The encoding of BKPT instruction is 0xE12###7#, where the four '#'
characters should be replaced by the 16 bits immediate value.
The macro uses an incorrect shift amount, thus the immediate value
is not properly coded and bits 20~23 of the opcode could get
corrupted.
Fixed by using the proper shift amount.
Change-Id: I32db8224ab57aad6d3b002f92f9f259056593675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4854
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Fix the SWD line reset sequence accordingly to Arm specification IHI
0031E that requires at least 2 idle clocks after the 50 clocks with
SWDIO high.
Fix the value of the activation code in the (currently unused)
sequence dormant-to-SWD.
Make each sequence's length multiple of 8, so it is compatible with
adapters that have such limitation (e.g. buspirate) and try to split
and comment each part of the sequence (when possible keep each part
byte aligned, inspired from commit 3ef9beb52c). This slightly
increases the sequence length but does not impact run-time
performance because these are rarely used sequences.
Add the missing sequence dormant-to-JTAG and JTAG-to-dormant, not
used yet.
On devices that implements the dormant state, IHI 0031E deprecates
the direct switching between SWD and JTAG, and recommends using a
transition through dormant. This is not implemented.
Change-Id: Iad18c0e736cfd9366be175d22658d664b0c61eab
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4851
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This hardware id is e.g. used by the Insight SiP ISP1507-AX.
Change-Id: I82568d292f9882372ab061d8e3e36906b0cc5882
Signed-off-by: Mirko Vogt <mirko.vogt@sensorberg.com>
Reviewed-on: http://openocd.zylin.com/4845
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This patch covers the fact that cortex_m could be resumed externally by
Cross Trigger Interface or by direct write to DHSCR ...
To reproduce:
- halt the target
- then run the core through DHCSR (mww 0xe000edf0 0xa05f0001)
=> this resumes the core, but target state in OpenOCD remains HALTED.
Change-Id: Ifa1ae18645bfeb863acc78a039bbf04873fd78fe
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4817
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cortex_a_debug_entry and update_halt_gdb are called in two consecutive
conditions which are complementary, so externalizing the common code
makes the conditions' body lighter
With the removal of LOG_DEBUG(" ") since it does not look too informative
Change-Id: I0c54e413619576bb3af164f2dcf256c5a862c5fd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4832
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
If malloc fails in __command_name, the following strcpy will
segfault, thus preventing __command_name to return.
The actual calls to command_name() implement the correct check
for the NULL pointer, but propagate error -ENOMEM, that is not
an error value coherent within OpenOCD. Plus, in one case it
overwrites an already detected error.
Check the pointer returned by malloc and, in case of failure,
issue an error message and return the NULL pointer.
Let the caller of command_name() to keep the already detected
error or to return ERROR_FAIL in case of end of memory.
Change-Id: I151a24569409777dd5bc09a3daf5dba2b8e2829b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4838
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio.
Change-Id: If5b3c618097b71dfe7fcf988fb3c1499ae03a6d5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4833
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Valgrind and Clang Static Analyzer have no complaints about this change.
Change-Id: I7757615ec52448372bdc57729cdf97c7016d97e8
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4656
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commands to stlink devices are typically comprised of multiple
transactions with each transaction completing before moving to the next.
This change allows for multiple USB transactions to be issued at once
followed by a check that all transactions completed successfully. This
improves performance on some machines where there is a large turn-around
time between USB transfers such as is seen on some virtual machines.
This change is only supported when compiled with libusb1 as libusb1
supports and asynchronous interface.
Multi-transaction queueing introduced in this change paves the way for
improving speed of other transactions in the future such as memory and
register reads where multiple USB transactions in succession are
required to complete a command. Multiple USB transactions can be
submitted at once using jtag_libusb_bulk_transfer_n function.
Change-Id: I924e049217a789ef445b14e00aa1983576970fbf
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4484
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When few adapters of the same type are in use, the serial string is
the way to select the right one.
Currently a serial string that does not match any of the connected
adapters will just fail the open, without specific information to
track the issue.
Add a specific message to highlight that the open failure is caused
by a serial mismatch.
Change-Id: I5cb77f1045cc746e532d395b2e5ced40a23ab638
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4701
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Where possible, keep the same style for returning error.
Change-Id: I3a04220c0b9f129a36e9fe83038b7c19dd57fe61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4699
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d1b7437633 fixes libusb1 to
return OpenOCD error values instead of negative errors in Linux
kernel's style.
The same fix should be applied to libusb0 too.
Fix return value of libusb0 to uniform it to OpenOCD style.
