Commit Graph

700 Commits (3148bf838dc67c2b356a38fec6a979bc78ae2b0e)

Author SHA1 Message Date
EMARD dc415cb26c jtag: drivers: ft232r: unhardcoded
FT232R: introducing configurable parameters for pinout,
initial buffer size, state of RS232 signals at exit with
option to reattach kernel driver. All this was hardcoded before.
New parameters are documented in "openocd.texi" file.
Allows hopfully self-explainable and user-friendly adaptation to
various pinouts and similar chips like FT230X and FT231X.

Change-Id: Ib807f2ea3d4c1a164d351d65aeacd1978318d217
Signed-off-by: EMARD <vordah@gmail.com>
Reviewed-on: http://openocd.zylin.com/4681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-12-06 08:51:01 +00:00
Matthias Welwarsky 010b09121c armv7a: ARMv7-A MMU tools
factor out mmu-related code from armv7a.c, add a 'dump' command for
page tables.

Change-Id: Ic1ac3c645d7fd097e9d625c7c8302e7065875dd4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-11-08 09:10:09 +00:00
Dominik Peklo cea40152f8 flash/nor/stm32f1x: Use of protection blocks, improved option bytes handling
Handle write protection status in blocks instead of sectors, removing
unnecessary complexity in the process. Now closer to stm32f2x.
Support sequential modification of option bytes by read/modify/write
directly to option bytes area instead of always starting with the
currently loaded bytes from FLASH_OBR/WRPR registers.
Added new command 'options_load' to force re-load of option bytes w/o
having to power cycle target.

Change-Id: I5c76191e29c17a1e11482df06379d10ca8d6d04d
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4576
Tested-by: jenkins
Reviewed-by: Jan Vojtěch <honza.vojtech@gmail.com>
2018-11-03 11:18:18 +00:00
Steven Stallion 4ab75a3634 esirisc: support eSi-RISC targets
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.

Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-10-16 11:58:24 +01:00
Tim Newsome e2b6f347c7 Clarify what exactly the RISC-V code supports.
Change-Id: I8da657426cc52c738ab41bfb0164cbc6721c0aef
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4655
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-09-25 20:57:58 +01:00
Thomas Søhus b2d259f67c Added support for STM32L4X option bytes writing.
Enables the programming of Write protection lock bits.

- Updated/re-factored with option_read, option_write and option_load commands.

Change-Id: I86358c7eb1285c3c0baac1564e46da8ced5fd025
Signed-off-by: Thomas Søhus <tls@ceepro.dk>
Reviewed-on: http://openocd.zylin.com/4654
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-09-19 05:37:33 +01:00
Antonio Borneo 4423a58b4d doc: fix use of deprecated config file in the example
Commit 31c58c139d ("jtag: drivers: stlink: handle all versions with
single config") deprecates the use of "interface/stlink-v2-1.cfg" in
favor of a unique config file "interface/stlink.cfg".

Update the example in the documentation.

Change-Id: I1aed7c70e15f4edb4f81a3ee8e3bce575fde873b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4667
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2018-09-17 17:18:55 +01:00
Antonio Borneo ab858febb6 gdb_server: add per target option "-gdb-port"
The argument passed to global config command "gdb_port" is usually,
but not always, a TCP port number. In case of multiple targets, this
numeric value is used as the first port of a set of consecutive TCP
ports assigned one per target.
If the argument is not a numeric value (e.g. "pipe", "disabled", ...)
then incrementing it for the next target has no sense.

Add the option "-gdb-port number" to the commands "target create" and
"$target_name configure" to override, for the specific target, the
general global configuration.

This permits to use a per target "-gdb-port disabled", when no gdb
port is required for that specific target.

It also makes possible to choose a custom TCP port number for each
target, overriding the usual sequence of consecutive port numbers.

Change-Id: I3b9a1910b28ab4bc757e839d0e5d08ffc29f7ab4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4530
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-07 08:18:22 +01:00
Christopher Head 45f0c15912 doc: fix typo in cortex_m maskisr command
Change-Id: I37795c320ff7cbf6f2c7434e03b26dbaf6fc6db4
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4621
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-14 04:30:46 +01:00
Masatoshi Tateishi 9ec306e95a rtos: add support for NuttX
This patch introduces RTOS support for NuttX. Currently,
only ARM Cortex-M (both FPU and FPU-less) targets are supported.

