Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I984d2018f7d47a1042f1e12894563154fa7b566c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2196
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The signal names are changed for consistency with TI's docs and
sources.
Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137
Signed-off-by: Matthijs van Duin <matthijs@rinnic-vaude.nl>
Reviewed-on: http://openocd.zylin.com/2231
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Initial Support for AT91SAM7A2 on Olimex SAM7-LA2 board.
The board seems not to be able to reset into halted mode, as srst is
connected to NRESET of the cpu (configured srst_pulls_trst).
JTAG RCLK is connected to CLK.
Tested with interface/ftdi/olimex-arm-usb-ocd-h.cfg.
Change-Id: I2bdd67e3683e45f1119c5850bad294aa107891d8
Signed-off-by: Arne Wichmann <arne.wichmann@gmail.com>
Reviewed-on: http://openocd.zylin.com/2318
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The F334 disco board has a stlink V.2-1 as F3 nucleo boards. Normal F3 disco
boards use stlink v2 and can't ne used.
Change-Id: I77ebef93b184592f25ff18bb2da776d636f60ff0
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2434
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds configs for Alphascale asm9260t ARM based SoC and
Evaluation Kit based on this chip.
Change-Id: Id8d3a1ef204e3ae84540c2693e3d62650ba82f73
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2515
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The flash definition belongs in the target cfg. Add some working area
and suitable reset_config.
Make kx.cfg more similar to klx.cfg.
Disable rclk as it is dead slow and a fixed 1MHz clock seems to work.
Change-Id: I8328f179c3a33be64403da93616abb48651bdfe6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2227
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Configure the LED to be off by default, blink on activity.
Change-Id: I8515ee66c49bddf866268b85811be15c2dbc086c
Signed-off-by: Anton Kuzmin <anton.kuzmin@cs.fau.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2539
Tested-by: jenkins
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the board to the list of supported devices for the easy
recovery procedure. Only ram_boot is supported for this target.
Change-Id: I144e1836f8b6257e96a42c98c2668da74ce243f6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2520
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Add configs for Atheros ar9331 MIPS based WiSoC and
board based on this chip: TP-LINK TL-MR3020
Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2519
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.
These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.
The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.
Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds support for Silicon Labs (formerly Ember) EM357
and EM358 chips and derivatives.
Change-Id: Ie63aed95a2f4ef1a6b955e301a51b4de1b3a5462
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2470
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds a trivial config for LPC8xx chips based on the already
existing infrastructure in lpc1xxx.cfg.
Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2464
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Added support for the ST nucleo l152re board with a stm32l152ret6 MCU,
analog to st_nucleo_f* configurations.
Change-Id: Id2c61dc7a7cb2e1cc64442191b367bab4247bdeb
Signed-off-by: Thomas Eichinger <eicht@lepus.uberspace.de>
Reviewed-on: http://openocd.zylin.com/2489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It depends on the particular target whether it can work with SRST
asserted or not, so this belongs to the target config rather than the
board config.
Also, this allows for simple
openocd -f myboard.cfg -c "reset_config connect_assert_srst"
command to be used whenever a user feels a need to connect to an
unresponsive target.
Change-Id: I3d8da9ae47088fc0c75a20bfdd20074be1014de0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2459
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
So remove it from all the configs, it's misleading, and leads to cargo
culting of config files.
Change-Id: I2b77e60d5e96f9759c7c9fc91b20e73be2e95d9a
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is an integrated adapter used on the IoT-LAB boards.
Schematics are available from
https://github.com/iot-lab/iot-lab/wiki/Docs/openm3-schematics.pdf
Change-Id: I1c80e72653c3f319bb04d01e3dfddb1c2447c398
Tested-by: Quentin Lampin <quentin.lampin@orange.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2415
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It is derived from ti_tmdx570ls31usb.cfg, using a different TAP ID.
Change-Id: I2d911995c76ea4f75a780cc230d61f4959825809
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2440
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should have been corrected earlier with the split of l1/l0 code
apart.
Change-Id: I87b94a310ae7e76318554a9cd2705348a942d58b
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2447
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
commit b5a6ba46 broke the following board files, update to new cfg.
Change-Id: Ic3b776bd32eb72eae6ad1e130e329268ce9ba71a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2384
Tested-by: jenkins
L0 is cortex m0+, so different id codes, SWD only, different addresses
for the clock speedup. It has no endian options, no boundary scan.
Removed all L0 specific portions from L1 files, and renamed files to clarify
their purpose. The deprecated stm32lx_stlink.cfg is kept as is, as it is only
around for backwards compatibility with prior releases.
Tested on STM32L053 Discovery and STM32L151 Discovery.
Has _not_ been tested with jtag on L1.
Change-Id: I8eea890d2f92a302d9e9c8a8832d218ee1b6bcfc
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Fix script parse error, when using JTAG, introduced in
commit 0187ced9ed
Add several BS TAPIDs with comments about ST documentation.
Change-Id: I8d0370b244ccaf7ea0dbe1919bfad1915f7317d4
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-on: http://openocd.zylin.com/2376
Tested-by: jenkins
Reviewed-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since all F4 parts have an internal HSI providing 16MHz, it's safe to
use 2MHz JTAG frequency by default.
Change-Id: I2702d5a1d642d4acd4af2db54c028949132c6900
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2383
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this board use STLink-V2-1, the STM32L1xx use the STLink-V2.
Change-Id: Ie58f45affcb1e9a6fed711b48c3c03b5035ab2b2
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2317
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add CPUTAPID for stm32 L0xx mcu devices. Using -expected-id to
add the new id with the id for L1xx devices. This for reduce the
duplicated code.
Change-Id: I48bd230884ecf38fa200c620b547bdf3b5f59132
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2315
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to my inspection of an Olimex ARM-USB-OCD-H adapter ACBUS0
is connected directly to an SN74LVC2T45 buffer input B2, and the
corresponding output A2 is connected directly to the JTAG
connector. It seems the information in the Olimex flyer is incorrect
for the -H version and TRST can't be tri-stated, ACBUS2 is unused.
The older ARM-USB-OCD device has SN74AC244 for an output buffer and
ACBUS2 controls its !2OE, ACBUS0 connected to 2A1 (2Y1 is nTRST), in
accordance with the information flyer.
Change-Id: I22828b7b959b6f62c3f51367feb8fab9705641e5
Reported-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2286
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tim Sander <tim@krieglstein.org>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Fritiofson
Matthijs van Duin
Uwe Bonnes
Nemui Trinomius
Arne Wichmann
Paul Fertser
Oleksij Rempel
Anton Kuzmin
Andreas Bomholtz
Angus Gratton
Joerg Fischer
Pawel Si
Jacob Palsson
Ed Beroset
Heinz Schweiger
Tomas Vanek
Thomas Eichinger
Karl Palsson
Andreas Färber
Spencer Oliver
Karl Palsson
Juha Niskanen
Rémi PRUD'HOMME
Austin Phillips