Commit dfc6658cf9 ("Kinetis: flash
driver described in openocd.texi") inserted a kinetis section between
fm3 and lpc2000. Then commit 43ff5acd45
("flash: New Spansion FM4 flash driver") was merged, inserting the fm4
section between kinetis and lpc2000, instead of after fm3. Finally
kinetis_ke was added between kinetis and fm4 in commit
5396ec5dcc ("flash: Added support for
Freescale Kinetis KE family.").
Restore the alphabetical order by moving the fm4 section to before
kinetis.
Change-Id: I77e47c3cd5b2cd8570b62ff2f7be8526aaf57ad0
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3484
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Initial release of Ambiq Micro Apollo flash driver
supporting our sub-threshold (low power) Cortex M4F part,
and Evaluation Kit.
We have been shipping openocd to our customers for about one year.
The EVK boards are SWD only using ftdi. We also use two of the
other COM instances to display debug information.
It takes about 15 seconds to flash 512K, and mass erase is
about 5 seconds.
Tested by internal verification group, FAE's, and customer sites.
Merged commit 'refs/changes/17/3417/1' as suggested. Makefile.am
and drivers.c follow the new format to avoid conflicts.
Removed unused fault_capture command.
Added documentation for flash driver.
Change-Id: Iae92d869369c6827244f0071f9cb522d8d91fed8
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Reviewed-on: http://openocd.zylin.com/3230
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The capability to lock the debug interface on EFM32
controllers was lacking in OpenOCD.
After receiving some pointers by zapb_ and PaulFertser
on IRC (thanks guys!) I have added this capability.
This works by writing the required bits in the debug
lock word to '0'.
Note: there is currently no way to re-enable the debug
interface from OpenOCD as doing this requires specific
pin wiggling that is currently not implemented yet.
However: having the capability to lock the debug interface
is useful when building a volume programming jig.
You can flash the program code, verify and then
lock the debug interface so that the device cannot
be read when it is deployed in the field.
Change-Id: If2d562dfdb4b95519785a4395f755d9ae3d0cf12
Signed-off-by: Lieven Hollevoet <hollie@lika.be>
Reviewed-on: http://openocd.zylin.com/3389
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The function libusb_get_port_numbers(), required for the command
ftdi_location, is only available in recent version of libusb1.
Compilation will break if the function is not available. This patch
enables the command only if libusb1 contains the necessary function.
Change-Id: I091e72dafa4ed22eea51692751d43246a8152987
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3396
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds a 'ftdi_location' command to select an adapter by usb
bus number and port path.
This is helpful if you have a rack full of adapters in a testing or
manufacturing setup where the only constant is the physical usb bus
location of the adapter you want to address. Vid:Pid are not unique,
serial number _may_ be unique (and maybe not with embedded adapters) but
will change when a new target is plugged.
Specifying a location allows to understand instantly which board failed
bringup or testing.
Change-Id: I403c7c6c8e34fe42041b3f967db80f3160a4f1a3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3351
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add support for S6E2DH MainFlash. VFlash is not implemented.
Briefly tested with SK-FM4-176L-S6E2DH V110 board.
Change-Id: If7c523d8c75307bc1494bbf4cca3eed0272e8e01
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3158
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These appear to be just additional flash size configurations.
Entirely based on manual, untested.
Change-Id: I4460dc1a588335df8fc0a385d24513a4e35b6951
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3157
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Spansion FM4 family of microcontrollers does not offer a way to
identify the chip model nor the flash size, except for Dual Flash vs.
regular layout. Therefore the family is passed as argument and
wildcard-matched - MB9BFx6x and S6E2CC families are supported.
Iterations showed that ...
1) Just doing the flash command sequence from SRAM loader code for each
half-word took 20 minutes for an 8 KB block.
2) Doing the busy-wait in the loader merely reduced the time to 19 minutes.
3) Significant performance gains were achieved by looping in loader code
rather than in OpenOCD and by maximizing the batch size across sectors,
getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB.
(Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.)
gcc, objcopy -Obinary and bin2char.sh are used for automating the
integration of hand-written assembler snippets.
Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is for targets where flash controller has reverse endianness
compared to target. For these, the 'bus_swap' parameter can be given to the
CFI driver, which will cause command CFI commands to be written with
bytes swapped. This is only for x16 CFI flash.
Change-Id: I698b768e92e65d160232e90b0e81a824e3c81a46
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3041
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to signal propagation delays, sampling TDO on rising TCK can become
quite peculiar at fast TCK rates. However, FTDI chips offer a possiblity
to sample TDO on falling edge. With this change, stable operation can be
achieved at 30MHz clock even over 10cm ribbon cable.
