after handling of an exception in debug state, immediately
restore the original core state.
Change-Id: Ie53b63c9f19815f717f4df4390fbc13f0a204cc2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3996
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
to speed up debugging, don't load the complete register context
on a halt event, load only those registers that might be
clobbered during debugging.
Change-Id: I0b58e97aad6f28aefce4a52e870af61e1ef1a44f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3995
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
small changes to correct code formatting and spelling of some
log messages.
Change-Id: I645e675f8f9f4731b0271ddc55f64e8cf56ec1db
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3994
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch contains a major overhaul of the target run control,
mainly for the sake of satisfying gdbs ideas of how a target
should respond to various control requests for the debugger.
The changes allow gdb a slightly better control on how cores
are stepped: a core can be single-stepped while
other cores remain halted or continue normal execution
until the single-stepped core halts again.
Also, on any halting event (user command or breakpoint) the
system is brought into a stable state with all cores halted
before the halt is signaled to the debugger.
This patch also transitions the target code to make use of the
new CTI abstraction instead of accessing CTI registers directly.
Change-Id: I8ddc9abb119e04580d671b57ee12240c3f5070a0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3993
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
- rename "cortex_a" command group to "aarch64"
- remove default blank check, checksum and algorithm hooks
since they're not going to work in aarch64 mode anyway.
Change-Id: Ieb0046786ed9425baf6774c68f42a8285cc2aefd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3991
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Make sure all core register caches are invalidated on reset
assert, make sure to re-init debug registers on deassert.
Change-Id: I82350d04cc3eaae5e35245d13d6c1fb0a8d59807
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3990
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
introduce armv8_set_dbgreg_bits() function to make register
bit-field modifications easier to read.
Change-Id: I6b06f66262587fd301d848c9e0645e8327653de7
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3989
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The aarch32 register cache is only a separate view of the aarch64
registers. Load aarch32 registers through their aarch64 equivalents.
Change-Id: I3e932dfb782f03d73d30d942b24db340a5749e47
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3988
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Mmu faults can not be prevented on aarch64, they need to be taken and
handled accordingly. Remove the remaining stub code.
Change-Id: I6241efa594fe6b963624f9628cdf1c8e46588223
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3987
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Not specific to ARMv8, the Cross Trigger Interface
deserves an independent access wrapper.
Change-Id: I84f8faad15ed3515e0fff7f6cc5d1109ef91a869
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3986
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Replace loop by right-shift.
Inspired by patch from Alamy Liu
Change-Id: I1285f4f54c0695a93fa42e9863ed8ffa4de00f70
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3985
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Suppress some very verbose LOG_DEBUG's that are not really useful
any more.
Change-Id: I67f10ba9510a9e34a027f378f4b62b8901ddc8a4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3984
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reduce SLOCs in SCTLR retrieval and modification functions and make them
less complex.
Change-Id: Ida1a99c223743247f171b52eef80dc9886802101
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3982
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use the correct opcode for Aarch32 state, both for the breakpoint
instruction itself and the cache handling functions.
Change-Id: I975fa67b1e577b54f5c672a01d516419c6a614b2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3981
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with a Dresden Elektronik deRFmega128 module.
Change-Id: I91da3b11b60e78755360b08453ed368d6d396651
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2790
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
At framework level, the resume hook is not protected. Make sure to
not attempt a resume if the target is not halted.
Change-Id: I4dd1975a95d6c513bd4f4e999e496bc11182a97a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Basically port a fix that was already done for the cortex_a target.
Change-Id: I4cf4519159bda03ed611bc0b2e340a5dad2d85fe
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Instead of supplying a local, preinitialized "dscr" variable, use the
cached value from arm_dpm, which is kept up-to-date anyway.
Change-Id: I06d548d4dc6db68b9d984c83ed026fa9069d7875
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
arm commands are mostly unusable anyway, remove them. to be replaced
by aarch64 specific commands later
Change-Id: Ie994771bc0e86cff1c26f68f1f51ce8ec352a509
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
"currentel" special register is not accessible in debug state.
Change-Id: I9022b01b423cd9ae8227ed018d6166078ba44832
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Make debug and error messages more informative, fix spelling and
formatting errors
Change-Id: I7245f42c5153bcc95676270814d30e91c113aaed
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
struct arm_reg::value[] must be 8 byte to hold a 64bit register value.
Change-Id: If253e90731d0ee855eafd9d7b63b91f84630cc7c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move clearing of DSCR "Sticky Error" condition to the
exception handling function. Clear once on entering debug state.
Change-Id: Iec1d09d6f2d9cdd7e92953da5ea19f3e399ca12c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
recommended for Corte-A8 cores, not sure if necessary
for ARMv8 based cores as well.
Change-Id: Ibcb36170c5fac6a6b132de17f734c70a56919f9b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Remove register cache invalidation and target state changes that are
handled appropriately in other functions.
