Originally the LPC17xx user guide (UM10360 Rev 2) stated that SYSRESETREQ
was not supported, so this was the default cortex_m reset mode.
Rev 3 of the same user guide states that it is now supported.
This has been verified on a LPC1768 mbed platform, previously I have not
tested this functionality.
Change-Id: I4858248903981a1c93ce75016e67c9e02702fcc5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1892
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patchs adds a new access driver for the existing
USB-Blaster interface driver.
This interface (as it is build-in on the sockit development
board) is composed of a Cypress EZ-USB plus a CPLD.
The Cypress chip as an embedded 8051 microcontroller.
When it's powered up, the firmware is downloaded to the
chip then the device is disconnected and reconnected with
the new firmware.
The USB-Blaster II protocol is almost identicial to
the old one. The only difference is that you need to
send a 0x5F before read TDO back. This command
seems to copy TDO buffer datas to the endpoint buffer.
Driver will be auto enabled if libusb-1.0 is detected.
Change-Id: I562a720a68cb4dcabeab791947d5d38776cb70fa
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1791
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested with SAMD21J18A on the SAMD21 Xplained Pro board.
Change-Id: Ice9ebcd229ed038b3193baf92d910f9256d7ce91
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1873
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a new NOR Flash driver, "at91samd", which supports the
built-in Flash on Atmel's D-series Cortex M MCUs, starting with the D20.
Parts and their geometry are detected automatically using the DSU and
lookup schemes described in the D20 document, 42129F–SAM–10/2013.
Future D-series variants and families should presumably use this
controller as well (possibly with minor changes and improvements).
Tested on the SAMD20 Xplained Pro board, for which we also add the
corresponding Flash configuration.
Change-Id: Id8d3dd601e9f53121682d1a1190d0be4ea3b83eb
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1684
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a new NOR Flash driver, "at91sam4l", which supports the
built-in Flash on Atmel's low-power SAM4L family of Cortex M4 MCUs.
Parts and their geometry are detected automatically using the Chip ID
and lookup schemes described in document 42023E–SAM–07/2013.
Tested on AT91SAM4LC4CA via the SAM4L XPlained Pro development kit.
Change-Id: If73499dee92cc8ce231845244ea25c6984f6cecd
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1639
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These kits feature a CMSIS-DAP compliant debugger and so have been added
as part of the pending support.
Currently the flash drivers for the L8 and D20 are wip.
One issue this implementation of CMSIS-DAP raised is that it supports
512byte HID reports, however using the current HIDAPI we have no cross platform
way of querying this info. Long term we plan to add this support to HIDAPI.
Change-Id: Ie8b7c871f58a099d963cd71a9f8a0105a38784e9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1625
Tested-by: jenkins
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
This adds a set of helper functions with the aim to make it possible
to flash mass-market devices without RTFMing altogether (i.e. to
obsolete GPL-violating proprietary tjtag and other similar software).
Real-life tested on an RT-N16 and WRT54GL.
Change-Id: I197a9b28a5f386803f081057c4b4ebf2f9c447b1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1850
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested flashing a real v1.1 device.
Change-Id: Ie0d202b9fded8b92e731d93e0ef17be415a75fc8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1852
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".
The RAM setup is not done as it would require considerable efforts
without much practical gain.
The only issue I noticed so far is that "reset" doesn't actually reset
the chip.
Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.
Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.
Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* openocd.berlios.de -> openocd.sourceforge.net
* Update link to AM/DM37x Technical Reference Manual (ver R)
* "ICEpick" is properly spelled "ICEPick" according to TI
Change-Id: Ie04458e82c97ef766ec03bd9b9f27edadf5d1cb2
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1856
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The set command was missing the $ prefix on the SJC_TAPID variable
and so would fail if SJC_TAPID was set
Change-Id: Ib9af58f5188bd8a2bc3f888309f203d624476c27
Signed-off-by: Alex Murray <alex.murray@cohdawireless.com>
Reviewed-on: http://openocd.zylin.com/1811
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on Nemuisan Tokusei's. Untested, but original config was reported
to work ok.
Change-Id: Ic991dce55bfca266880081fe2bbd9e6e263b0fc0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1803
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
all other at91 cfg files already has this fix.
It also fix "No flash at address 0x...." error when JTAG chain consist of
more than one at91sam7sx cores during attempt to flash other than first mcu
in chain.