Change-Id: Icaf240535dae15512e3c60a944e22a5fbc1b0b06
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3180
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
work around issues with software breakpoints when the text segment
is mapped read-only by the OS. Set DACR to "all-manager" to bypass
TLB permission checks on memory access.
Change-Id: I79fd9b32b04a4d538d489896470ee30b26b72b30
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3107
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch uses libjaylink which is a library to access J-Link
devices. As other tools which are not in the scope of OpenOCD also
need to access J-Link devices a library is used. A firmware upgrade
tool and an advanced configuration tool for J-Link devices are under
development.
Further versions of libjaylink will support additional features
OpenOCD could benefit from. This includes TCP/IP as additional
possibility to connect to J-Link devices as well as power tracing and
device internal communication. The latter is used to access
peripherals on some development boards (e.g EFM32 STK and DVK).
Integration of libjaylink is realized with a git submodule like
jimtcl. As libjaylink depends on libusb-1.0 only, no additional
dependency is introduced for OpenOCD.
All low-level JTAG and SWD implementations of the current driver are
left untouched and therefore no incompabilities are to be expected.
Improvements of this patch:
* Support for more USB Product IDs, including those with the new
scheme (0x10xx). The corresponding udev rules are also updated.
* Device selection with serial number and USB address.
* Adaptive clocking is now correctly implemented and only usable for
devices with the corresponding capability.
* The target power supply can now be switched without the need for
changing configuration and power cycling the device.
* Device configuration is more restrictive and only allowed if the
required capabilities are available.
* Device configuration now shows the changes between the current
configuration of the device and the values that will be applied.
* Device configuration is verified after it is written to the device
exactly as the vendor software does.
* Connection registration is now handled properly and checks if the
maximum number of connections on a device is reached. This is also
necessary for devices which are attached via USB to OpenOCD as
some device models also support connections on TCP/IP.
* Serial Wire Output (SWO) can now be captured. This feature is not
documented by SEGGER however it is completely supported by
libjaylink.
This patch and libjaylink were tested on Ubuntu 14.04 (i386),
Debian 7 (amd64), FreeBSD 10.0 (amd64) and Windows XP SP3 (32-bit)
with the following device and target configurations:
* JTAG: J-Link v8.0, v9.0 and v9.3 with AT91SAM7S256
* SWD: SiLabs EFM32 STK 3700 (EFM32GG990F1024)
* SWD: J-Link v8.0, v9.0 and v9.3 with EFM32GG990F1024
* SWD: XMC 2Go (XMC1100)
* SWD: XMC1100 Boot Kit (XMC1100)
* SWD: IAR Systems / Olimex Eval Board (LPC1343F)
* SWD: Nordic Semiconductor nRF51 Dongle (nRF51422)
* SWD: SiLabs EZR32 WSTK 6220A (EZR32WG330FG60G)
Except for Windows XP all builds are tested with Clang in addition to
GCC. This patch and libjaylink are not tested on OSX yet.
Change-Id: I8476c57d37c6091c4b892b183da682c548ca1786
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2598
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This adds docs, example config, flash driver.
Driver is only supports K1921VK01T model for now.
Change-Id: I135259bb055dd2df1a17de99f066e2b24eae1b0f
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Reviewed-on: http://openocd.zylin.com/3011
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This makes it easier to relocate the install tree of OpenOCD from where
it was originally built (for example, if put onto a different machine),
without having to change scripts or add something to the command line
every time.
Change-Id: Ia5edf0eba166f7a999f267bd6a92402dab9b399e
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3004
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
fm3, nrf51, mdr, sim3x were at the end of the section rather than
inserted alphabetically. Fix this before adding further drivers.
Change-Id: Id23e04749cdd3b25d7503ec00fac554742d48c77
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3019
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only read access to flash chips so is through the target's
memory. Flashes like jtagspi do not expose a memory mapped interface
to the flash. These commands use the flash_driver_read() driver API
directly.
Change-Id: I40b910de650114a3f676507f9f059a234377d862
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2842
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds an option to disable the use of the JSTART instruction
when loading bitstreams to xilinx fpgas. JSTART apparently prevents
configuration if the startup clock is not set to the jtag clock in
the bitstream.
xc3sprog is omitting JSTART for all devices. Problems with loading a bitstream
that does not have StartupClk:JTAGClk are described here:
http://www.xilinx.com/support/answers/56151.html
Change-Id: I8137c0bae05a8c3c6f8e2611869f70a770d1651d
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is needed to unbreak build on systems that ship texinfo version
4.x.
