Move the global target back off timer to the target struct. This will
fix the wrong error handling with multi target devices like smp systems.
Change-Id: Ia327182ed5d13ca87323700017a8c40ecc6b25a3
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1179
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Inform about possibility of discarding negative review in Gerrit when specific conditions are met.
Change-Id: I432b6c93cefc368fa22ce1096bea4cd174e03816
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/747
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
The USB buffer will need space for both TMS and TDI buffers.
Each holds tap_buffer_size bytes maximum, so tap_buffer_size must be
smaller than half of usb buf_size.
Change-Id: Id8f39936a894cbd98deb89eec5a859aef1e2b783
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/1136
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Because we were always running using target state TARGET_RUNNING target
algorithm's were a bit verbose compared to other targets.
This brings the hla target inline with the other targets.
Change-Id: I3a257fdc878b87660fac8b5eca22b421eee5b349
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1134
Tested-by: jenkins
The was missed when the armv7m was moved over to using the std arm
core_cache, probably because it is disabled by default.
Change-Id: I2f5a18ef6dd783b36e8c29f4c52379104bda4583
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1138
Tested-by: jenkins
Added support for new ST devices in the stm32lx portfolio, with device
id 0x427. These have 256k flash, but in a single bank compared to
device id 0x436 which is a dual bank flash.
Change-Id: Iafdfe990f24bd04b0d6e00385ee70690f3bf8d5f
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1140
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update adds support for the STM32Lx 384kb dual bank flash. Previously there was a problem when writing an
image that was larger than 192Kb. That lead to openocd printing out two error messages like
"Error: access denied / write protected" and "Error: invalid program address". The reason was that the stm32lx
driver tried to write half pages which overlapped into the next flash bank.
A new configuration file stm32lx_dual_bank.cfg can be used for stm32lx chips with dual bank flash (256kb or 384kb devices).
A sanity check was added for probed flash size values to fix the issue seen on some ST samples that answered incorrectly.
Change-Id: I69e25131983d88613be8606b438f98870c5f1e52
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It has been seen on some stm32 targets that the flash size register that
is probed by the driver may contain an invalid size.
This change enables the user to override the probed value.
Change-Id: I09359e59a96f9133d3d939670957d32a830a944e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1132
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
adapter_init (core.c) won't check speed configuration
of the selected interface if it's not needed (.speed = NULL).
When it's not needed, we can now omit adapter_khz in
init scripts and we don't have to implement dummy handlers
for speed_div and khz functions.
It also removes calls to adapter_khz in interface configuration
files when not used anymore.
Change-Id: I6eb1894385503fede542a368f297cec6565eed44
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1131
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This makes sure we are using privileged mode when executing any loaders.
Change-Id: I18bf32ec92e1c76a66ab25e3712652bc3650b332
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1108
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Make sure we restore the core mode after executing any algorithm.
We also now check that we actually need to swap the core mode, we may
already be in the correct mode.
Change-Id: Ia48af2c108e0f9868aae241bf25f60323503f092
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1107
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This removes the armv7m::core_cache and uses the generic arm::core_cache.
Change-Id: If854281b31486cea8be005008f6a71a691b4c208
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/968
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This simplifies the armv7m_core_reg structure ready for the move to using
the generic struct arm_reg.
Change-Id: I8edb9d77cc54965d49cd2e754568ebcea4cf6964
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/967
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
To simplify things change over to using the generic core_mode struct rather
than maintaining a armv7m specific one.
Change-Id: Ibf32b785d896fef4f33307fabe0d8eb266f7086f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/966
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The current implementation of hexify was not correctly handling signed chars.
This function is currently used by the ti-icdi driver and as such was causing
random write issues.
As a note perhaps a better long term fix would be to change to using uint8_t
buffers rather than char. This will require changes to the ti-icdi driver
aswell.
Change-Id: I572e69ff2b99227a7d412de056458c0393794b03
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1124
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
LOG_OUTPUT is not intended for general output so use the correct LOG_*
functions instead.
Change-Id: I48d0fe765637024dbafc68f2ea08219d3ff42754
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1104
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
ThreadX support was not working due to it being first in the list of RTOS - regression.
Auto-detect off, an RTOS was always be marked as successfully detected, even if symbols are not found.
Lines 223-227 were unnecessary as they are done in rtos_try_next()
Added lots of comments
Improved readability by separating: GDB not finding a symbol vs no more symbols being available
Regression caused by patch which was allowed only 52 minutes for review : http://openocd.zylin.com/895
Change-Id: Ib4decb01db595ddb3796837c6d8338ce6b9a91ca
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/986
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
All the other drivers will only change the state if required.
This brings all the other drivers inline with this behaviour.
The original issue relates to problems on xscale commit 7989000e09
Change-Id: Ifc90ec2eef68a70a14f37c00931a07982bfa200c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1114
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
There is no constraint about idProduct in USB spec. So, pids[i] may be 0 for USB devices.
Change-Id: I19d8974f4e7082e8b7e1f2d33c019ac4e61bc1e2
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1091
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The makes sure the DWT component is always enabled so that watchpoints
work as expected.
