For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Purge all legacy interface configurations so there's no more confusion
over which one to use.
Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.
Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
XDS100v3 is software compatible with the XDS100v2, but has a
different usb pid. This commit adds `xds100v3.cfg` that sources
the v2 one and changes the usb pid.
Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80
Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com>
Reviewed-on: http://openocd.zylin.com/3632
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MBFTDI is a very cheap FT2232-based JTAG adapter
for programming Marsohod FPGA board.
Please see http://www.marsohod.org/prodmbftdi for details.
Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/3604
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Leading zeros for the serial number are not necessary anymore.
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Change-Id: Ie4ff47b9cda7ccf314c6fda9a2784947db5ee4d9
Reviewed-on: http://openocd.zylin.com/3401
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added interface config file for the FTDI FT232H based UM232H module.
This should work with UM232H-B too, an even cheaper module, but
that has not been tested.
Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251
Signed-off-by: Ragnar Sundblad <raggesu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3031
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Also add further documentation about the project and how to use it.
Change-Id: Ia9878de566b3c8c1ea29f129287d5aea904d861d
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2961
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Derived from tcl/interface/digilent-hs1.cfg.
JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with
PS_SRST_B on Xilinx Zynq SoC.
Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2728
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Pipistrello is a low cost FPGA board with a Xilinx
Spartan6 LX45, a SPI flash and onboard FTDI JTAG.
This board is a good example use case for the jtagspi
flash driver talking through a proxy bitstream.
Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2846
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Also some hints around deprecated tcl/interface/turtelizer2.cfg added.
Change-Id: Ifa57b49febffaeddd5d8ff0a48833d3544927b10
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2584
Tested-by: jenkins
Reviewed-by: Harald Kipp
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When using ppdev driver 0 is the most appropriate default value as it
corresponds to /dev/parport0. Raw port address is suitable only for
direct access (I think that's parport-giveio on windows).
Reported by danitool on IRC.
Change-Id: I983c22251de6601b433ad31aaf660fb664cee7e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2572
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The signal names are changed for consistency with TI's docs and
sources.
Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137
Signed-off-by: Matthijs van Duin <matthijs@rinnic-vaude.nl>
Reviewed-on: http://openocd.zylin.com/2231
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Configure the LED to be off by default, blink on activity.
Change-Id: I8515ee66c49bddf866268b85811be15c2dbc086c
Signed-off-by: Anton Kuzmin <anton.kuzmin@cs.fau.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2539
Tested-by: jenkins
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is an integrated adapter used on the IoT-LAB boards.
Schematics are available from
https://github.com/iot-lab/iot-lab/wiki/Docs/openm3-schematics.pdf
Change-Id: I1c80e72653c3f319bb04d01e3dfddb1c2447c398
Tested-by: Quentin Lampin <quentin.lampin@orange.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2415
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to my inspection of an Olimex ARM-USB-OCD-H adapter ACBUS0
is connected directly to an SN74LVC2T45 buffer input B2, and the
corresponding output A2 is connected directly to the JTAG
connector. It seems the information in the Olimex flyer is incorrect
for the -H version and TRST can't be tri-stated, ACBUS2 is unused.
The older ARM-USB-OCD device has SN74AC244 for an output buffer and
ACBUS2 controls its !2OE, ACBUS0 connected to 2A1 (2Y1 is nTRST), in
accordance with the information flyer.
Change-Id: I22828b7b959b6f62c3f51367feb8fab9705641e5
Reported-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2286
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tim Sander <tim@krieglstein.org>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Without this SheevaPlug debugging interface can't be matched.
Change-Id: Ifca149130d03c1aa165ed1123e8540e49485f023
Reported-by: Andreas Schneider <schneider.andi@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2265
Tested-by: jenkins
According to the research by Eldar, TINY-H adapter has nTRST connected
to ACBUS0 directly via a 100 Ohms series resistor. I think it's safe
to assume the older TINY adapter does the same.
See high-res photos at [1].
This patch should fix issues with JTAG for the case when nTRST is
actually connected but is missing from the config.
[1] https://wikidevi.com/wiki/Olimex_ARM-USB-TINY-H
Change-Id: Iaaee7be30536ebb502802d38b82cd9573408f854
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2247
Tested-by: jenkins
Reviewed-by: demokmail <demokmail@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When you source a JTAG-SWD converter config, any other transport
doesn't make any sense, so just autoselect it right there.
Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369
Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2248
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
Resistor hack is runtime-tested, other configs are based on
schematics.