Change-Id: I68478c29c91c6be720074f58c432fe51477e03ed
Fixes: d1b7437633 ("libusb: return oocd error values")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4698
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
aarch64-linux-gnu-gdb 8.2 uses "aarch64" as default architecture,
but also supports the value "aarch64:ilp32" and all the values
supported by arm-none-eabi-gdb.
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for aarch64 target to "aarch64".
Change-Id: I63e9769f47d8e73f048eb84fa73e082dd1c8e52c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4755
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
arm-none-eabi-gdb 8.2 uses "arm" as default architecture, but also
supports the following values: "arm_any", "armv2", "armv2a",
"armv3", "armv3m", "armv4", "armv4t", "armv5", "armv5t", "armv5te",
"armv5tej", "armv6", "armv6k", "armv6kz", "armv6-m", "armv6s-m",
"armv6t2", "armv7", "armv7e-m", "armv8-a", "armv8-m.base",
"armv8-m.main", "armv8-r", "ep9312", "iwmmxt", "iwmmxt2", "xscale".
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for all arm targets to "arm".
Change-Id: I176cb89878606e1febd546ce26543b3e7849500a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4754
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
The gdb patches for stm8 are still not merged in the official
repository and are temporarily hosted in
https://stm8-binutils-gdb.sourceforge.io/
The latest patch set
stm8-binutils-gdb-sources-2018-03-04.tar.gz
define only one possible value ("stm8") for this architecture; it
can be displayed typing "set architecture " followed by a TAB for
autocompletion in gdb for stm8.
Set the gdb architecture value for stm8 to "stm8".
Change-Id: I643ceba662de46cecf061d1dc672b9178a077f1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4753
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
xPSR.T sets the processor to Thumb mode when set to 1. ARMv7-M only
supports execution of Thumb instructions, so it must always be set to 1.
If xPSR.T is set to 0 on armv7m, a usage fault is generated when a
instruction execution is attempted.
On armv7m, issuing a reset causes the vector table to be examined. PC
and xPSR.T are loaded from the vector table at byte offset 4. xPSR.T is
taken from the least significant bit this value, PC from the remaining
bits. This occurs even with `reset halt`, as the reset itself causes
this load to occur without the execution of any instructions.
As a result of this, following a reset with a "bad" value programmed in
the vector table, openocd would be unable to run algorithms on the
target, as running them would immediately result in a usage fault due to
xPSR.T being unset (0).
Allow algorithms to run regardless of the content of the vector table by
explicitly setting xPSR so that xPSR.T=1 prior to executing an
algorithm. One can think of this as openocd more closely emulating a
reset or branch instruction in executing it's algorithms.
Ticket: https://sourceforge.net/p/openocd/tickets/203/
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: I4dc3427ab195d06c3fd780ea768027fefccc4c28
Reviewed-on: http://openocd.zylin.com/4658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Agama family of devices (CC26x2/CC13x2) required an
additional bit to be set when adding the core's TAP into
the scan chain. The cancel reset bit 0x10000 tells the
ICEPick to take the bus out of reset so that the other
bits will take effect. This bit is a NOP on other devices
and ICEPicks, so the change shouldn't adversely affect
other devices.
Change-Id: I9245eef0936ea7eea28ae84ab5e8ce05fa63af40
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The XDS110 stand-alone version has the ability to supply
voltage to the target board via it's AUX FUNCTIONS port.
Added command to enable setting the voltage on the XDS110
stand-alone.
Change-Id: I2f21c4a3d15ed99e649f3a83973c5e724c4bfeb6
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4793
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The fact that one needs to always push contributions to a single
remote reference (refs/for/master) might seem odd to people unfamiliar
with Gerrit. GitHub, for instance, hosts personal repositories where
developers typically create topic branches for each contribution and
use a proprietary mecanism to request a review (the "pull request").
More generally, one normally does not expect to be able to push
non-fast-forwarding stuff to a remote branch.
This commit adds a clarifying note to the patch guidelines.
Change-Id: Ia750b815b82b18e92b6109c07f451000dcbecf9b
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-on: http://openocd.zylin.com/4806
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
refs/publish/master is deprecated and gives a warning in newer Gerrit.
Replace with refs/for/master.
Change-Id: I56871cc6e80c014ba81f4458230cd67dc318ecb3
Suggested-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-on: http://openocd.zylin.com/4810
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Longest erase all FLASH for nRF5 series is 295.3 ms for nRF52832.
Timeout period now is set to 340 ms (295.3 + 15%)
Change-Id: Iae00ed7b634f111b9798db11e35e4e066d4aaa95
Signed-off-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-on: http://openocd.zylin.com/4822
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this permits the full control of CTI from config files
Change-Id: Ia27ac8e12e08ec72da05f26dcbd81d24fa1a0f6f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4815
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
w600 is a wifi soc from winner micro(www.winnermicro.com).
