add "mrb" command to read a byte of memory into a variable
Change-Id: I5ddc9fbcc55958a249548627bd15824df6dc0d61
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3542
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Some installations of OpenOCD are used in restricted environments that
do not permit binding to public interfaces.
This patch does not affect the default behavior to listen on all
interfaces, however it does give the option to restrict services by way
of the bindto command.
Change-Id: Id51bd64b376a8c62dd47b08b4d834872925e6af2
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3534
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Today the reset option for connect_assert_srst is not done for SWD.
This patch adds this to SWD and make it possible to connect to targets which might disable JTAG interface when running.
Change-Id: Ib89f7cf59b628e8f0b5fca9dd9e362e383c4b99f
Signed-off-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-on: http://openocd.zylin.com/3018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the 'data_swap' parameter to the CFI driver, which enables
swapping of data bytes when writing/programming words to the flash.
Note, that this specifically means that bytes are not swapped when
writing command words to the flash chip. Unless you are using the SAP
in an LS102x chip to program an attached 16-bit NOR flash, you hopefully
do not need this!
Change-Id: I1e6f7169da36f373c880d1756d9c21c9957acc50
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3109
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The SAP in LS102x SoC's from Freescale is able to read and write to all
physical memory locations, independently of CPU cores and DAP.
This implementation is 100% based on reverse-engineering of JTAG
communication with an LS1021A SAP using a JTAG debugger with SAP support.
And as such, this code is for now "works-for-me", pending verification
by other OpenOCD users, or even better, actual information from Freescale
on the SAP interface.
Change-Id: Ibb30945e017894da5c402f9f633fc513bed4e68c
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3096
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv4_5_crc.inc, and convert the code to target
endianness the least intrusive way.
Change-Id: I7452b2c7e679dae14f9cda5f89bc81c16fc12cad
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3473
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Add rules to build armv4_5_erase_check.inc, and convert the code to
target endianness the least intrusive way.
Drop an unused word from the assembler sources to make the ARM bytecode
fully match that of armv4_5.c and to not break ARMv4 assumptions.
This completes the build rules for contrib/loaders/erase_check directory.
Change-Id: I36be7a944e26142088195fa3fb072d4e577bf328
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3135
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv7m_crc.inc and include it via preprocessor.
Change-Id: I4482c7acb8454de28bdf210d9f06c0720ada490a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: Ie3f95f992a98a1325428e4032a1c17346d4c9977
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3472
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: I95bb12fbe7c80b594e178468bcd4f6387c682c93
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3471
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Andreas Fritiofson says "If any adapter driver does not work with
arbitrary lengths of individual fields, it's a bug."
https://sourceforge.net/p/openocd/mailman/message/35091945/
Note also that lengths of at least 96 bits are already in use, eg. in
mips_ejtag_add_scan_96().
Change-Id: I62a150adc75c0ef78827683ca8d0a8e90310a982
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/3491
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Just like observed with the General App Kit earlier, it now started to
fail halting:
SWD IDCODE 0x2ba01477
TARGET: xmc4500.cpu - Not halted
in procedure 'reset'
in procedure 'ocd_bouncer'
SWD IDCODE 0x2ba01477
Halt timed out, wake up GDB.
Rely on the target's default sysresetreq behavior to allow flashing to
work seemlessly again.
Change-Id: Ib9ce5f2c0ab99dca6d0fc74435fe26a58437fae5
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3416
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Upstream commit
http://git.savannah.gnu.org/gitweb/?p=config.git;a=commitdiff;h=f4ebd3ed097771a729b68e688236aea665e7c1f3
makes both i386 and amd64 MSYS (and MSYS2) systems be detected as
*-pc-msys .
With this patch OpenOCD builds without any additional tweaks on MSYS2
with the latest config.guess.
Change-Id: I1ae4154f76125a84078926b425fa989904639ce0
Reported-by: "Stevens, Kelly E. M." <Kelly.Stevens@gtri.gatech.edu>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3468
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
When using SWD rather than JTAG transport, the lpcspifi driver complains:
Error: Device ID 0x0 is not known as SPIFI capable
Error: auto_probe failed
This is because target's JTAG tap->idcode is zero for SWD.
Drop this check completely and hardcode the addresses for now. Neither
the JTAG TAPID nor the SWD IDCODE are unique enough to detect the exact
chip model and thereby its memory map.
Change-Id: Ic230e3e989a3e1f1a5b3bae68bdb34e5ef55d392
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3089
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested with TI MSP-EXP432P401R LaunchPad, via both on-board XDS110-ET (swd)
and external J-Link (jtag).