Change-Id: I8daffa0434cd41d142fbec7c230a302284f7aa31
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2184
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Use a special signal instead of a dedicated swd mask. Amend
jtag-lock-pick_tiny_2 config accordingly.
Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2183
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Tested on ZedBoard by Tim Sander.
Change-Id: I4316d9b4d36f01bbe91a46c78ea8bca22efb1a5a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2029
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new version of STLink (V2-1) has a different USB endpoint layout.
As the PID of the device also changed it's possible to change EPs used
by OpenOCD in runtime. The patch adds three new fields to stlink_usb_handle_s
and assigns right EP numbers in stlink_usb_open().
Parts of the code inspired by and used with consent of Jens Hoffmann.
Change-Id: I93b69fb889f15317e9bf864905f435905db39745
Signed-off-by: Bartosz Bielawski <bartosz.bielawski@gmail.com>
Reviewed-on: http://openocd.zylin.com/2019
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The XDS100v2 is often embedded in a number of platforms using the
VID/PID of 0x0403/0x6010 and a generic FTDI device description. Add
this VID/PID combination and remove the description line.
Change-Id: I370e6199ac24f802426e9541e19ee38f18f1209a
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2016
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adapter is special and needs a reset sequence to be performed
before operation. Since there're no suitable hooks to do that, we have
no choice but to ask the user to manually add the necessary commands
to his or her config file.
Change-Id: I48fb4276e77529768266840221b68c3ae26801e1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1884
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
TUMPA Lite is a cheap FT232H-based breakout board, without any
buffering. It also lacks series resistors so for some targets
(especially when not using ridiculously short wires) one needs to add
about 47 Ohms in series on every high-speed line.
The SRST line is connected directly to the FT232H too.
Real-life tested (including SRST and TRST).
Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1918
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patchs adds a new access driver for the existing
USB-Blaster interface driver.
This interface (as it is build-in on the sockit development
board) is composed of a Cypress EZ-USB plus a CPLD.
The Cypress chip as an embedded 8051 microcontroller.
When it's powered up, the firmware is downloaded to the
chip then the device is disconnected and reconnected with
the new firmware.
The USB-Blaster II protocol is almost identicial to
the old one. The only difference is that you need to
send a 0x5F before read TDO back. This command
seems to copy TDO buffer datas to the endpoint buffer.
Driver will be auto enabled if libusb-1.0 is detected.
Change-Id: I562a720a68cb4dcabeab791947d5d38776cb70fa
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1791
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
Working against openmoko gta02 target, including TRST and SRST (the
stupid samsung chip fully resets under trst, so it's actually of
little use here).
Change-Id: I831124659fc12efbccef536f07d15509c2112f92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1814
Tested-by: jenkins
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The schematics used for writing the config file were incorrect, real
hardware needs ACBUS3 _low_ as it's connected directly to the output
buffer's !OE pin.
Also apparently sometimes TUMPA comes with default FTDI IDs.
Real-life tested (including TRST and SRST) with a custom stm32f103
board, thanks to Mike Wang for the adapter sample.
Change-Id: Iab566e6d14f8392030f6ff2c8d976e1b57cf5ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds a driver for the jtag_vpi server [1]. This server is
now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC).
The jtag_vpi server provides an interface between OpenOCD and a simulated
core.
[1] http://github.com/fjullien/jtag_vpi
Change-Id: I717b72cace4845f66c878581345074f99002e21a
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added new configuration file for gw16042 device.
Also added this to interface/ftdi examples in documentation.
Change-Id: I07bb10bfc79a5d13007288cd57f254d889075214
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Reviewed-on: http://openocd.zylin.com/1563
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The end users on IRC report that actual USB device has different
information in its descriptor so it doesn't match. Remove it
altogether.
Change-Id: Id7841667390a514581e630e67b9283675803135b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1548
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Grzegorz Kostka
Forest Crossman
Matthias Bock
Andreas Fritiofson
Remco Bloemen
Antony Pavlov
Marc Schink
Andrew Kohlsmith
Tim 'mithro' Ansell
Paul Fertser
Ragnar Sundblad
Andreas Färber
Christoph Pittracher
Robert Jordens
Uwe Bonnes
Matthijs van Duin
Anton Kuzmin
Joerg Fischer
Spencer Oliver
Austin Phillips
Bartosz Bielawski
Tom Rini
Franck Jullien
Pushpal Sidhu