FT232H chips are new highspeed devices from FTDI. Basically these are a half of FT2232H (or a quarter of FT4232H), so only one channel which can be used as OpenOCD
interface. The chips are supported by libftdi 0.20 or later and by ftd2xx 2.08.12 or later.
Change-Id: Ic9a2c279167c3419a24f0d6befacbb83c4ffeb25
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/736
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Based on ft2232.c but uses the MPSSE layer for low-level access, greatly
simplifying the JTAG logic. Remove all libftdi/FTD2XX code and all layout
specific code. Layout specifications are instead handled in Tcl.
Use a signal abstraction to enable Tcl configuration files to define
outputs for one or several FTDI GPIO. These outputs can then be
controlled using the ftdi_set_signal command. Special signal names are
reserved for nTRST, nSRST and LED (for blink) so that they, if defined,
will be used for their customary purpose.
Depending on the type of buffer attached to the FTDI GPIO, the outputs
have to be controlled differently. In order to support tristateable
signals such as nSRST, both a data GPIO and an output-enable GPIO can be
specified for each signal. The following output buffer configurations are
supported:
* Push-pull with one FTDI output as (non-)inverted data line
* Open drain with one FTDI output as (non-)inverted output-enable
* Tristate with one FTDI output as (non-)inverted data line and another
FTDI output as (non-)inverted output-enable
* Unbuffered, using the FTDI GPIO as a tristate output directly by
switching data and direction as necessary
The data and output-enables are specified as 16-bit bitmasks,
corresponding to the concatenation of the high and low FTDI GPIO
registers. To specify an unbuffered output, use the same bitmask
for both data and output-enable.
The adapter configuration file must also specify default values for the
FTDI data and direction GPIO registers, and the channel being used (if
different from 0).
Change-Id: I287a41d4c696cf5fc74eb10d5e63578b0dc7f826
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/452
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
this header is used in numerous files and adding to config.h
simplifies its use globally.
Change-Id: Id724a9950b90504721233022c7fb5768e9bc5548
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/649
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ST-Link USB support added.
Change-Id: I2812646f2895b1529ff3f911edbdce7fa0051c8f
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/261
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
use AC_CHECK_HEADER rather than AC_CHECK_HEADERS so that we do not
generate a unrequired HAVE_LIBUSB_1_0_LIBUSB_H define.
Change-Id: I23a93d3813716dce797ca1514fdcb84533454c31
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/259
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
jlink modified to use the new usb abstaction layer.
During the configuration process we can select if use
libusb0 or libusb-1.0 library for this driver.
Change-Id: I70bc9ee2f89b7597e0f64ea80cad7f1b9070f01b
Signed-off-by: Mauro Gamba <maurillo71@gmail.com>
Reviewed-on: http://openocd.zylin.com/236
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The configuration script check for libusb-1.0 availability first and only
if not found check for libusb-0. So if both libraries are installed on the
system the build script will use libusb-1.0
It's possible to force compiling with libusb-0 with the --enable-libusb0 switch.
If the driver support only libusb0 the script check anly for it.
Change-Id: I7eb045d4e2bd553abefad53f3f4023ff46b0f5f6
Signed-off-by: Mauro Gamba <maurillo71@gmail.com>
Reviewed-on: http://openocd.zylin.com/33
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
buspirate has never supported building on native windows (mingw).
configure will now check this is not the case.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Freddie Chopin
Andreas Fritiofson
Spencer Oliver
Øyvind Harboe
Jan Dakinevich
Mathias K
Mauro Gamba
Spencer Oliver
Steve Bennett
Richard Uhler