Active watchdog forces reset during armv7m_checksum_memory()
in verify_image command if run just after reset init.
COP watchdog in KL series and WDOG32 in KE1 series
have longer timeout however they need to be disabled too.
The change extends 'kinetis disable_wdog' command to optionally
probe the chip and use appropriate algorithm to disable watchdog.
Setting of cache type is also split from flash_support flags.
Tcl command 'kinetis disable_wdog' is called in reset-init event.
Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3901
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3925
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis driver checks MDM STAT register to detect secured state of MCU.
Original version often reported a blank device as secured one.
Change #3010 has not fixed all false reports.
After changes in arm_adi_v5 infrastructure secured devices was not detected
at all.
New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and
MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop
are detected reliably.
Detection is run in both kx.cfg and klx.cfg from examine-start event,
not examine-end as before. Event is configured only for non hla adapter.
Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init.
Such frequency is not supported in VLPR CPU mode and with JTAG.
Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3547
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The flash definition belongs in the target cfg. Add some working area
and suitable reset_config.
Make kx.cfg more similar to klx.cfg.
Disable rclk as it is dead slow and a fixed 1MHz clock seems to work.
Change-Id: I8328f179c3a33be64403da93616abb48651bdfe6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2227
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek
Andreas Fritiofson
Paul Fertser