Change-Id: Ic903f41ddc267f4b8765ea022bd4d6da1017e21f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When a PE is in Aarch32 state and gdb asks for a target description,
provide a register view compatible with the "org.gnu.gdb.arm.core"
feature. Only current-mode registers are exported, banked registers are
not visible.
Change-Id: I99a85d94831cf597fe8cff6a0a1818ce0a33613b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to TTBR in EL0. Circumvent by moving the PE to EL1
before reading, and switch back to original mode afterwards.
Change-Id: I22891b958d3d7e6fad1cb27183c192d975d63d89
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When halting a group of PEs through CTI, HDE must be set in EDSCR for
all of them.
Change-Id: Iaa4bc0b0fe31e46a463c709d8274023225affd85
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When an armv8-a PE causes an exception while halted, e.g. by performing
a prohibited memory or register access, its state is affected in the
same way as if it was running. That means, a number of registers is
overwritten (notably DLR and DSPSR, but also others) and also
potentially the exception level and therefore also the PE state can
change. This state must be restored before resuming normal operation.
This is done by marking the relevant cached registers "dirty" so that
they are written back before resume.
Change-Id: I9b6967a62d7cb23a477a9f7839f8d2b7087eed09
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use proper T32 opcodes for cache identification when the PE is in
Aarch32 state
Change-Id: I9cd9169409889273a3fd61167f388e68d8dde86d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
DCPS only allows to enter higher ELs, for lower ELs you need to
use DRPS. Also, of course the encoding differs between A64 and T32.
Both DCPS and DRPS also clobber DLR and DSPSR, which then need to be
restored on resume.
Change-Id: Ifa3dcfa94212702e57170bd59fd0bb25495fb6fd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
All register access is now performed through common read/write
functions, which delegate the actual register access to the
armv8_common object. armv8_common contains function pointers
to direct read and write requests to the respective low-level
functions for each PE state.
The respective read/write functions are selected on debug state
entry.
At the same time, T32 opcodes are now formatted for ITR in
dpmv8_exec_opcode() and the T32_FMTITR macro is removed from global
visibility.
Change-Id: I9eaef017c7cc9e0c531e693c534901bfdbdb842c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Read registers based on current EL instead of PE mode.
Change-Id: I05d3219ac1bf8585e9f4f024a7e8599fea0913b6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to system control register in EL0. Circumvent by
moving the PE to EL1 before reading, and switch back to original mode
afterwards.
Change-Id: I309f4eea5597ffc88fc892e9bbb826982e8a44ec
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Translate from cpsr value to "enum arm_mode" by shifting up 4 bits and
filling the lowest nibble with 0xF.
Change-Id: Ic32186104b0c29578c4f6f99e04840ab88a0017b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use AT commands to translate virtual to physical addresses based on
current MMU configuration.
Change-Id: I1bbd7d674c435541b617b17022fa9f7f0f01bdab
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set HDE bit through helper function instead of manual mem_ap access.
Change-Id: I68c157870f3f3c47a875d425ade6e975d8075424
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The artificial "os_border" doesn't exist in aarch64 state and is wrong
for aarch32 state as well. Remove it.
Change-Id: I7c673a1404b03aa78dbd505e115fa3a93f7ca05f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Update cache identification to match functionality present in
armv7a_cache.c
Change-Id: I2dc4bee80f5a22b8728334d40331c183d1406f27
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move all DPM related functions from aarch64.c to armv8_dpm.c.
Change-Id: I43404ff5db414ae898787a523d3219e5bee44889
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add database for common, equivalent opcodes for Aarch32 and
Aarch64 execution states
Revisit all functions that access Aarch64 specific registers
or use Aarch64 opcodes and rewrite them to act depending on
current state of the core.
Add core register access functions for Aarch32 state
Add function to determine the core execution state without
reading DSPSR.
Change-Id: I345e9f6d682fb4ba454e4b1d16bb5e1b27570691
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set up CTI so that halt and resume requests get routed to all PEs in the
SMP group.
Change-Id: Ie92cfd3fe54632e5fdc049a6bf5b24b99451a8c9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
For now only D-Cache flush (Clean&Invalidate) and I-Cache
invalidate are implemented. That's enough for software breakpoints.
Change-Id: I8e96d645a230b51e3490403f4564e59ba6a76cf3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
On live hardware, interrupts will happen while the core is
held for stepping. The next step will most of the time execute an
interrupt service instead of the next line of code, which is not
what you expect. Disable interrupts through DSCR before resuming
for a step, and re-enable them again after the step happened.
This should be made configurable, like on cortex_a target.
Change-Id: I94d8ffb58cf7579dedb66bc756b7eb6828b6e8e4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
External debuggers need to use HLT, not BRK. HLT generates a halting
debug event while BRK generates a debug exception for self-hosted
debugging.
Change-Id: I24024b83668107f73a14cc75d951134917269e5c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Matthias Welwarsky
Marc Schink
Karl Palsson