Change-Id: Ib8ccd6e52baefca6547fb97d29db75db0ee73948
Signed-off-by: Simon Qian <versaloon@simonqian.com>
Reviewed-on: http://openocd.zylin.com/4801
Tested-by: jenkins
Reviewed-by: yichen <wdyichen@wdyichen.cn>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target configure -work-area-xxx calls target_free_all_working_areas()
and sets the desired new parameter. Without this change the working area
does not get reallocated if it has been allocated before.
target_free_all_working_areas() results in work area containing one block
marked as free.
Completely free working area in target_free_all_working_areas()
Change-Id: I79c681082f32f2a96a2b40eb3b8751e427549693
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4797
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The block of code moved without any changes
Change-Id: I70b82dc3315dcc3f34de0537b362bee230007d02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove option 'srst' which is not recognized from on-line help and texi.
Check parameter and return syntax error if wrong option is entered.
Change-Id: I87daa423a9f53193a0b015080594820b933628f5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4795
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Cortex-M0, M0+ and M1 do not support VECTRESET bit in AIRCR.
Without this change the 'reset' command silently fails if VECTRESET
is requested.
Detect these cores, show warning if VECTRESET is about to use
and use SYSRESETREQ instead.
Change-Id: Ief174373e3ef0e6b287c57911c0aca4dfa8209f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4794
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This commit adds TARGET_HALTED check in armv8_get_core_reg32()
and armv8_set_core_reg32() to void a crash issue when gdb connects
but fails to halt the ARM core. Similar logic can be found in
armv8_get_core_reg() and armv8_set_core_reg().
Below is the call stack information of this case when gdb connects.
(gdb) bt
regnum=regnum@entry=0, dpm=0x990110) at src/target/armv8_dpm.c:657
r=0x9c7240, regnum=0, mode=<optimized out>) at src/target/armv8_dpm.c:974
at src/target/armv8.c:1487
packet=0x8ec8e0 <gdb_packet_buffer.9962> "g",
packet_size=<optimized out>, connection=<optimized out>)
at src/server/gdb_server.c:1200
at src/server/gdb_server.c:3180
command_context=command_context@entry=0x935010)
at src/server/server.c:566
...
Change-Id: I159837b533f110998184f910a0abe48409bd58f1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/4758
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Arm architecture reference manual DDI0406C reports at page 2024 in
table C3-1 the processor behaviour on debug events depending on
the debug-mode (none, monitor or halt), mode selected through the
bits MDBGen and HDBGen in DSCR register.
The halt request is served independently from the debug-mode. Thus
it's useless to enable the halt debug-mode in cortex_a_halt() by
setting the bit HDBGen (macro DSCR_HALT_DBG_MODE).
On the other side, halting for a breakpoint, a watchpoint or a
vector catch requires being in halt debug-mode.
Today HDBGen is set only in cortex_a_halt(), so we are forced to
halt the core at least once before it can be halted for hitting a
breakpoint/watchpoint/vector-catch. This is annoying since there
is no need to halt the target to set a HW breakpoint.
Move in cortex_a_init_debug_access() the selection of the halt
debug-mode, so the mode is set during examine.
To prevent a misconfigured hardware breakpoint/watchpoint/vector
catch to halt the target when OpenOCD has already quit, return to
debug-mode none at OpenOCD exit.
Change-Id: I68a1c51de3572ca1b89e90caf7eb20374268e926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4783
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
DEBUG_WAIT is useful to debug adi_jtag issue,
and the WCR register is replaced by DLCR for DP registers update
in commit 150b7d26f2.
Change-Id: I3faa9ea8a6adacd3d5275e40382801da731db32f
Signed-off-by: YanLin Zhu <zhuyanlin@pinecone.net>
Reviewed-on: http://openocd.zylin.com/4804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
The OpenOCD commands that have been wrapped with 'ocd_bouncer' are
executed within two levels of nested proc's:
# see register_command_handler() in src/helper/command.c
proc my_command {args} {eval ocd_bouncer my_command $args}
# see ocd_bouncer in src/helper/startup.tcl
proc ocd_bouncer {name args} {
... [eval ocd_my_command $args] ...
}
This causes the stack frame of 'ocd_my_command' to be the same one
of proc 'ocd_bouncer', thus two levels below the stack frame of the
caller of 'my_command'. This is an issue with commands that receive
a variable by name and have to resolve them to access the value.
E.g. the command
<target> mem2array arrayname bitwidth address count
is wrapped; it receives the name of the array but fails to resolve
it in the current stack frame. Instead, the commands
mem2array arrayname bitwidth address count
ocd_<target> mem2array arrayname bitwidth address count
are not wrapped and can directly access the array because they share
the same stack frame of the caller.
