The pflash.0 bank should not be present as it overlaps with
the flash bank created by target/kx.cfg, triggering an error.
This is also in line with the existing twr-k60f120m.cfg.
Change-Id: I5f620e01319d967f12e029fb6865ccdd031713b3
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3108
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
16000kHz is only safe after PLLs have been locked
properly. Until that's done (with reset init), we
can only safely run at 1000kHz.
Change-Id: I4e0a17e88aa9919cd6c34d44da68e23115c0d3a3
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/3015
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added interface config file for the FTDI FT232H based UM232H module.
This should work with UM232H-B too, an even cheaper module, but
that has not been tested.
Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251
Signed-off-by: Ragnar Sundblad <raggesu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3031
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I232d769d893d54e4ea9411c46c56b19587b69919
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2707
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with cmsis-dap using the EDBG chip on the board.
Change-Id: I3d398685c81e4701a9f6c1a66e60f7a87f839daa
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/3092
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New configuration for NXP LPC4370 which consists of a Cortex-M4
and two Cortex-M0 cores.
Change-Id: I9918e3ff33218a14a99e4bbab9dce2e7b45b4d96
Signed-off-by: Jim Norris <u17263@att.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2124
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This reverts commit 7d7a43fd36.
The change concerns the "Black" variant of the TI BeagleBone, while the
configuration file is for the original BeagleBone board, which actually
embeds a debug interface on the PCB.
Change-Id: I2232af210deb698f8b3c0a547f26cd0a0a8f89d0
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3094
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: La Fonera FON2200
Change-Id: Ibfdbfc9c2beca6cf436c9ee5e493b08bfb55ac85
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2839
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: Netgear WP102
Change-Id: Id93957b5d5851a272f15be35f9f448a9ce6d8a08
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2835
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since 2cbbe9a it was actually decreasing the configured work area size.
We could now do "set WORKAREASIZE 0x2000" before sourcing lpc4350.cfg,
but there seems no point in doing so. Simply drop the configuration here.
Change-Id: I25b9dbbc007ba652b66099832198b7c329929858
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3086
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Default to lpc8xx as before, but allow setting the actual CHIPNAME.
Change-Id: I5a48fa75c640440a0d4c3f2858653e94bed846d2
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3084
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Board files should not select the interface. The BeagleBone Black is not
limited to just one JTAG interface.
Change-Id: I71ccc3dd9e2ca331a436701fab04e548b0abf829
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3083
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Adapted from diolan_lpc4350-db1.cfg. Both boards are identical except
for the SoC, so keep them in sync.
Change-Id: If892d8e953b0e3a9209a95b3b23a547357c10b7a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3038
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reuse the flashless LPC4350 as base and amend it as necessary.
The LPC43x7 have 2x 512 KB of flash.
Change-Id: Ia7ffbc7101023479971984b839f171ed4be6b089
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3037
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add support for the JTAG TAPID found on SK-FM4-U120-9B560-MEM V1.1.0 board.
Change-Id: Idbfe28927e0c549f0c89c29904d23971281927c9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3039
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It is found on the SK-FM4-U120-9B560-MEM V1.1.0 among others.
Change-Id: I4c708c9391e954cbbc8d0860a2a2dbd264aea865
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3008
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Its memory layout is different from MB9BFxxx.
Change-Id: I39c9f9cf582cd182971a9f83bb88c7a18da6cf15
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3007
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The xCORE-XA Core Module board has an XS1-XAU8A-10 SoC with 8 xCORE cores
and one ARM core. This config is for the ARM Cortex-M3, via J-Link OB.
Tested with "J-Link OB-STM32F103 V1 compiled Feb 5 2014 13:48:52".
Change-Id: Id7fadf8f323b45d5cfc0cae1054bd7b916771d6a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2763
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The XS1-XAU8A-10 has 8 xCORE cores and one ARM core.
This config represents the ARM Cortex-M3 core, which is apparently
Silicon Labs EFM32 Giant Gecko IP.
Change-Id: I998360f096c759d2e274d96c1ca2e0450ba61146
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2762
Tested-by: jenkins
Reviewed-by: Oleksij Rempel
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Most Xilinx FPGA devices contain an embedded, unique device identifier
called the "Device DNA". The identifier is nonvolatile, permanently
programmed into the FPGA, and is unchangeable providing a great serial
/ tracking number.
Debugging was done in https://github.com/timvideos/HDMI2USB/issues/36
Change-Id: Iad03eafb40887f0321a4dc22858a7c3bf37a12b3
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2960
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Another board supported by the ixo-usb-jtag project.
Change-Id: I676197c64e208886bc03d1bafcc964ef1fc2160b
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2963
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The board is supported via the ixo-usb-jtag firmware.
Change-Id: I1e8a5ead850c0843b8532a5b54a7e7117778278e
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2962
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also add further documentation about the project and how to use it.
Change-Id: Ia9878de566b3c8c1ea29f129287d5aea904d861d
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2961
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Flash driver "mini51.c" and "nuc1x.c" are same target MCU.
This patch integrates each driver and functions,
and makes into new "NuMicro" flash driver.
Change-Id: Ifff5c1cfdd265acca0f489631695be9194fa144c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A target config and a simple flash driver for the ADuCM360 microcontroller.
The EEPROM of the chip may be erased and programmed.
Change-Id: Ic2bc2f91ec5b6f72e3976dbe18071f461fe503b8
Signed-off-by: Ivan Buliev <i.buliev@mikrosistemi.com>
Reviewed-on: http://openocd.zylin.com/2787
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Tested with Porcupine-1 JTAG adapter board and Digilent JTAG-HS3 interface;
reset does not yet work, pending nSRST configuration of the interface used.
Change-Id: I0d0679e098d93ffbd1539004cdb900e2a8ae4a25
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2730
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As found on the Parallella-I board SKU A101020.
Change-Id: Ie7e7a36325926d67fbe555b46a9be8a74fac8dba
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2729
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Derived from tcl/interface/digilent-hs1.cfg.
JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with
PS_SRST_B on Xilinx Zynq SoC.
Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2728
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the chip IDs corresponding to the new 5V "SAMC" parts which are
otherwise identical to the SAMD and should work with this driver. Also
add the configurations for their Xplained Pro boards.
Change-Id: Ic268d4ac384a3a77d4211a94da9f9faf4d8c0f7b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2809
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Pipistrello is a low cost FPGA board with a Xilinx
Spartan6 LX45, a SPI flash and onboard FTDI JTAG.
This board is a good example use case for the jtagspi
flash driver talking through a proxy bitstream.
Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2846
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This covers only the Cortex-A5 for now, not the Cortex-M4.
Change-Id: I739ec52b14b83d6e9f124ed61f8941502e481402
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2766
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>