Change-Id: I7785d9103d0fc494b6a823e2c73f850373ffe112
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1812
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32F42xxx & STM32F43xxx series boudary scan TAP-ID are differ from
STM32F405xx/07xx & STM32F415xx/17xx.
And Section number was also fixed for RM0090 rev5.
Tested on a STM32F427IIT6 and STM32F429ZIT6.
Change-Id: Ie9c54c55b97b9c396ace752d94ea2ad916cc8479
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1808
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a Cortex-M1 controller targetting aviation appliances.
Contributed (and live-tested) by 8daemon.
Change-Id: I133d6122cf6492b51ddbdbd800c16ba121d51bf3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1818
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Working against openmoko gta02 target, including TRST and SRST (the
stupid samsung chip fully resets under trst, so it's actually of
little use here).
Change-Id: I831124659fc12efbccef536f07d15509c2112f92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1814
Tested-by: jenkins
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the TMS570 Cortex-R4 MCU from TI and their USB stick
development kit, TMDX570LS31USB. Tested attaching, reset/halt/run, and
reading and writing memory and registers.
Change-Id: I12d779cef0c2b834f9bcf722307f35677cc4bd8f
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1788
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The schematics used for writing the config file were incorrect, real
hardware needs ACBUS3 _low_ as it's connected directly to the output
buffer's !OE pin.
Also apparently sometimes TUMPA comes with default FTDI IDs.
Real-life tested (including TRST and SRST) with a custom stm32f103
board, thanks to Mike Wang for the adapter sample.
Change-Id: Iab566e6d14f8392030f6ff2c8d976e1b57cf5ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a tcl implementation of public domain tests by Michael Barr,
http://www.barrgroup.com/Embedded-Systems/How-To/Memory-Test-Suite-C
The initial porting is done by Shane Volpe and posted to the mailing
list:
http://www.mail-archive.com/openocd-development@lists.berlios.de/msg16676.html
This patch includes some cosmetic amendments plus hardcodes 32bit word
size (as the code depends on memread32/memwrite32 anyway) which fixes
original code's issue of testing only the first quarter of the
specified nBytes.
Change-Id: I5f3a66f1f16fc4082c7a5a6aba338430646ed21c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1455
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Some boards might have RCLK omitted from the JTAG connector and if the
interface claims support for it, OpenOCD will end up trying to use
RCLK while it's actually impossible.
This is a "cd tcl/target; sed -i s/jtag_rclk/adapter_khz/g *" patch.
Change-Id: Iee7337107bc1457966b104389ba9db75a9c860b4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1695
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Initial support for using the jtag interface to the Marvell Armada 370
family of SoCs.
Change-Id: Id823a567e8805ac622c3c330bc111297c1dae37e
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-on: http://openocd.zylin.com/1690
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Almost the same as the LM4F120 LaunchPad but the chip is using the new
naming scheme (Tiva C series), supports USB OTG and has some new PWM
hardware blocks.
Change-Id: I6a7b2df76768766471f366cddaf64df3cc63f5f2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1647
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds a driver for the jtag_vpi server [1]. This server is
now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC).
The jtag_vpi server provides an interface between OpenOCD and a simulated
core.
[1] http://github.com/fjullien/jtag_vpi
Change-Id: I717b72cace4845f66c878581345074f99002e21a
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The smallest available RAM size for this family is 2K, set this as the
default. Issue reported by quitte on IRC.
Change-Id: I3318f7f268f7681ffe2cddab61820f4b94c4e5fd
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1559
Tested-by: jenkins
Added new configuration file for gw16042 device.
Also added this to interface/ftdi examples in documentation.
Change-Id: I07bb10bfc79a5d13007288cd57f254d889075214
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Reviewed-on: http://openocd.zylin.com/1563
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The end users on IRC report that actual USB device has different
information in its descriptor so it doesn't match. Remove it
altogether.
Change-Id: Id7841667390a514581e630e67b9283675803135b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1548
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This commit adds two tcl configuration files, one for the Altera
Cyclone V SoC series, and one for the SoCkit development board.
The board configuration is able to halt and resume the cpu cores,
and dump register contents etc. It has not been fully tested, however.
Change-Id: Id3f18c3408975cf986a5f5aec410b5b13240c35e
Signed-off-by: Brad Riensche <brad.riensche@gmail.com>
Reviewed-on: http://openocd.zylin.com/1494
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds example config and flash driver for russian Cortex-M3
microcontroller model.