Change-Id: Ie665d29b02bb65da7e8ed0d48d17fa56e231bd0d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2781
Tested-by: jenkins
Reviewed-by: David Ung <davidu@nvidia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Oleksij Rempel
This has been the case since c6216201 in 2013
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Change-Id: I70232a46e29951f05f02dec00e0695d761697aa5
Reviewed-on: http://openocd.zylin.com/2764
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Put all the individual driver descriptions to where they really
belong, fix sectioning etc.
Change-Id: I94dc09e9a296ec57db4475f8dfb0a7d62a754aa4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2770
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Directory listings are volatile and serve no purpose in the
manual. Just remove them.
Change-Id: I63d54ba209c29eafb6608cf406b8ce5d8e9ee6c8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2768
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds the mandatory Info documentation for the driver as well as
the usage field.
As a clean up, this also includes freeing of the allocated memory
which results in a memory leak if probe is invoked multiple times.
Valgrind-tested.
Reported by Dmitry Shpak.
Change-Id: I2b1d9b9e8b069c6665b11d880b40ce19a1b26ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2694
Tested-by: jenkins
Reviewed-by: Дмитрий Шпак <disona@yandex.ru>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* also included example for flash usage information
Change-Id: Icf9defc25d38bf24567b1708138b83a8de1e0497
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Reviewed-on: http://openocd.zylin.com/2705
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Run-time tested with FreeRTOS V8.1.2 (current version).
For the time being I propose this way of dealing with RTOSes that do
not export necessary information on their own.
I also suggest implementing a similar scheme for ChibiOS, exporting
the necessary struct fields' offsets via an OpenOCD-specific helper.
Change-Id: Iacf8b88004d62206215fe80011fd7592438446a3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2347
Tested-by: jenkins
This is a remake of http://openocd.zylin.com/1966
originally written by Angus Gratton <gus@projectgus.com>
ATSAM4L has a "System Manager Access Port" (SMAP) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Without this change any use of sysresetreq or srst locks the chip
in reset state until power is cycled.
A new function smap_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and SMAP reset is released then.
Change-Id: Iad736357b0f551725befa2b9e00f3bc54504f3d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2604
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch might influence openocd Tcl commands behaviour in subtle
ways, please give it a nice testing.
The idea is that if an OpenOCD Tcl command returns an error, an
exception is raised, and then the return code is propogated all the
way up (or to the "catch" if present). This allows to detect
"shutdown" which is not actually an error but has to raise an
exception to stop execution of the commands that follow it in the
script.
openocd_thread special-cases shutdown because it should then terminate
OpenOCD with a success error code, unless shutdown was called with an
optional "error" argument which means terminate with a non-zero exit
code.
Change-Id: I7b6fa8a2e24c947dc45d8def0008b4b007c478b3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2600
Tested-by: jenkins
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This should allow most of the existing configurations for older
versions to remain compatible without forcing the user to change his
or her config to explicitly select transport.
Also in some circumstances can remove the need to chain a "-c transport
select X" when building custom configs on the command line, which seems
like a common new user pitfall.
Change-Id: Ic87a38c0b9b88e88fb6d106385efce2f39381d3d
Suggested-by: Petteri Aimonen <jpa@git.mail.kapsi.fi>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2551
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
Given that the manual states that these two subcommands are
deprecated and were scheduled to be removed back in 2010,
remove them and the corresponding documentation from the
manual.
Change-Id: Iaac633349d7fcb8b7f964109c7d26dd0cc5fc233
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1860
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This optional argument tells OpenOCD to exit after finishing (either
succesfully, or with an error) the programming sequence. Without it
OpenOCD stays running.
Change-Id: I6ecaf33ff985eea9a9cd02ff644a74403ae3e1e5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2492
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The code that takes only sections marked PT_LOAD is in
image_elf_read_headers in src/target/image.c
(Just trying to save some time for the next person with same question.)
Change-Id: I493c102c908fca2b7238276ddbbecbe8c7cd9a0a
Signed-off-by: Alexei Colin <ac@alexeicolin.com>
Reviewed-on: http://openocd.zylin.com/2348
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
TI's ICDI adapter supports some additional commands which a user might
want to run for debugging or other purposes, the most useful of them
being "debug unlock" that fully mass-erases the device and unprotects
the flash.
