This is based on the initial work by Paul Fertser with addition of the
switch sequences and new ACK handling. In case of WAIT response, the
sticky bits are cleared and the last operation is repeated. The ACK
handling is based on the interpretation of the 8 February 2006 ARM
Debug Interface v5 Architecture Specification
Change-Id: Id50855b1ffff310177ccf9883dc9eb0d1b4458c8
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2437
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I couldn't make OpenOCD to work with GDB. I was always getting this in GDB:
(gdb) target remote localhost:3333
Remote debugging using localhost:3333
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Malformed response to offset query, timeout
(gdb)
While debugging gdb remote protocol, I have seen that gdb responds with:
w ++$?#3f
And those two '+' seems to confuse the OpenOCD parser, if it sees another
'+' sign it emits the DEBUG output and sets the noack_mode to 2. The
problem is that we weren't even IN noack mode, this was set to 0 and then
it explicitly sets it to 2 and thus turning the noack mode on.
Change-Id: If267c9226e57fa83121ded09cf69829f8f0b4b93
Signed-off-by: Matej Kupljen <matej.kupljen@gmail.com>
Reviewed-on: http://openocd.zylin.com/2545
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Without this patch, to perform a memory read, OpenOCD first issues an
LDC instruction into DBGITR in Stall mode (thus executing the
instruction), then switches to Fast mode and reads from DBGDTRTX once
for each word to transfer.
At the very end of the transfer, the final Fast mode read of DBGDTRTX
has, as always, the side effect of re-issuing the LDC instruction. This
causes two problems:
(1) If the word immediately beyond the end of the requested region is
inaccessible, this spurious LDC will cause a fault. On a fast CPU, the
LDC will finish executing by the time the poll of DSCR takes place,
failing the entire memory read. On a slow CPU, the LDC might finish
executing later, leaving an unexpected and confusing sticky fault lying
around for the next operation to see.
(2) If the LDC succeeds, it will leave the loaded word in DBGDTRTX, thus
setting DBGDSCR.TXFULL=1. The cortex_a_read_apb_ab_memory routine
completes without consuming that last word, thus confusing the next
routine that tries to use DBGDTRTX (this may not have any visible effect
on some implementations, because writing to DBGDTRTXint when TXFULL=1 is
defined as Unpredictable, but I believe it caused a visible problem for
me).
With this patch, the bulk mem_ap_sel_read_buf_noincr is modified to omit
the last word of the block. The second-to-last read of DBGDTRTX by that
function will cause the issue of the LDC for the last word. After
switching back to Normal mode and waiting for that instruction to
finish, do a final read of DBGDTRTX to extract the last word into the
buffer, leaving TXFULL=0.
Without this patch, memory accesses are always expanded such that they
are aligned to the access size. With this patch, accesses are issued
exactly as ordered by the caller. The caller is expected to handle
fragments at the beginning and end of the transfer if the address is
unaligned and an unaligned access is not desired.
Without this patch, the DFAR and DFSR registers, which report the
location and status of data faults, are ignored while performing memory
accesses, which could cause problems debugging an OS page fault handler.
With this patch, DFAR and DFSR are preserved across memory accesses, and
DFSR is decoded in the event of a synchronous fault to provide the
caller with more information about the reason for failure.
Thanks to Boris Brezillon for the original patch whose ideas led to the
non-word access mechanism implemented here and to various code reviewers
for their comments.
Change-Id: I11ae7104fbe69a522efadefc705c9a217a7eef41
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/2381
Tested-by: jenkins
Reviewed-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
RM0038 Rev.12 lists these new parts and introduces the category naming
scheme.
RM0367 Rev.2 (STM32L0x3 RM) doesn't add any new codes.
Change-Id: Id95dd48dda64d5f108dac57d265d29a7db3a1bd1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2495
Tested-by: jenkins
OpenOCD's SWD subsystem doesn't currently have a consistent WAIT
handling (i.e. it doesn't ever retry, just returns an error), so right
after a row write a small delay is needed as AHB access is stalled
during the flashing operation.
The issue was exposed with a samd20 using ftdi SWD transport.
Change-Id: I07d99d3a96845cc689c3904a41f4d41344f200aa
Signed-off-by: Andrej Kazmin <funnyfish@funnyfish.botik.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2268
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This optional argument tells OpenOCD to exit after finishing (either
succesfully, or with an error) the programming sequence. Without it
OpenOCD stays running.
Change-Id: I6ecaf33ff985eea9a9cd02ff644a74403ae3e1e5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2492
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently
openocd -c "echo a1; shutdown; echo a2"
outputs both "a1" and "a2" and only then shuts down. This patch fixes
it by making shutdown command throw an exception, so unless it's
caught the shutdown will behave as expected.
Change-Id: I764268b3a9046ff3e9717d04095ea0673f1d755a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2511
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Convert the DWT register store to use a byte array and fix the byte order
bug uncovered by that. Also fix an incorrect access of the PC value.
Change-Id: Idb5acab71bdf5a96895c358324b05c335e4d32ca
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2476
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The registers are represented as bit arrays intended to be accessed using
the buf_set_* and buf_get_* functions. Storing the register values in
integers enables accessing them directly, which gives different results
depending on host byte order.
Convert the register store to use a byte array instead and fix all the
byte order bugs uncovered by that.