Run-time tested on MDR32F9Q2I evaluation board; the flash driver
should be compatible with MDR32F2x (Cortex-M0) too but I lack hardware
to test.
There're no status bits at all, the datasheets specifies some delays
for flash operations instead. All being in <100us range, they're hard
to violate with JTAG, I hope. There're also no flash identification
registers so the flash size and type has to be hardcoded into the
config.
The flashing is considerably complicated because the flash is split
into pages, and each page consists of 4 interleaved non-consecutive
"sectors" (on MDR32F9 only, MDR32F2 is single-sectored), so the
fastest way is to latch the page and sector address and then write
only the part that should go into the current page and current sector.
Performance testing results with adapter_khz 1000 and the chip running
on its default HSI 8MHz oscillator:
When working area is specified, a target helper algorithm is used:
wrote 131072 bytes from file testfile.bin in 3.698427s (34.609 KiB/s)
This can theoretically be sped up by ~1.4 times if the helper
algorithm is fed some kind of "loader instructions stream" to allow
sector-by-sector writing.
Pure JTAG implementation (when target memory area is not available)
flashes all the 128k memory in 49.5s.
Flashing "info" memory region is also implemented, but due to the
overlapping memory addresses (resulting in incorrect memory map
calculations for GDB) it can't be used at the same time, so OpenOCD
needs to be started this way: -c "set IMEMORY true" -f
target/mdr32f9q2i.cfg
It also can't be read/verified because it's not memory-mapped anywhere
ever, and OpenOCD NOR framework doesn't really allow to provide a
custom handler that would be used when verifying.
Change-Id: I80c0632da686d49856fdbf9e05d908846dd44316
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1532
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Austriancoder on IRC reports getting this ID on his board.
Change-Id: Ie859f0ee422e18fdb94bf817cdd2b41d15b968da
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1533
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for DENX M53EVK board and it's integrated on-board
JTAG adapter using FT2232H.
Change-Id: I022dcafa7799bb84a7873ba67ed82f1e49094320
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1461
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Pull the jtag_rtck setting from imx51.cfg and imx53.cfg . Since
not all boards using these CPUs do support RTCK signal, move the
configuration of RTCK into board files.
Change-Id: I632c5d38e00ada8779a451cd26428fd122452001
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1460
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It pointed to the Flyswatter 1 page.
Change-Id: Ib7e82669a31cad2bf8f6ba4a60b25ef9920b2584
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1478
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Ignore version of Boundary Scan TAP in newer revisions of the str9.
Change-Id: I6e205f8c731f07078c469e686025857c180f3a6d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1436
Tested-by: jenkins
Add a config file for TIAO USB Multi-Protocol Adapter.
Based on schematics from http://www.mediafire.com/?zv158nnx1gv0cy2
Cc: Volkan K <volkan-k@users.sourceforge.net>
Change-Id: I0dfd93b0b1e558e4ccd7c94c005c099947ec94df
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds support for JTAG programming by bitbanging GPIOs exposed on
the RaspberryPi's expansion header.
Tested by connecting directly to an STM32VLDiscovery board, without any
additional circuity. I observed maximum about 4MHz on the TCK pin with an
old analogue 'scope and about 100kHz when setting the speed to 100kHz.
Busyloop waiting is needed because even with a single 0ns nanosleep call
(with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low
to be useful.
The speed testing with adapter_khz 2000 gave the following results:
sudo chrt -f 1 nice -n -19 ./src/openocd \
-f interface/raspberrypi-native.cfg \
-c "set WORKAREASIZE 0x2000" \
-f target/stm32f1x.cfg -c "adapter_khz 2000"
wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s)
dumped 131072 bytes in 1.445699s (88.538 KiB/s)
This is 3.7 times faster for writing and 14.3 times faster for reading
compared to the generic sysfsgpio driver; probably the writing speed is
limited by the target itself here and reading speed might be considerably
higher too with appropriate connection and a capable target.
BCM2835 name is choosen over BCM2708 because the published peripherals
datasheet uses the particular model name and not family name.
Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/758
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updated OpenJTAG driver from www.openjtag.org to work with latest version of OpenOCD.