Change-Id: I26990e736094367f92106fa891e9bb8fb0382efb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2263
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
There were two problems with the _protect() feature:
1. The address written was off by a factor of two because the address
register takes 16-bit rather than 8-bit addresses. As a result the
wrong sectors were (un)protected with the protect command. This has
been fixed.
2. The protection settings issued via the lock or unlock region commands
don't persist after reset. Making them persist requires modifying the
LOCK bits in the User Row using the infrastructure described below.
The Atmel SAMD2x MCUs provide a User Row (the size of which is one
page). This contains a few settings that users may wish to modify from
the debugger, especially during production. This change adds commands
to inspect and set:
- EEPROM size, the size in bytes of the emulated EEPROM region of the
Flash.
- Bootloader size, the size in bytes of the protected "boot" section of
the Flash.
This is done by a careful read-modify-write of the special User Row
page, avoiding erasing when possible and disallowing the changing of
documented reserved bits. The Atmel SAMD20 datasheet was used for bit
positions and descriptions, size tables, etc. and testing was done on a
SAMD20 Xplained Pro board.
It's technically possible to store arbitrary user data (ex: serial
numbers, MAC addresses, etc) in the remaining portion of the User Row
page (that is, beyond the first 64 bits of it). The infrastructure used
by the eeprom and bootloader commands can be used to access this as
well, and this seems safer than exposing the User Row as a normal Flash
sector that openocd understands due to the delicate nature of some of
the data stored there.
Change-Id: I29ca1bdbdc7884bc0ba0ad18af1b6bab78c7ad38
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2326
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reference code for the SAMD2x disables caching in the NVM controller when
issuing NVM commands. Let's do this as well to be consistent and safer.
Add a "chip-erase" for the Atmel SAMD targets that issues a complete Chip Erase
via the Device Service Unit (DSU). This can be used to "unlock" or otherwise
unbrick a chip that can't be halted or inspected, allowing the user to reflash
with new firmware.
Add a "set-security" command which issues an SSB. Once that's done and the
device is power-cycled, the flash cannot be written to until a "chip-erase" is
issued. The chip-erase cannot be issued by openocd at this time because
the device will not respond to a request for the DAP IDCODE.
Change-Id: I80122f0bbf7e3aedffe052c1e77d69dc2dba25ed
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2239
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since 6733253219 jlink adapter driver
supports SWD in addition to JTAG.
Change-Id: I9376aa02d9281f3e2734d8f127cd42162633d95b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2324
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds -alias|-nalias options to ftdi_layout_signal command that
allow to declare a new signal based on an already defined one.
Change-Id: I552578ebcd12ae21957a1c0d3b7e878adeff6df0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2181
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Adds support for auto-probing on devices which support the IAP
Read Part ID command. Includes IDs for all LPC17XX, LPC13XX,
LPC11XX and LPC11XXX devices with publicly available user
manuals.
To use auto-probing, select the 'auto' lpc2000 variant.
Change-Id: Ic617c32925c9ebe0e9d9192ed8ddbfa08e9f0aaa
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2075
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
LPC11(x)xx and LPC13xx devices are mostly compatible with the lpc1700
variant of the LPC2000 driver, but use a fixed flash sector size of 4KB.
Change-Id: I033515f4ff6bc61d3b9babd27096f78c99cea927
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2071
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should provide enough information to start using OpenOCD RPC.
I've seen some other example clients in different languages but I
can't find them anymore, and their legal status was unclear.
Change-Id: I3a95fe361d773040d1e52a62f9cc0cc655019a9f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1915
Tested-by: jenkins
Reviewed-by: Andreas Ortmann <ortmann@finf.uni-hannover.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Also add missing entries for JTAG-lock-pick Tiny 2, Xverve Signalyzer
LITE and default FTDI VID:PIDs.
Change-Id: I41b4f15409642298d1cf134d1f8014dc8f003005
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1969
Tested-by: jenkins
Intel Quark X10xx SoC debug support added
Lakemont version 1 (LMT1) is the x86 core in Quark X10xx SoC
Generic x86 32-bit code is in x86_32_common.c/h
Change-Id: If2bf77275cd0277a82558cd9895b4c66155cf368
Signed-off-by: adrian.burns@intel.com
Reviewed-on: http://openocd.zylin.com/1829
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The argument 'force' enables a user to bypass the internal cache and read
a target register directly. However it is missing from the user guide.
Change-Id: I26f689eec20b38a0dc5294626b25df566b554446
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1897
Tested-by: jenkins
By default the driver will now auto detect attached adapters, it does not
use an internal list any more. Update docs to match this.