Also merge the 32 and 64 bit register fields. Only one of them is used at
a time and after the change to byte arrays their types are also the same.
Change-Id: I456869a1737f4b4f5e8ecbfc1c63c49a75d21619
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2475
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Configure the LED to be off by default, blink on activity.
Change-Id: I8515ee66c49bddf866268b85811be15c2dbc086c
Signed-off-by: Anton Kuzmin <anton.kuzmin@cs.fau.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2539
Tested-by: jenkins
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
On armv7 there no longer are 1kB pages. Instead the bit that in
older architectures distinguished 1kB pages from 4kB pages is on
armv7 used for as execute-never marker. There may now also be 16MB
supersections with 40 bit physical address.
Change-Id: I959bdb8012782a9d07d968907a21f50e3d9b356a
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/2386
Tested-by: jenkins
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add Cortex-A5 identification to ROM-table display, and also
to cortex_a_init_debug_access. This change is mostly cosmetic.
Change-Id: I7b1dd8755d70d45eb5f315aa1918d44a813b3cdf
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/2483
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The image struct is malloc'd and hence base_address_set doesn't have a
defined value.
Caught by Valgrind.
Change-Id: Ice15b2299fc768e44e8034eeb93e035076eacd03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2524
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the board to the list of supported devices for the easy
recovery procedure. Only ram_boot is supported for this target.
Change-Id: I144e1836f8b6257e96a42c98c2668da74ce243f6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2520
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Add configs for Atheros ar9331 MIPS based WiSoC and
board based on this chip: TP-LINK TL-MR3020
Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2519
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
After profiling gmon.out was being written in little endian format only
which would cause gprof to issue and error and exit on big endian targets.
Change-Id: I526a40adae0f9a439fc5b77cef30fda228198b48
Signed-off-by: Jose de Sousa <jose.t.de.sousa@gmail.com>
Reviewed-on: http://openocd.zylin.com/2168
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.
These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.
The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.
Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds support for Silicon Labs (formerly Ember) EM357
and EM358 chips and derivatives.
Change-Id: Ie63aed95a2f4ef1a6b955e301a51b4de1b3a5462
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2470
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I53568674951ec8a5db5e191c7b50c60b5a84d0b6
Signed-off-by: Michael Brown <fractalmbrown@gmail.com>
Reviewed-on: http://openocd.zylin.com/2463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit 832f0a5bfb 'stm32: add mass erase support for STM32L' added
use of mass-erase in-place of bank-erase. This is triggered if first
bank is requested to be fully erased.
This erroneous action completely fails on STM32L162VEY (has 512 KiB
flash in two 256 KiB banks) and also unintently destroying contents of
EEPROM and second flash bank.
Change-Id: I0f13f7b0346747a09c755d72b5b95775ceff5a6f
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Reviewed-on: http://openocd.zylin.com/2441
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Topaz reports on http://sourceforge.net/p/openocd/tickets/87/ that
protection level constants are mixed up. This leads to device ending
up in protection level 1 after mass erase.
Additional work is required to actually put the device in RDP Level 1
and then back to Level 0, as Option bootloader launch is a special
kind of full target reset.
To be able to flash properly after mass_erase a "reset init" is needed
(it's anyway recommended to always perform it before any flash
operation).
Change-Id: I9a838909458039bb0114d3019723bf134fa4d7c9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2490
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This macro makes windows builds faster and helps with the old "#define
interface struct" issue as the word "interface" is part of libusb-0.1
API. However, defining it in replacements.h is too late, as windows.h
gets included by that time from somewhere else.
This solution is provided by Ray Donnelly from the MSYS2 team.
Change-Id: I376a5fb3d106786515d7e1ba44dbd751e4dcdb1b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2486
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since libusb-0.1 might be provided by libusb-compat, it will depend on
libusb-1.0, so needs to be mentioned before it in the link command
line, this is relevant for static linking.
Thanks go to mingwandroid for spotting it during MSYS2 build.
Change-Id: I15cf0b8f084c351b4f93e75686bd0f843477352b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2485
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the new STM32F446 mcu with 512 Ko
Tested with a eval board
Change-Id: I0c16ce7d32d249c7634d697815207c20e7f778c4
Signed-off-by: prudhomme.remi@gmail.com
Reviewed-on: http://openocd.zylin.com/2484
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The message as it was didn't let the user know that something was wrong
with the target or wiring.
Change-Id: Ib609c2d31959e77413e61c348d0e31d7269d5c58
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Jens Bauer <jens@gpio.dk>
This adds a trivial config for LPC8xx chips based on the already
existing infrastructure in lpc1xxx.cfg.
Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2464
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Jean-Christian de Rivaz
Matej Kupljen
Uwe Bonnes
Christopher Head
Paul Fertser
Andrej Kazmin
Andreas Fritiofson
Antony Pavlov
Anton Kuzmin
Andreas Bomholtz
Angus Gratton
Daniel Glöckner
Joerg Fischer
Olivier Schonken
Oleksij Rempel
Jose de Sousa
Pawel Si
Jacob Palsson
Ed Beroset
Nemui Trinomius
Heinz Schweiger
Michael Brown
Tomas Vanek
Jussi Kivilinna
Rémi PRUD’HOMME