Change-Id: I2917f4e5835fb9ca5265e81dc38515fa97ae9503
Signed-off-by: Ryan Corbin <corbin.ryan@gmail.com>
Reviewed-on: http://openocd.zylin.com/1406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add target code for Andes targets.
Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andes AICE uses USB to transfer packets between OpenOCD and AICE.
It uses high-level USB commands to control targets instead of using
JTAG signals. I define an interface as aice_port_api_s. It contains
all basic operations needed by target-dependent code.
Change-Id: I117bc4f938fab2732e44c509ea68b30172d6fdb9
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1256
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is reported as working by mitsakos on IRC.
Change-Id: I26b97779c3e8e237c5b3996aa81183031b12ec0c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1419
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d9ba56c295 did a bunch of
renaming of cortex_a8 to cortex_a, including the names in config
files. However that introduced a regression as the name in target_type
struct remained unchanged.
This adds the last missing bit: actual renaming of the target name as
understood by OpenOCD.
Also change the (hopefully) last instance of using it in the supplied
config files, namely from imx6.cfg.
Change-Id: Ib9289fc6d946630133ec6e36c20015ccb50acf61
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1420
Tested-by: jenkins
Reviewed-by: Chris Johns <chrisj@rtems.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is needed for configs that might be used with the cheapest
STM32F100 parts that have only 4kB SRAM.
Restrictions for the other STM32 families are verified to be set
appropriately.
Change-Id: I1ad2370435015604db9f27c1a76c153480311a28
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1378
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to reports of newer targets using a updated version of the ICEPick tap
rather than add another tapid we ignore the tap version.
Also see Trac 49 for details.
Change-Id: Ic78414c54af2545c817e1bb2c860970c1b587259
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1373
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
As requested, here is the target configuration that I'm using for an
STLink-V2-attached STM32W108C8. For some reason, it only seems to work
with "reset_config trst_only".
Change-Id: Icbff4f83343e1f505d8afdfc53ff6f8b7496cac9
Signed-off-by: Ben Nahill <bnahill@gmail.com>
Reviewed-on: http://openocd.zylin.com/1347
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By default pic32mx starts after any reset with 1 wait state for RAM access/exec.
It can be changed to 0 wait states by clearing the BMXWSDRM bit (bit 6) in BMXCON register.
With 0 wait states near doubles the execution speed. CRC check sum can be done much faster
increasing verify_image speed. Fast data transfer also works with a bit higher scan rate, up to 1500 Khz.
This option can be set at any time with
mww 0xbf882004 0x40
or cleared with
mww 0xbf882008 0x40.
Some numbers for FTDI/HS with current devel code and a elf file:
Core clock / wait states verify_image speed
------------------------------------|------------------------------
4 Mhz / 1 21 KiB/s
4 Mhz / 0 36 KiB/s
8 Mhz / 1 37 KiB/s
8 Mhz / 0 57 KiB/s
Change-Id: I4092ad0f3753f72f77108718d0ed3a3ab84e3b23
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1141
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This config file add support to the opendous cable based on the chip ft2232H,
using the ft2232 interface driver.
Change-Id: I8171a0c475af8d61e081844ee86466a392138fb0
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1096
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config file add support to the opendous cable based on the chip ft2232H,
using the ftdi interface driver.
Change-Id: I4491f99d7b14f7078a04583ef0c4acd8692c4349
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This change adds a simple target configuration for Freescale
single/dual/quad core i.MX6 SoCs, only one core is configured by default.
Change-Id: I853dd27f4c6765b7f731be2ddea82e85d496c6a4
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-on: http://openocd.zylin.com/1135
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch change the default reset config from SYSRESETREQ to the working
VECTRESET.
Change-Id: I21a9a74b9c0c68cfa3a6e6dac9b123acc98a93cb
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1186
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update adds support for the STM32Lx 384kb dual bank flash. Previously there was a problem when writing an
image that was larger than 192Kb. That lead to openocd printing out two error messages like
"Error: access denied / write protected" and "Error: invalid program address". The reason was that the stm32lx
driver tried to write half pages which overlapped into the next flash bank.
A new configuration file stm32lx_dual_bank.cfg can be used for stm32lx chips with dual bank flash (256kb or 384kb devices).
A sanity check was added for probed flash size values to fix the issue seen on some ST samples that answered incorrectly.
Change-Id: I69e25131983d88613be8606b438f98870c5f1e52
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
adapter_init (core.c) won't check speed configuration
of the selected interface if it's not needed (.speed = NULL).