Same situation with the symmetric commands 'array2mem'.
How to test:
within a telnet connection, run the following set of commands,
eventually replacing the address 0x08000000 with a valid readable
address of your <target>,
unset -nocomplain v1 v2 v3
info vars v?
mem2array v1 32 0x08000000 1
<target> mem2array v2 32 0x08000000 1
ocd_<target> mem2array v3 32 0x08000000 1
info vars v?
and notice that only v1 and v3 are now allocated. The array v2 has
been allocated in the temporarily stack frame of proc ocd_bouncer,
together with its local variables, and then lost when proc ended.
Fixed by executing the wrapped commands with the command 'uplevel'
instead of 'eval'. The amount of levels to skip is checked to avoid
errors in the unusual case 'ocd_bouncer' is called directly without
the first level of wrapper.
Change-Id: Iff90fb8921faf9b5ab04f61062a530578cc20d78
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4731
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Slow version of blank check procedure reads target memory sector-by-sector
using 1 KB chunks. Due to bug in chunk size calculation algorithm the actual
size of the chunk is always 1 KB even if sector size is smaller.
This causes out-of-boundary read of the last sector.
Steps to reproduce:
1) Use target with small sectors (e.g. psoc6 with 512-byte sectors)
2) set WORKAREASIZE_CM0 0
3) flash erase_check 1
Running slow fallback erase check - add working memory
Info : SWD DPIDR 0x6ba02477
Error: Failed to read memory at 0x14008000
unknown error when checking erase state of flash bank #1 at 0x14000000
Bank is erased
Change-Id: I03d0d5fb3a1950ae6aac425f5e24c7fd94b38325
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4785
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch removes use of register write protection in protect() and
protect_check() now that Change 4765 has merged.
Change-Id: I42c429dc283c5b53989a6b98ebfc58214274ff16
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4791
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds support for instruction tracing to eSi-RISC targets. The
command interface is borrowed heavily from ETM; eSi-Trace uses a less
sophisticated model for tracing, however the setup and usage is similar.
This patch also cleans up the command interfaces of the other esirisc
command groups and adds additional debugging information to log messages
when dealing with CSRs.
This patch "finalizes" support for 32-bit eSi-RISC targets.
Change-Id: Ia2a9de79a3c7c066240b5212721fb1b7584a9a45
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4780
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
original CC3200 launchpad works only with ti-icdi driver
which stopped to work after merging to master commit
d02de3a8a9
Change-Id: I247b5d99831fa744de1fdc5b8a7cffdf49fe953c
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/4792
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When GDB analyses the status of the target it try to guess the
current stack frame and issues few memory read.
E.g. on ARM targets GDB uses R11 value as a potential frame-pointer
and reads at the address pointed by R11.
The address of such memory read is not always valid and can trigger
an address translation failure.
Replace LOG_ERROR with LOG_WARNING in case the virtual address does
not have a hit in TTB; print the virtual address in the warning
message and discriminate the two identical messages with [1]/[2].
Change-Id: I288b8cd26bec2543c4f1c16b7c06dc47d5d843d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4602
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For compatibility with libusb1, define LIBUSB_TRANSFER_TYPE_BULK
in libusb0.
Remove the #ifdef HAVE_LIBUSB1 in jtag/driver/aice
This also fixes a compile error in jtag/drivers/openjtag with
libusb0.
Change-Id: I827b77eac10216759eb31aab461b2b63cabaf195
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4700
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updates support for L4+ device id: 0x470 added by #4310
Extends #4641 to account for L4+ use of multiple DBANK option bits
Enables L4+ 1M and 2M devices to be programmed using sector erase
Change-Id: I42bb379d7d97986f4506423e3da503d07c787c6b
Signed-off-by: bob <rea952@gmail.com>
Reviewed-on: http://openocd.zylin.com/4777
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove inappropriate use of bank_number.
Change-Id: I11be1f2540cb09a3ccede35312f90bc8276af338
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4788
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All SWD GPIOs should be un-exported when no longer needed, not just
srst.
Change-Id: I998377afe43b72446cab3da2d4406fc2912ff8c3
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Reviewed-on: http://openocd.zylin.com/4784
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Antonio Borneo
Tomas Vanek
Mirko Vogt
Tarek BOCHKATI
Severin Junker
Tim Newsome
Austin Phillips
Cody P Schafer
Edward Fewell
Jerome Forissier
Rod Boyce
Oleksij Rempel
Jānis Skujenieks
Tarek BOUCHKATI
Jean-Christian de Rivaz
Simon Qian
Liming Sun
YanLin Zhu
Bohdan Tymkiv
Steven Stallion
Jiri Kastner
bob
Reto Schneider