even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Doxygen: don't be needlessly verbose; alphabetically sort members
TODO: add random bits; clarify which manuals are referenced
ARM disassembler: mention a few opcodes that still aren't handled
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.
Add TODO list entry re full support for NAND/NOR bank names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It can invalidate ECC codes, and in general is not guaranteed
to work. (However on some chips it _appears_ to behave.) Just
don't do it; don't write in those cases.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove useless space/tab at end of lines.
Remove spaces in indentation and replace with tab.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The previous stuff was needed because the ARM11 code wasn't using
the standard ARM base type and register access ... but now those
mechanisms work, so we can switch out that special-purpose glue.
This should resolve all the "FIXME -- handle Thumb single stepping"
comments too, and properly handle the processor's mode. (Modulo
the issue that this code doesn't yet handle two-byte breakpoints.)
Clarify the comments about the the hardware single stepping. When
we eventually share breakpoint code with Cortex-A8, we can just make
that be the default on cores which support it. We may still want an
override command, not just to facilitate testing but to cope with
"instruction address mismatch" not quite being true single-step.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds basic autoprobing support for the JTAG scan chains
which cooperate. To use, you can invoke OpenOCD with just:
- interface spec: "-f interface/...cfg"
- possibly with "-c 'reset_config ...'" for SRST/TRST
- possibly with "-c 'jtag_khz ...'" for the JTAG clock
Then set up config files matching the reported TAPs. It doesn't
declare targets ... just TAPs. So facilities above the JTAG and
SVF/XSVF levels won't be available without a real config; this is
almost purely a way to generate diagnostics.
Autoprobe was successful with most boards I tested, except ones
incorporating C55x DSPs (which don't cooperate with this scheme
for IR length autodetection). Here's what one multi-TAP chip
reported, with the "Warn:" prefixes removed:
clock speed 500 kHz
There are no enabled taps. AUTO PROBING MIGHT NOT WORK!!
AUTO auto0.tap - use "jtag newtap auto0 tap -expected-id 0x2b900f0f ..."
AUTO auto1.tap - use "jtag newtap auto1 tap -expected-id 0x07926001 ..."
AUTO auto2.tap - use "jtag newtap auto2 tap -expected-id 0x0b73b02f ..."
AUTO auto0.tap - use "... -irlen 4"
AUTO auto1.tap - use "... -irlen 4"
AUTO auto2.tap - use "... -irlen 6"
no gdb ports allocated as no target has been specified
The patch tweaks IR setup a bit, so we can represent TAPs with
undeclared IR length.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
- Use the name mappings all the other code uses:
+ name-to-state ... needed to add one special case
+ state-to-name
- Improve various diagnostics:
+ don't complain about a "valid" state when the issue
is actually that it must be "stable"
+ say which command was affected
- Misc:
+ make more private data and code be static
+ use public DIM() not private dimof()
+ shorten the affected lines
Re the mappings, this means we're more generous in inputs we
accept, since case won't matter. Also our output diagnostics
will be a smidgeon more informative, saying "RUN/IDLE" not
just "IDLE" (emphasizing that there can be side effects).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Load the XScale debug handler from the read-only data section
instead of from a separate file that can get lost or garbaged.
This eliminates installation and versioning issues, and also
speeds up reset handling a bit.
Plus some minor bits of cleanup related to loading that handler:
comments about just what this handler does, and check fault codes
while writing it into the mini-icache.
The only behavioral changes should be cleaner failure modes after
errors during handler loading, and being a bit faster.
NOTE: presumes GNU assembly syntax, with ".incbin"; and ELF,
because of the syntax of the ".size" directive.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
- In the File List, these files are listed and link to empty pages.
- This patch adds @file blocks to reference the pages each file contains.
- Remove redundant "OpenOCD" from PATCHES title; it clutters the tree view.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1916 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Added questions regarding ideas on making tcl-less builds of OpenOCD
git-svn-id: svn://svn.berlios.de/openocd/trunk@1830 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Øyvind Harboe
David Brownell
Antonio Borneo
Uwe Hermann
dbrownell
oharboe
zwelch