When it's not needed, we can now omit adapter_khz in
init scripts and we don't have to implement dummy handlers
for speed_div and khz functions.
It also removes calls to adapter_khz in interface configuration
files when not used anymore.
Change-Id: I6eb1894385503fede542a368f297cec6565eed44
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1131
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This part has 16k ram so make it all available.
Change-Id: Ifeb7bc850bfe4f68d0affb8f6a0931b4327e7257
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1006
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The smallest pert in the family has 10k RAM, so use that as a default
for the working area.
Change-Id: I78be0d14a254c109ac15a7163552c6132f810416
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1005
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Switch to using the internal HSI when a reset init is called, this also
matches the std stm32l cfg.
Read (verify) speed is increased from 17 to 120 KiB/s.
Change-Id: Ic94ba85949ffdefa17b7be45eef14e30f941d107
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1004
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
As part of the switch to using the hla for the stlink interface we rename
the cmds to a more generic name.
Update scripts to match new names.
Also add handlers for deprecated names.
Change-Id: I6f00743da746e3aa13ce06acfdc93c8049545e07
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/921
Tested-by: jenkins
Even though the stlinkv1 and stlinkv2 use different usb classes they share
the same layout scheme.
Merge the two into a common layout, thus enabling us to support other
adapter layouts.
Change-Id: I7d02c44a7f94ebc7f2cb5428b02ee40294fb430d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/918
Tested-by: jenkins
As for openocd 0.6.0-rc2 the function mips32_pracc_fastdata_xfer()
should now work at a scan frequency up to 1200Khz.
Mainly usefull to increase programming speed.
Also verify_image should be slightly faster.
Change-Id: I1e9b2be73690a4597e2f6ba069c1205026850f07
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/805
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added a new configuration file for LPC18xx based boards, such as
HitexLPC1850RevA Evaluation Board, and all other based on the
same microcontroller by NXP.
Change-Id: I68c3827be535b6d09a5c70b6d57191937d00354d
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/930
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config file is intended as an example of how to
use the lpcspifi flash driver, but it should be functional
for most LPC1850 boards utilizing SPIFI flash.
Change-Id: I855854282336701fd210134497ce014017f3aaec
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this avoid driving nSRST high after startup, by making sure the nOE is
initialized inactive/high.
This also matches the config used for the STM32-PerformanceStick.
Change-Id: I9376de575b7dc834310d57dbd58575d51f60183e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/878
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
The cortino uses a direct srst connection rather than via any buffer.
As a result this fixes issues with the newer ftdi driver.
Change-Id: I28f6781bccae24de79aa6a03161f298a14fe2581
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/850
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This hardware uses a output enable buffer that was not correctly defined.
Fixes issues when using the new ftdi driver.
Change-Id: Iba6235a71a6d3c7d16ab729f858b336a4574dfea
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/844
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
The str9-comstick uses a direct srst connection rather than via any buffer.
As a result this fixes issues with the newer ftdi driver.
Change-Id: I0968e8459997a6a2b7bf0c46e89662cd57b4f496
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/842
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This driver implements a bitbang jtag interface using gpio lines exported via
sysfs.
The aim of this driver implementation is to use system GPIOs but to avoid the
need for an additional kernel driver.
A config suitable for RaspberryPi is included.
Change-Id: Ib2acf720247a219768d1cbfeebd88057ed2d7b8b
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Reviewed-on: http://openocd.zylin.com/762
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
DISTORTEC's JTAG-lock-pick Tiny 2 is a new interface using FT232HL chip
and layout similar to KT-LINK.
Change-Id: I2831b169cd448ca70397f2dd86c5b749dda3dabf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/787
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the target supports SYSRESETREQ make sure we use that as the default
if srst is not fitted/configured.
Change-Id: I24c907493134506320e69c1218702930629c1cdc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/792
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This file is already included as olimex-arm-usb-ocd.cfg.
Change-Id: I0e66977c58e74ac93a0dc3a0c88a5e5af4992f8b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/780
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The embedded projects shop released a new highspeed version of
the openocd-usb adapter. These configuration files adds support
for it.
