The breakpoint/watchpoint message was wrong for Feroceon and
Dragonite, which have only one working watchpoint unit.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Summarize most ARM11 and Cortex-A8 updates as "acting much more
like other ARMs", and mention code sharing.
Clarify a few other points, including support for "reset-assert"
on all ARMs except Cortex-M (which doesn't exactly need it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This fixes a bug whereby GDB's breakpoints weren't activated.
The root cause is a confused interface to resume(). Fix by
almost ignoring the "handle breakpoints" parameter; it only
seems related to the case of skipping breakpoint-at-PC.
Update a few coments to clarify what's happening.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Doxygen: don't be needlessly verbose; alphabetically sort members
TODO: add random bits; clarify which manuals are referenced
ARM disassembler: mention a few opcodes that still aren't handled
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Highlight the needs to properly jumper development boards; to
make the OpenOCD configuration match the jumpering; and to have
a usable "reset-init" method when debugging early boot code.
Specific mention of the "ATX Mode" that seems useful on
many i.MX boards, forcing NAND boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update the comments about DP registers and some of the bitfields.
Remove inappropriate (and unused) DP_ZERO declaration.
Add some (currently unused) #defines needed for SWD protocol support,
based on previous patches from Andreas Fritiofson and Simon Qian.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
If GDB halts unexpectedly, print reason: srst assert or power
out detected.
If polling fails, then things are a bit trickier. We do not
want to spam telnet or the log with polling failed messages.
Leave that case be w/a comment in a code for now.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Rather than issuing a halt and then stepi/resume, just
wait for target to halt.
Issue a sterner warning via gdb console that any gdb
register changes will be ignored in this case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The "cm3-ftest.cfg" can be used to verify that OpenOCD handles
certain faults correctly:
- Test #1: it ignores faults that it wasn't told to catch
- Test #2: if vector_catch is told to catch, it catches
The "fault.c" generates ASM code to trigger faults, while the
config script loads and runs pre-compiled code.
This covers most, but not all, of the vector_catch options.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't give the same names to both flash chips on two OMAP boards.
For OSK, enable DCC downloads (removing a warning).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report each region of same-size sectors separately, instead of
incorrectly reporting that every sector has the same size.
This is a longstanding bug on NOR flash chips with non-uniform
sector sizes. It was largely hidden by other bugs in flash
handling. When some of those were recently fixed, this one was
exposed as a regression on str710.
[oyvind.harboe@zylin.com: update the loop to behave on str7 ]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
openocd does not start with the target configfile due to the case in the
dependent config file.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make the test case easily adjustable in size. str710
has very peculiar flash sector layout, nice for testing,
but a larget test_rom.elf is required.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Skip over a bkpt instruction if found on resume/step.
Only software breakpoints known to OpenOCD are currently handled.
So this handles the special case of either a user added bkpt
or library added, eg. semi-hosting support.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Folk almost certainly want to have OpenOCD compute the checksum
when they modify the vector table. However, that almost guarantees
that "verify_image" will fail.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Put the memory map logic into its own subroutine.
This will make it a bit easier to package bugfixes,
and simplifies the query packet handling.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make most methods static; net minor object code shrink.
Likewise various data symbols; no net change.
Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The default script search path on Windows is out of date with
the current layout (from installation and documentation), which
makes the standard script library not be found after a normal
./configure && make && make install
under msys/MinGW. The same should hold true for cygwin native builds
(not verified).
Update search path to ../share/openocd/scripts not ../lib/openocd,
relative to the openocd executable.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "NOR: last_addr also needs correction when checking alignment"
patch omitted a necessary update to the key diagnostic; fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It is conceivable that there could be commands in the
queue when a speed change request comes in. Flush the
hw queue before changing speed. Not observed, found by
inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
According to OpenOCD error handling rules the error is
logged at where it occurs(same site where an exception
would have been thrown).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The very first command after init command should be "read target voltage".
This is a tweak for the Old Versaloon firmware. Without this, in most
most cases, it works. Under Ubuntu9.04, there is a chance that the USB
will fail. The problem disappears if I read target voltage first.
For the lastest Versaloon firmware, it's OK.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The LPC3180 NAND driver was crashing on some large page chips.
Fix:
- Crash and related functionality (don't memset too much OOB data)
- Some debug messages
- Command handling now works
[dbrownell@users.sourceforge.net: whitespace/linelength/message cleanup]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't just complain about an invalid ACK; say what the
value was, to help troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Until we manage breakpoints at runtime (patches not ready for 0.4)
the only way this code should touch them is to disable them at server
startup (a previous debug session may have left them active).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add doxygen and other comments for what's more or less the lowest
level JDAG-DP primitive, to access JTAG_DP_{A,D}PACC registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Teach most remaining ARM cores how to use the "reset-assert" event.
Same model as elsewhere: iff a handler is provided for that event,
use that instead of trying to assert SRST (which may be unavailable,
or inappropriate since it resets too much). Else no change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).
Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Using the erase bank command will cause a time out error. Replacing
this with the erase sector bank will provide a slower but safer and
stable method to erase the flash.
Signed-off-by: Laurentiu Cocanu <laurentiu.cocanu@zylin.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Shrink some overlong lines. Add my 2009 copyright.
Move a declaration to the beginning of its block.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Capture various bits of useful information that have come up on the
list but haven't yet gotten into the documentation:
- Watchdog timers firing during JTAG debug need attention;
- Some chips have special registers to help JTAG debug;
- Cortex-M3 stepping example with IRQs and maskisr;
- Clarifications re adaptive clocking: not all ARMs do it, and
explain it a bit better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates three aspects of debugger/exception interactions:
- Save the user's "vector_catch" setting, and restore it after reset.
Previously, it was obliterated (rather annoyingly) each time.
- Don't catch BusFault and HardFault exceptions unless the user says
to do so. Target firmware may need to handle them.
- Don't modify SHCSR to prevent escalating BusFault to HardFault.
Target firmware may expect to handle it as a HardFault.
Those simplifications fix several bugs. In one annoying case, OpenOCD
would cause the target to lock up on ome faults which triggered after
the debugger disconnected.
NOTE: a known remaining issue is that OpenOCD can still leave DEMCR
set after an otherwise-clean OpenOCD shutdown.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
DCC downloads should be enabled for any self repecting
openocd config file for arm7/9. Print out note about
it otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Allow targets to run checks post reset. Used to check
that e.g. DCC downloads have been enabled.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
David Brownell
Øyvind Harboe
Edgar Grimberg
Spencer Oliver
Michael Grzeschik
Andreas Fritiofson
simon qian
richard vegh
Peter Korsgaard
Laurentiu Cocanu