Change-Id: Ic0caa8516a155754b1c88a04acc8d3c511d9a5f7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3485
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The current configuration leads to the following error when trying to
program the target:
SWD IDCODE 0x2ba01477
timed out while waiting for target halted
TARGET: efm32.cpu - Not halted
in procedure 'program'
in procedure 'reset' called at file "embedded:startup.tcl", line 478
in procedure 'ocd_bouncer'
Use the default reset handling of the target (SYSRESETREQ) to reset the
system rather than SRST to fix the problem.
Tested on EFM32GG, EFM32TG and EZR32WG STK.
Change-Id: I788c41baf08b20814cbe0934b563424c4bc144b8
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3420
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change type of use_raw to boolean. This parameter was already
assigned a boolean variable (in COMMAND_PARSE_ENABLE) and used
as a boolean.
Change-Id: I22f8308246cb25ec9ec2395599e406160410a2a8
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Reviewed-on: http://openocd.zylin.com/3496
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Return ERROR_NAND_DEVICE_NOT_PROBED to prevent calling functions
from segfaulting when nand device has not yet been probed (ie nand
verify)
Change-Id: Ibc4da0aad00e6cc6c83008882b054d981453dc36
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Reviewed-on: http://openocd.zylin.com/3495
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Both the STM32F429I-DISC{O,1} boards are equipped with the same MCU, but
differ by the debugging chip:
- the STM32F429I-DISCO uses the ST-LINK/V2 chip;
- the STM32F429I-DISC1 uses the ST-LINK/V2-B chip (which matches the USB
VID/PID set in stlink-v2-1.cfg).
Change-Id: I07d637f72d26cf5d714472638da974eb6ca02325
Signed-off-by: Samuel Martin <s.martin49@gmail.com>
Reviewed-on: http://openocd.zylin.com/3492
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Memory accesses are not made through the APB-AP, they are made through
the CPU (which happens to be controlled over the APB-AP). Rename all
irrelevant uses of the APB-AP term. And fix the long standing typo in
the function names...
Change-Id: Ide466fb2728930968bdba698f0dd9012cc9dbdf9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3216
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
According to the MSP432P4xx Family TRM (SLAU356A) Figure 4-7,
0x9AF is the part number for MSP432P401xx devices.
Verified on TI MSP-EXP432P401R LaunchPad.
Change-Id: I22b57c42f2a0dc8263fab6b480cf8c169c7dc295
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3486
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This was found on multiple XMC4500:
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00001c11db
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1db, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
On multiple XMC4700 and an XMC4800 this was found instead:
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00001c11df
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1df, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
Name them "XMC4500 ROM" and "XMC4700/4800 ROM" respectively.
Change-Id: If369a6d16524004ba439b878f090a313a9f3a760
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3482
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Not documented in the Reference Manuals but found on multiple XMC1100/1202:
Valid ROM table present
Component base address 0xf0000000
Peripheral ID 0x00001c11ed
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1ed, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
Name it "XMC1000 ROM", since it didn't differ between XMC1100 and XMC1200.
Change-Id: I98a5a524c0d0836f395400fbac24fd496b2ec141
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3481
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
ulink_calculate_frequency() is used exclusively when
_DEBUG_JTAG_IO_ is set, no need to compile this
function if it is not used.
Declaring it static in the same commit.
Change-Id: I243ffdf69a1dc3bee6d16e4bb8d78396b6ea5144
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3241
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The original ULINK adapter has been introduced by Keil in 2002 and got
replaced in 2008 by the incompatible ULINK2. It is not listed on their
website any more. For information about it, browse archive.org
for http://www.keil.com/ulink1/ or http://www.keil.com/ulink/
Change-Id: Ie52d381580acab53ddb40499594dbdc2d27ef1b6
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3371
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Consistently increase the space-indentation of the .full values to
nicely align with the new "Qualcomm QDSS Component v1" .type value.
Change-Id: Icd28d8f3fc7c3afcccb9dcfe138ac57d64927d1a
Suggested-by: Freddie Chopin <freddie.chopin@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3480
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Note:
WCR (Wire Control Register) is replaced by DLCR (Data Link Control
Register). And only TURNROUND field is modifiable.
[andreas.fritiofson@gmail.com]:
Rename DP_IDCODE to DP_DPIDR as well.
Sort list by address and align it using spaces instead of tabs. Add
comments about supporting DP versions.
Remove non-functional wcr command completely.
Change-Id: Ic6b781b07c8eead8b0237d497846d0da060cb1ba
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3244
Tested-by: jenkins
Commit dfc6658cf9 ("Kinetis: flash
driver described in openocd.texi") inserted a kinetis section between
fm3 and lpc2000. Then commit 43ff5acd45
("flash: New Spansion FM4 flash driver") was merged, inserting the fm4
section between kinetis and lpc2000, instead of after fm3. Finally
kinetis_ke was added between kinetis and fm4 in commit
5396ec5dcc ("flash: Added support for
Freescale Kinetis KE family.").