Change-Id: I9b23d7889f998712b9041af101e3f0b9aba85b28
Signed-off-by: Andrew Karpow <notandyk@gmail.com>
Reviewed-on: http://openocd.zylin.com/771
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Add cfg files for Hitex LPC1768 Stick
Website: http://www.hitex.com/?id=1602
This board has a FTDI2232D as JTAG interface, using the
same layout as the Hitex STM32-PerformanceStick but with
different USB PID.
Main MCU is a LPC1768 from NXP.
The interface config uses the ftdi driver instead of ft2232.
The corresponding ft2232 layout would be "stm32stick".
Change-Id: I1fd15588c5af35f7d51777d1ad958cc1dc72c6f7
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/763
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
part 4 - files that are currently untested
Change-Id: Ic4a08fdefc99e7a9d50885c888c3fca60ffa39bd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/750
Tested-by: jenkins
part 3 - files that are currently untested but verified with schematics
Change-Id: Ia00c3b6437bffcfa0d178e779926ad9309e289fe
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/755
Tested-by: jenkins
part 2 - files that are currently untested but assumed to work, as other configs using the same layout work
fine
Change-Id: Ifaa1904227ebdc394362ccaf3ad3c5384a716657
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/754
Tested-by: jenkins
part 1 - files that were tested an verified as working fine
Change-Id: If5986853a1cf118a9eb3b4c13b036d0f71c39624
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/534
Tested-by: jenkins
- Moved variant-independent code to lpc17xx.cfg, which will be included from
lpc17??.cfg files automatically.
- lpc1768.cfg filled with variant-dependent code.
Change-Id: I7dabe6ed7da7be640ed38c13aaaa096b8796d9a0
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/675
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These were deprecated in commit 69ac20a.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I047872f8cd61b42aaca6588ab75566219e4a3f5d
Reviewed-on: http://openocd.zylin.com/741
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add support for the new stm32f3x family from stmicro:
http://www.st.com/stm32f3
Change-Id: Icd1db95bb2767d9c0ecef24deefa92b4fdaa4f14
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/735
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updates the Kinetis NOR flash support to handle all known block and sector
sizes. Previously only 2kiB sectors were hard-coded, now all four known
combinations non-volatile sector sizes are supported.
The premise of separating Kinetis Program Flash (PFLASH) from FlexNVM is
also introduced. This means each "block" of flash (in Freescale terms) is
treated as a bank in OpenOCD. Correspondingly, the existing board
configuration for the TWR-K60M512 eval system is updated to recognize two
banks instead of one.
A board config for the TWR-K60F120M is also added.
Bank and sector erase and programming has been checked with both of the
mentioned eval boards.
Change-Id: Iae2d10ebf8f548d0a3698df5430bbbe1ccadc58a
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/663
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems like an esthetic change, but it will allow easy support for
other lpc17xx devices.
Change-Id: I2cb953ce1afdd82f6ca65b38d5557a28416f895e
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the Sony Ericsson J100I Phone to the board configurations.
Change-Id: I083ddf067c8ecdfdda0404fe9e9df980dbb86fe8
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/631
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the TI Calypso CPU to the configuration files.
Change-Id: Ieb462960391c4a2c630d7a83699c3b6e8162ace9
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/630
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These events have been deprecated for a number of years, update any
remaining scripts to the new events.
Change-Id: Ic31ff388545ac8b3a500045699ca92c541b13f12
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/634
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
now it is supported.
Change-Id: Id3b2ca9a2270974a5f453323f9057ecece400c94
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The smallest stm32f0 has 4k sram, so use this as the default.
Change-Id: I9097be9608da92b1b9da504e5bacc1280c86907a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/603
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The busblaster.cfg was contributed on April 23, 2012 and is a
duplicate of dp_busblaster.cfg that was contributed on Oct. 23,
2011. Therefore, deleting the second version. Also, renaming
the original dp_busblaster.cfg to simply busblaster.cfg, as this
name is more concise.
Change-Id: Iccb1f10f53dbbb248b1ff4c6295eaf67c32247c1
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/622
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The newer versions of BeagleBone boards use the default vid/pid
pair for FT2232 debugging. Please see the following README:
http://beagleboard.org/static/beaglebone/latest/README.htm
On revision A3/A4 boards, the VID/PID were chosen to match the
TI XDS100v2 (0x0403/0xA6D0). On A5 and newer revisions when we've
given the authors of CCS the chance to update their software, the
generic FTDI VID/PID (0x0403/0x6010) will be used to simplify
installation of drivers for systems already having those drivers.