This does need merging into the existing cortex_m logic, however at the
moment this is non trivial.
Change-Id: Ic6cccd1badb51f70a2ca8ea9ab6923788a94c1bf
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1122
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
An issue has been seen with the stm32lx flash driver that if a
power cycle/reset is applied after a erase, any ram loader will Hard Fault
on execution.
A similar issue is mentioned in the errata for the device.
Two solution's seem to workaround this issue:
1, Handle the exception, this means adding exception vectors to the loader
and changing the exception address using nvic vtor register.
2. falling back to using slower direct page writes - approx 50% slower.
Using solution 1 would mean restrictions are placed on the loader location.
Solution 2 was chosen mainly as it was simpler too implement.
Change-Id: I429f06b5a3e3b1d8de90071a88a7df11fc9b46a7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1010
Tested-by: jenkins
Waiting 20secs is a bit much excessive, we could probably reduce to 5.
Change-Id: Iffb97adb99c2541a075fe78dbc88a53ddf340214
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1009
Tested-by: jenkins
Handle any leading bytes upto the next 128 byte page, enabling us to safely
use the faster page write.
Rather than use a separate word/byte write to program any trailing bytes
we use a combined write function.
Use memcpy for byte writes and change loader to using bytes.
Change-Id: Ie0164a30388f018dd00e752cf5ff87d4f96ced97
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1008
Tested-by: jenkins
As we use the two ST flash drivers for multiple stm32 variants update the
docs as to which targets use which driver.
Change-Id: I84943ff45482a22b3d3dd8491bb4242d79415939
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/990
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
automake-1.13 has now deprecated AM_CONFIG_HEADER, use the correct
AC_CONFIG_HEADERS instead.
Change-Id: I8adaec64cbad7f7318ff69091176c30b707cbb0b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1117
Tested-by: jenkins
Reviewed-by: Mikko Viitamäki <mikko.viitamaki@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Fixed flash page size detection according to EFM32 GG/LG errata.
MEM_INFO_PAGE_SIZE register containts invalid value in devices with
revision number lower than 18 and should not be used.
Change-Id: Idb2832246efcbbec2fd98a5c458f72a36df386fb
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1116
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When current tap state and end state are the same, transitions are added which is not what should happen.
The usbprog driver was already patched like this long time ago.
Change-Id: I339e87156bdc7b5c83c10c14025b749605d3871a
Signed-off-by: Roman Reichel <romanreichel@aol.de>
Reviewed-on: http://openocd.zylin.com/1113
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is only minimal support to enable use to catch a Hard Fault in
the stm32l flash bootloader.
Change-Id: I21d6a11893e2f1d173ebff1a651d6f52bf6eec32
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1103
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
Currently we have to supply the arg's to this cmd in a set order, this
change fixes that issue.
Change-Id: I14a15732e1917a91009e1ac14fba39ca1523c739
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/992
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Make sure we do not mask out the BFB2 boot bank bit, as this is used on
the larger XL devices.
Change-Id: Iacfdf874140e409e0c4ca9b9aee8f5c2f90dc9be
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/991
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The STM32F0 and F3 devices use a different default RDP to configure a
unlocked device, make sure we use that.
Change-Id: I170779461412c4c202c2cfc8d90baedb7e388150
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/984
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The user is able to use 2bytes of the options byte data for whatever
purpose they wish. Make sure we preserve this during an option erase/write.
Change-Id: Ibf951b11c59a148e671b1eb47fdc9b4f49ccae15
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/983
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Some debuggers (stlink) can't issue 16 bit writes and have to use a
loader to write flash memory.
Currently the loader is not used for option bytes, causing
stm32x_write_options to fail silently on such hardware.
Fix this by using stm32x_write_block to write option bytes as well.
Change-Id: I49c29d53ab5e162463cb349d4c89bef96467e587
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/480
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The current stm32lx driver will fail if no working area is
provided - fallback to using slow writes if this is the case.
Change-Id: I92b1535fec4aebc855c63ce2c54b10f168f3c07e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1007
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This part has 16k ram so make it all available.
Change-Id: Ifeb7bc850bfe4f68d0affb8f6a0931b4327e7257
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1006
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The smallest pert in the family has 10k RAM, so use that as a default
for the working area.
Change-Id: I78be0d14a254c109ac15a7163552c6132f810416
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1005
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Switch to using the internal HSI when a reset init is called, this also
matches the std stm32l cfg.
Read (verify) speed is increased from 17 to 120 KiB/s.
Change-Id: Ic94ba85949ffdefa17b7be45eef14e30f941d107
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1004
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The stlink/v2 has the ability to check the target voltage if the firmware
is recent enough (>= J13).
As a debugging aid we check the voltage at startup and issue an error if
this is too low to debug reliably.
Change-Id: I98e251f3880e31049c4307051c30bedd3451cf87
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/980
Tested-by: jenkins
Mathias K
Freddie Chopin
Spencer Oliver
Joerg Fischer
Johan Almquist
Franck Jullien
Evan Hunter
Hsiangkai Wang
Roman D
Roman Reichel
Andreas Fritiofson
Szymon Modzelewski