Restore the alphabetical order by moving the fm4 section to before
kinetis.
Change-Id: I77e47c3cd5b2cd8570b62ff2f7be8526aaf57ad0
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3484
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Instead of placing Atmel last, after ANY_ID, place it after ARM (it's
arm_adi_v5 despite 0x4BB) and sort it with the other vendors, i.e.
before ADI and Qualcomm. Adapt column alignment.
Drop the redundant "Atmel" comment to clarify that Analog is not Atmel.
Change-Id: Ic06785db079cf58d49815a639236636c180e5e17
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3479
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On APQ8016 was found a CoreSight component designed by
Qualcomm, according to db410c HRM [1] it has a partnumber
following this schema:
[11:8] is 0x4 meaning Qualcomm designed Coresight component in QDSS. Reads as 0x4.
[7:6] is Subsystem/core family ID (e.g. denote QDSS family or generation).
[5:4] is Subsystem/core configuration options (e.g. denote cache options, etc.).
[3:2] is Subsystem/core fuse options.
[1:0] is Subsystem/core future use field
Reads as 0x440.
[1] - https://developer.qualcomm.com/download/sd410/hardware-register-description-qualcomm-snapdragon-410.pdf
Change-Id: I9b4b41fd17c59d2f5ae35b53278d06d6087665f8
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3408
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On hi6220 'dap info' returned some unknown components from ARM.
Collected from ARM docs, mostly ROM table entries.
Typo fix for Cortex-M3 FPB.
Change-Id: I96bbf7349061937b3afc8bb8d6d1650f2609f82d
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3407
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Initial release of Ambiq Micro Apollo flash driver
supporting our sub-threshold (low power) Cortex M4F part,
and Evaluation Kit.
We have been shipping openocd to our customers for about one year.
The EVK boards are SWD only using ftdi. We also use two of the
other COM instances to display debug information.
It takes about 15 seconds to flash 512K, and mass erase is
about 5 seconds.
Tested by internal verification group, FAE's, and customer sites.
Merged commit 'refs/changes/17/3417/1' as suggested. Makefile.am
and drivers.c follow the new format to avoid conflicts.
Removed unused fault_capture command.
Added documentation for flash driver.
Change-Id: Iae92d869369c6827244f0071f9cb522d8d91fed8
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Reviewed-on: http://openocd.zylin.com/3230
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Clean up working area in case writing fails. Probably inherited from
armv7m_blank_check_memory(). Fix adapted from armv7m_checksum_memory().
Change-Id: I784bef481d1eba833ab6a9c34249fe9d43a16081
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3470
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Clean up the working area in case writing fails.
Adapted from armv7m_checksum_memory().
Change-Id: I4e5950f568ed70a72a1dcfd77e3321110b17e1de
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3469
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Spotted by gcc:
arm7_9_common.c: In function ‘arm7_9_unset_breakpoint’:
arm7_9_common.c:353:4: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
if (current_instr == arm7_9->thumb_bkpt)
^~
arm7_9_common.c:356:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘if’
if (retval != ERROR_OK)
^~
The logic won't change once the braces have been added, as the new 'retval'
check only makes sense within the if().
Change-Id: I6a303e118f2150e5eb25c9268ad06de5d8a533b2
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Reviewed-on: http://openocd.zylin.com/3477
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Among other things, this fixes building on Cygwin and MSYS.
Change-Id: I8bdceb49dc72b5f666388cfd97876eba8e1d2b13
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3478
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The ioutil helper functions copyfile and copydir were last and only used
in ecosboard.c which has been removed with commit 39650e22.
Removing the dead code.
Change-Id: I36c7c4c5009d755b4513a14a9f9e214d1ee500e8
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3240
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The cortex_a specific assert_reset function must only apply nSRST if
the reset configuration states that JTAG can be used while nSRST is
asserted.
Change-Id: If604a65fdea5bcb46ec723ada547a4e8d6fa8c59
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3356
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
For STLINK_SWD_AP_FAULT git://git.ac6.fr/openocd commit 657e3e885b9ee10
returns ERROR_OK with the comment:
Change in error status when reading outside RAM.
This fix allows CDT plugin to visualize memory.
Change-Id: Id8e220961b748ef9467fd84de62b1dc84ace63f8
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3373
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Matthias Welwarsky
Steven Stallion
Fredrik Hederstierna
Esben Haabendal
Uwe Bonnes
Marc Schink
Andreas Färber
Tim Newsome
Paul Fertser
Ivo Manca
Samuel Martin
Andreas Fritiofson
Alexander Kurz
Jiri Kastner
Rick Foos
James Mastros
Aleksander Morgado
Robert Jordens