Change-Id: I44228eb2029162f23d084eb05bcfef39e615668d
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/619
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The working area used in the config was incorrect, we only have 8K on this
board not 16K as the original cfg was declaring.
Change-Id: Ie0309fb86d839bd3bc1ac9383905b581fac5c388
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/598
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This enable the user or board config to override the parameters
passed to stm32_stlink.cfg.
Required to fix a incorrect working area bug with the stm32vldiscovery.
Change-Id: I40a4f7913ff37d577d44b1f23befccf0317080a1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/597
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
reset_config is now supported by stlink, remove from the config as this
is a per board option.
Change-Id: I85208d2154502b8d3a098afe1d9a28d75820a7c0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/582
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a FT2232 based USB JTAG dongle
Change-Id: Ibed773a23b6446df62fe4eac16c27fb2d741f4c3
Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-on: http://openocd.zylin.com/589
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use one board file per eval board, so that the filename matches the
exact board the user has / wants to use. Merging different boards into
one file is confusing.
Change-Id: I7c50233924a87a913723d7215c4851039c2971bc
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/566
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add initial TCL support for the pandaboard-es which is
based on the omap4460 from Texas Instruments.
Change-Id: Ic63588721487feb95e7cb3d41cfaab0d2f181766
Signed-off-by: David Anders <danders.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/573
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
this patch adds the initial support for the omap4460 es1.0
version which is similar to the omap4430 and used on the
pandaboard-es.
Change-Id: If885f7d9f8809929bd799786b539e4f499fa3478
Signed-off-by: David Anders <danders.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/572
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
* Added support to the FT2232 driver for the FT2232H-based
Digilent HS1 adapter.
Change-Id: Iab6cc15f299badaf115615b5d4d785ecb2273c27
Signed-off-by: Stephane Bonnet <bonnetst@hds.utc.fr>
Reviewed-on: http://openocd.zylin.com/558
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for the KaRo TX25 module on a StarterkitV base board.
For board details, check http://www.karo-electronics.com/tx25.html
Change-Id: I2c80c5467bc476955b55196728aa3c37c8185e6c
Author: Simon Widmer <simonxwidmer@gmail.com>
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Reviewed-on: http://openocd.zylin.com/557
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a digital oscilloscope which uses a Samsung S3C2440 internally.
http://randomprojects.org/wiki/Voltcraft_DSO-3062C
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Change-Id: I5e28c3a8f30665a162e34c831294e4e658a16ebb
Reviewed-on: http://openocd.zylin.com/548
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This adds support for the STM32F4 target and the STM3241G Eval Board, in
both standalone and using the onboard STLINK.
Change-Id: I62f8908b5880568b2b36c78a78f94c40861ff335
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/540
Tested-by: jenkins
The SAM3A/X processors that were released thus far is either
a SAM3A/X(4) - 256K, or a SAM3A/X(8) - 512K device. Thus
the config files are per variant, and not per device.
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Change-Id: I84d26d044e810eb428b1d6287907ea3bf8364c73
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/522
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Chris Morgan <chmorgan@gmail.com>
Change-Id: I082b0d3092c7f3b2ee6b68af64d48c78b31f1dbf
Reviewed-on: http://openocd.zylin.com/510
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Spencer Oliver
Franck Jullien
Andrey Yurovsky
Paul Fertser
Robert P. J. Day
Alex Murray
Sergey A. Borshch
Nemui Trinomius
Sergio Chico
Greg Ungerer
Pushpal Sidhu
Brad Riensche
Sergey Alirzaev
Marek Vasut
Laszlo Papp
Andreas Fritiofson
John Szakmeister
Giuseppe Barba
Ryan Corbin
Hsiangkai Wang
Ben Nahill
Peter Dietzsch
Salvador Arroyo
Rodrigo Melo
Vladimir Zapolskiy
Mathias K
Johan Almquist
Roman D
is2t
Gianluca Renzi
Peter Stuge
George Harris
Marc Reilly
Freddie Chopin
Aurelien Jacobs
Andrew Karpow
Vandra Akos
Joerg Fischer
Tom Rini
Christopher Kilgour
Bill Traynor
Olivier Schonken
Allen Martin
Uwe Hermann
David Anders
Stephane Bonnet
Wjatscheslaw Stoljarski (Slawa)
Simon Widmer
Chris Morgan
Jan Dakinevich