Change-Id: I62a9d243cd236a8cf54cbd9d088c4837a8df31bf
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1902
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Changes solely to the Tcl Scripting API chapter of the UG:
* Some grammatical cleanup
* Fix formatting issues (@example and @verbatim formatting)
* Add references to missing OSes OpenBSD, NetBSD and eCos.
Change-Id: I3ec1a192a0b1e0a207dceb76fd39008d01e287a5
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1872
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
More cleanup from some of the later chapters from the User's Guide,
no functional changes.
Change-Id: Ib2860fc2574503e8107935d79db45fa96014fe3a
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1863
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove a tip describing the discouraged use of TAP numbers, and how
these numbers would be removed by mid-2010.
Change-Id: Iebe7e2e4a0f8e1f18a91d7935588dd9ced2b398d
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1862
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Various cleanups to Chapter 10 of the User's Guide, no functional
changes.
Change-Id: I055d032eacc8e85b1d8edbd4bcc505f6f0feaa49
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1861
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change-Id: Ib262d9e6330c35d26868942b821de7b53e00b854
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1859
Tested-by: jenkins
Reviewed-by: Bill Traynor <btraynor@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
This adds a set of helper functions with the aim to make it possible
to flash mass-market devices without RTFMing altogether (i.e. to
obsolete GPL-violating proprietary tjtag and other similar software).
Real-life tested on an RT-N16 and WRT54GL.
Change-Id: I197a9b28a5f386803f081057c4b4ebf2f9c447b1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1850
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
grammar fixes and so on.
Change-Id: Iaeb603447ecd9f77f1d49ce77044431442f4f219
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1855
Reviewed-by: Bill Traynor <btraynor@gmail.com>
Tested-by: jenkins
Reviewed-by: Francois Lorrain <francois.lorrain@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Re-order the "trace" parameters to allow the raw capture (log) file to
be an optional feature. The clock frequency for calculating the "Async
Clock Prescalar" is always required when enabling trace processing and
is now the first "required" parameter.
The ST-Link driver is updated to use the (required parameter)
"trace_source_hz" non-zero value as the indicator of trace being
required, rather than the now optional output file descriptor being
non-NULL.
Background: This patch is groundwork for extending the OpenOCD SWO
capture to implement other (OpenOCD built-in) ITM/DWT processing where
the core trace support is required, but there is no requirement to
store raw trace data to a configured host file. By itself this patch
is almost a functional NOP, since without the other processing in
place there is no reason NOT to specify a capture file.
Change-Id: Ibc385dd0a7adaf9bd652bceded27262fef35fd59
Signed-off-by: James G. Smith <jsmith@ecoscentric.com>
Reviewed-on: http://openocd.zylin.com/1660
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a tcl implementation of public domain tests by Michael Barr,
http://www.barrgroup.com/Embedded-Systems/How-To/Memory-Test-Suite-C
The initial porting is done by Shane Volpe and posted to the mailing
list:
http://www.mail-archive.com/openocd-development@lists.berlios.de/msg16676.html
This patch includes some cosmetic amendments plus hardcodes 32bit word
size (as the code depends on memread32/memwrite32 anyway) which fixes
original code's issue of testing only the first quarter of the
specified nBytes.
Change-Id: I5f3a66f1f16fc4082c7a5a6aba338430646ed21c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1455
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This adds support for setting the default value used when padding image
sections. Previously 0xff was used but some targets have an erased value
of 0x00.
Change-Id: If3df6fea3abf95b09daa3ff7be362acf991070ce
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1635
Tested-by: jenkins
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
@xref should be terminated by either a ',' or '.'.
Change-Id: I141335cd4e149992fc971c6f2c04f1dbe390c8f4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1637
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This patch adds a driver for the jtag_vpi server [1]. This server is
now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC).
The jtag_vpi server provides an interface between OpenOCD and a simulated
core.
[1] http://github.com/fjullien/jtag_vpi
Change-Id: I717b72cace4845f66c878581345074f99002e21a
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently we have very little info about the RTOS support. This should
improve that.
We also add info about what symbols are required for each supported RTOS.
This can be a trap, certainly when trying to use FreeRTOS support.
Change-Id: Ie57858571daca97515292ff5738a5a5ef55655b7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1538
Tested-by: jenkins
Added new configuration file for gw16042 device.
Also added this to interface/ftdi examples in documentation.
Change-Id: I07bb10bfc79a5d13007288cd57f254d889075214
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Reviewed-on: http://openocd.zylin.com/1563
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fixed a typo in device name as well updated device URL. Also fixed
miscategorization and moved it to USB FT2232 Based section.
