgan Quigley
Mahavir Jain
Thomas Schmid
Jonathan Larmour
Oleksij Rempel
daniel-k
Maxime Coquelin
Andrew Ruder
Alex Forencich
Jim Paris
Nemui Trinomius
Ivan Buliev
Philipp Wagner
Austin Morton
Christoph Pittracher
Andrey Yurovsky
Kyle Manna
Alexander Drozdov
Vincent Palatin
Simon Qian
Spencer Oliver
Richard Braun
Juha Niskanen
Patrick Noffke
Ed Beroset
Uwe Kleine-König
DmitryShpak
Mateusz Manowiecki
Angus Gratton
Franck Jullien
pierre Kuo
Marian Cingel
Olivier Esver
Theodore A. Roth
dmitry pervushin
Robert P. J. Day
Jean-Christian de Rivaz
Matej Kupljen
Christopher Head
Andrej Kazmin
Antony Pavlov
Andreas Bomholtz
Daniel Glöckner
Joerg Fischer
Olivier Schonken
Jose de Sousa
Pawel Si
Michael Brown
Jussi Kivilinna
Rémi PRUD’HOMME
Jens Bauer
Jaakko Kukkohovi
Jörg Wunsch
Alexander Stein
Kamal Dasu
Salvador Arroyo
Grigori Goronzy
Christian Gudrian
Anders
Jon Burgess
Joakim Gebart
Andrey Smirnov
Austin Phillips
Andrey Skvortsov
Robert Jarzmik
Cristian Maglie
Masaki Muranaka
Fatih Aşıcı
Kamal Dasu
Mathias K
Jiri Kastner
Joshua Wise
Seth LaForge
Marco Cruz
Cosmin Gorgovan
Elliott Partridge
Alex Ray
Aurelien Jacobs
Tim Sander
Karl Hammar
Jens Hoffmann
Bartosz Bielawski