Change-Id: Ia3acaed4209eff26244efea8db68046143ecea37
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Reviewed-on: http://openocd.zylin.com/1553
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Enable reading the SWO trace output via STLinkv2 dongles that support
it.
This adds an optional initialization parameter "trace" with which the user
specifies a destination file where SWO trace output is appended as it comes in
as well as the trace module's source clock rate.
STLink will be configured for a 2MHz SWO data rate (STLink's highest
supported rate) if the source clock is > 2MHz, otherwise the source
clock is used as the data rate directly.
For example:
trace swo.log 168000000
If "trace" is specified with a usable file path, the stlink_usb driver will
attempt to configure and read SWO trace data as follows:
- on _run(), the target's TPI and TMI are configured and the STLinkv2 is told
to enable tracing. Only generic ARM TPI and TMI registers are
configured, any MCU-specific settings (ex: pin routing) are the
responsibility of the target firmware. The configuration applied is
based on the STLinkv2's capabilities (UART emulation).
- on _v2_get_status(), the trace data (if any) is fetched from the
STLink after the target status is checked and the target is found to
be running.
- on _halt(), the STLink is told to disable tracing.
When fetching trace data, the entire trace frame is written to the output file
and that data is flushed. An external tool may be used to parse the
trace data into a more human-readable format.
Tested on ARM Cortex M4F and M3 MCUs (STM32F407 and STM32L152).
Change-Id: Ic3983d46c82ba77010c23b0e18ce7b275d917f12
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1524
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There're strong arguments against using this macro (mostly regarding
build consistency), so remove it altogether.
Change-Id: I90c8e9a86a24571019366435bd868a6799a09c45
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1476
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The currently used image is 404 so use an inline image instead.
Change-Id: I56a0d187fd06dc2c5c370e6532d89815ccec63d6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1451
Tested-by: jenkins
This adds support for JTAG programming by bitbanging GPIOs exposed on
the RaspberryPi's expansion header.
Tested by connecting directly to an STM32VLDiscovery board, without any
additional circuity. I observed maximum about 4MHz on the TCK pin with an
old analogue 'scope and about 100kHz when setting the speed to 100kHz.
Busyloop waiting is needed because even with a single 0ns nanosleep call
(with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low
to be useful.
The speed testing with adapter_khz 2000 gave the following results:
sudo chrt -f 1 nice -n -19 ./src/openocd \
-f interface/raspberrypi-native.cfg \
-c "set WORKAREASIZE 0x2000" \
-f target/stm32f1x.cfg -c "adapter_khz 2000"
wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s)
dumped 131072 bytes in 1.445699s (88.538 KiB/s)
This is 3.7 times faster for writing and 14.3 times faster for reading
compared to the generic sysfsgpio driver; probably the writing speed is
limited by the target itself here and reading speed might be considerably
higher too with appropriate connection and a capable target.
BCM2835 name is choosen over BCM2708 because the published peripherals
datasheet uses the particular model name and not family name.
Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/758
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As per request from Peter at Ultimate Solutions, updated the
description of the ZY100 Stand-alone JTAG probe.
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Change-Id: Ia5c0b9a7261becd524a02aba1b22a98a2e09a4c9
Signed-off-by: William M.A. Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/1357
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add command to fix CSW_SPROT in register AP_CSW.
This solves dap apmem access in non secure access.
Change-Id: I7cfcb6434d75f5cfd4a2630a059901cdeea010ce
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-on: http://openocd.zylin.com/1276
Tested-by: jenkins
Reviewed-by: mike brown
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These were missed when git was moved to the new SF platform during Nov 2012.
Change-Id: I7b4ae9dea010d95f9bf4c26841b5b724f41768be
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1248
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
makeinfo has a long outstanding bug that means @anchors are not correctly
formatted for split html, see:
http://lists.gnu.org/archive/html/bug-texinfo/2012-06/msg00000.html
The issue relates to using spaces or hyphens in the @anchor name.
Issue also reported via Trac #44
Change-Id: Id72e23375dd167674b2ae5b314e8242b90a72a5f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1244
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It was listed in the ft2232 based cables supported. Moreover, the
ft2232_channel option, which was added to support this cable, was explained.
Change-Id: I82ebc7bc10d6472f96ab150e78d623a617edccd2
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a program proc that simplifies using OpenOCD as a standalone
programmer.
Change-Id: I6ece492cd878c170b734e8bb2e09fe8c4557d5a6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1199
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
It has been seen on some stm32 targets that the flash size register that
is probed by the driver may contain an invalid size.
This change enables the user to override the probed value.
Change-Id: I09359e59a96f9133d3d939670957d32a830a944e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1132
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
As we use the two ST flash drivers for multiple stm32 variants update the
docs as to which targets use which driver.
Change-Id: I84943ff45482a22b3d3dd8491bb4242d79415939
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/990
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the ability to request to the adapter how we want to connect to
the target, eg. while srst is asserted or not.
This ability can very handy for connecting to unresponsive targets.
A prerequisite is that the target supports srst_nogate.
Change-Id: I0f7c9475160048e8a963e16077754f5403ac8325
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/976
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch adds ChibiOS/RT support. This patch requires at least
ChibiOS/RT development version starting from SVN revision 4734.
Note, that the Thread structures depend not only on the target
but also on the ChibiOS configuration at build time.
To correct this ChibiOS includes a new "memory signature" which
specifies the offsets.
Special thanks go to Peter Stuge and Spencer Oliver for their
continous input and feedback to this patch.
Change-Id: I842bf7ba6c2309a4efe93d29ea6cd0784a8b22a3
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/901
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The J-Link related commands and configuration commands were added
to the "8.2 Interface Drivers" section of the manual.
(previously they were enumerated as comments).
The 'jlink pid' was marked as Config all other as Command.
A draft of a compatibility note was added, but probably
a table would be more appropriate.
Change-Id: Ifbe230706815196aaad4e3729ed5089d5088b769
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/680
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These events have been deprecated for a number of years, update any
remaining scripts to the new events.
Change-Id: Ic31ff388545ac8b3a500045699ca92c541b13f12
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/634
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
User Guide: Chapter 6 'Config File Guidelines'. The directory listings
of interfaces, boards, and targets has been brought up to date.
Change-Id: I53f218a94cb81c5e90298b367259e833192af5f3
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/646
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit 9ca1592cb9 started on documentation
for the -rtos option, but some of the documented values were incorrect so
we'll clean up the mess here.
Many thanks to Freddie Chopin for spotting this!
Change-Id: Iaa633bd40ff5f75dd6a69e74e79dafc1643ee21a
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/642
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
This enables the manual selection of the stlink api version.
Change-Id: I0ec8c5b0a101b6456f426d2fec65971da56db4e7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/617
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.8 USB Other' updated the link to the USBprog tool:
http://shop.embedded-projects.net/
Change-Id: I7fa453934ac6a7889e01b22b7e0cb07f42ee168d
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/591
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.8 USB Other' updated the URL to the Versaloon-Link to:
http://www.versaloon.com
Change-Id: Idd92333cb3d87d1b89dfb282134332387df5a0fc
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/592
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.9 IBM PC Parallel Printer Port based' fixed link to
the Wiggler2 project and removed the alternate URL text to retain
style consistency with the other URLs in the document:
http://www.ccac.rwth-aachen.de/~michaels/index.php/hardware/armjtag
Change-Id: I879db1c6eaf683ca6475a0f466f987087c9d60d0
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/593
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.9 IBM PC Parallel Printer Port Based' fixed link to
ST's flashlink PDF and removed alternate URL text:
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/
DATA_BRIEF/DM00039500.pdf
Change-Id: I99702dd00d4145784baee1f63b5998bf79e06678
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/594
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In Section 2.7 USB ST-LINK based made these two changes:
"they only works with" to "they only work with"
"following method's" to "following methods"
Change-Id: Idfe6c11c3fa6f2157d01697cd7f480a9d495c8e2
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/590
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updated the link for the usbjtag project to the correct URL:
http://elk.informatik.fh-augsburg.de/hhweb/doc/openocd/usbjtag/usbjtag.html
Added a NOTE to indicate the axm0432_jtag as no longer being
available from the axman.com page.
Change-Id: I70727303dad58d9dc0c5f9b7cce219288b762042
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/583
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added the Flyswatter2 to section 2.3 USB FT2232 Based hardware
list.
Change-Id: I6a382644b5a0313d30afb5a97d0a9ea00f01efa9
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/584
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch fixes the link to the Zylin ZY1000 JTAG Probe webpage.
The ZY1000 product line was acquired by Ultimate Solutions, Inc. in May 2011.
Change-Id: If68cd45a0c47aa20b2e4bb62939b2c505c8c8c2e
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/571
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Added support to the FT2232 driver for the FT2232H-based
Digilent HS1 adapter.
Change-Id: Iab6cc15f299badaf115615b5d4d785ecb2273c27
Signed-off-by: Stephane Bonnet <bonnetst@hds.utc.fr>
Reviewed-on: http://openocd.zylin.com/558
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
we already have a link to the patch primer in the main index.
Change-Id: Ib90ade76a17f5d99da8fe481d8f87c68eca38f1c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/546
Tested-by: jenkins
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
when -ignore-version is used we should mask of the upper 4bits not 8bits.
Change-Id: I9ffe24c2aeeb414677357a647609fdf018890194
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/473
Tested-by: jenkins
A period or comma must follow the closing brace of an @xref.
Change-Id: Ida5dc3600eca328d95b0a8f6b5c9fe0a0f3ba820
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/475
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
A period or comma must follow the closing brace of an @xref.
Change-Id: I272f1e7fac8f1fee4844f485b0b8e2e4e9cf352d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/456
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This patch adds init_board concept information to OpenOCD manual.
Additionally a link from init_targets chapter to new chapter about
init_board is added.
Change-Id: I09b9aaa1cf68b94f35701224f641cae9811a5bcf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/440
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a note to the docs about the original stlink being broken under linux.
Change-Id: Ib440d78e5c7d31eeace99f611a76fcf701bfb8bc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/433
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
The lm3s variant is not required as this is handled in the
target script - see tcl/target/stellaris.cfg.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
this will allow us to use multiple jlink at the same time as when
the USB-Address is specified the PID change from 0x0101 to
(0x101 + usb_adress)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This piggy backs on JTAG so it's not yet pretty, but that
seems unavoidable so far given today's OpenOCD internals.
SWD init and data transfer are unfinished and untested, but
that should cause no regressions, and will be addressed by
the time drivers start using this infrastructure. Checking
in whould get the code working better sooner, and turn up any
structural/architectural issues while they're easier to fix.
The debug adapter drivers will provide simple SWD driver
structs with methods that kick in as needed (instead of JTAG).
So far just one adapter driver has been updated (not yet
ready to use or circulate).
The biggest issues are probably
- fault handling, where the ARM Debug Interface V5 pipelining
needs work in both JTAG and SWD modes and
- missing rewrite of block I/O code to work on both of our
Cortex-ready transports (Current code is hard-wired to JTAG);
relates also to the pipelining issue.
- omitted support to activate/deactivate SWO/SWV trace (this is
technically trivial, but configuring what to trace is NOT.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
----
doc/openocd.texi | 17 ++
src/jtag/core.c | 3
src/jtag/interface.h | 4
src/jtag/jtag.h | 2
src/jtag/swd.h | 114 +++++++++++++++++++
src/jtag/tcl.c | 2
src/target/adi_v5_swd.c | 281 ++++++++++++++++++++++++++++++++++++++++++++++--
src/target/arm_adi_v5.c | 8 +
src/target/arm_adi_v5.h | 3
9 files changed, 425 insertions(+), 9 deletions(-)
STMicroelectronics controller SMI is not SPEAr specific.
Rename it and change name to every symbol in the code.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
this never panned out and there are enough mistakes in
the code that probably nobody used this.
Use the tcl server and implement a standalone http
app instead works fine.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Andreas Färber
Rick Foos
Lieven Hollevoet
Matthias Welwarsky
Ivan Meleca
Tomas Vanek
Esben Haabendal
Matthias Welwarsky
Marc Schink
Bogdan Kolbov
Jeff Ciesielski
Morgan Quigley
Evan Hunter
Jonathan Larmour
fenugrec
Austin Morton
Robert Jordens
Paul Fertser
Karl Palsson
Spencer Oliver
Mahavir Jain
Andreas Fritiofson
Marian Cingel
Angus Gratton
Nemui Trinomius
Robert P. J. Day
Andreas Bomholtz
Joerg Fischer
Alexei Colin
Andrey Yurovsky
Austin Phillips
Cosmin Gorgovan
Andrey Smirnov
Adrian Burns
Mathias K
Sergio Chico
James G. Smith
Franck Jullien
Pushpal Sidhu
William M.A. Traynor
Freddie Chopin
Michel JAOUEN
Rodrigo Melo
Drasko DRASKOVIC
Roman D
Matthias Blaicher
George Harris
Liviu Ionescu
Peter Stuge
Olivier Schonken
Stephane Bonnet
Øyvind Harboe
Timo Ketola
Erik Ahlén
Uwe Hermann
Spencer Oliver
Richard Uhler
Jie Zhang
Peter Horn
Phil
Jean-Christophe PLAGNIOL-VILLARD
Aaron Carroll
David Brownell
Antonio Borneo