To use, add the following lines to ~/.gdbinit.

define hookpost-file
  eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
  eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
  eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
  eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
  eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end

And please make sure the above values are the same as in
src/rtos/nuttx_header.h

Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com>
Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com>
Reviewed-on: http://openocd.zylin.com/4103
Tested-by: jenkins
Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01 14:33:50 +01:00
Antonio Borneo 6738e447c5 target/arm_adi_v5: add command "dpreg"
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.

Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
	$dap_name dpreg reg [value]

Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01 14:32:53 +01:00
Antonio Borneo 5e13e01141 server: explicitly call "shutdown" when catch CTRL-C or a signal
Every TCL command can be renamed (or deleted) and then replaced by
a TCL proc that has the same name of the original TCL command.
This can be used either to completely replace an existing command
or to wrap the original command to extend its functionality.
This applies also to the OpenOCD command "shutdown" and can be
useful, for example, to set back some default value to the target
before quitting OpenOCD.
E.g. (TCL code):
	rename shutdown original_shutdown
	proc shutdown {} {
		puts "This is my implementation of shutdown"
		# my own stuff before exit OpenOCD
		original_shutdown
	}

Unfortunately, sending a signal (or pressing CTRL-C) to terminate
OpenOCD doesn't trigger calling the original "shutdown" command
nor its (eventual) replacement.

Detect if the main loop is terminated by an external signal and
in such case execute explicitly the command "shutdown".
Replace with enum the magic numbers assumed by "shutdown_openocd".

Please notice that it's possible to write a custom "shutdown" TCL
proc that does not call the original "shutdown" command. This is
useful, for example, to prevent the user to quit OpenOCD by typing
"shutdown" in the telnet session.
Such case will not prevent OpenOCD to terminate when receiving a
signal; OpenOCD will quit after executing the custom "shutdown"
command.

Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4551
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01 14:31:37 +01:00
Tim Newsome a51ab8ddf6 Add RISC-V support.
This supports both 0.11 and 0.13 versions of the debug spec.

Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.

Flash support for the SiFive boards will also come in a later commit.

Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-07-24 13:07:26 +01:00
Edward Fewell 3e84da55a6 flash/nor: add support for TI MSP432 devices
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.

Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.

Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-07-18 21:09:23 +01:00
Edward Fewell 7b03129916 flash/nor: Add support for TI CC26xx/CC13xx flash
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.

Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.

Removed cc26xx.cfg file made obsolete by this patch.

Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
2018-06-15 20:06:25 +01:00
Andreas Färber 06123153f3 psoc5lp: Add NV Latch flash driver
Erasing is not supported by the hardware, it can be written directly.

Tested on CY8CKIT-059, except modifying-write.

Change-Id: I6e920ed930dcd5c7f0b10c5b1b4791a828d9080a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3434
Tested-by: jenkins
2018-06-06 18:12:21 +01:00
Andreas Färber f1427cca3c psoc5lp: Add EEPROM flash driver
Tested on CY8CKIT-059.

Change-Id: Ib02262e8eebf0df3d29492b8a7daa65b262da580
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3433
Tested-by: jenkins
2018-06-06 15:49:14 +01:00
Andreas Färber 2d5f2ede55 flash/nor: Add PSoC 5LP flash driver
Always probe for ECC mode and display ECC sectors if disabled.
Non-ECC write is implemented as zeroing the ECC/config bytes.
Erasing ECC sectors is ignored, erase-checking takes them into account.

Tested with CY8CKIT-059 (CY8C5888), except ECC mode.

Change-Id: If63b9ffca7ad8de038be3c086c49712b629ec554
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3432
Tested-by: jenkins
2018-06-06 15:48:33 +01:00
Edward Fewell d02de3a8a9 flash/nor: Add support for TI CC3220SF internal flash
Added cc3220sf flash driver to support the TI CC3220SF
microcontrollers. Implemented flash driver to support the
internal flash of the CC3220SF. The implementation does not
support the serial flash of the CC32xx family that requires
connection over UART, and not via JTAG/SWD debug. Added config
files for both CC32xx devices (no flash) and CC3220SF (with
flash).

Updated to implement comments from code review.
Additional updates to handle remaining comments from review.
Additional updates per review.

Added code to only request aligned writes and full 32-bit
words down to flash helper algorithm. Updated for recent
changes in OpenOCD flash code.

Removed cc32xx.cfg file made obsolete by this patch.
Change-Id: I58fc1478d07238d39c7ef02339f1097a91668c47
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4319
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-06-06 15:38:25 +01:00
Liviu Ionescu 2517bae6c1 Rework/update ARM semihosting
In 2016, ARM released the second edition of the semihosting specs
("Semihosting for AArch32 and AArch64"), adding support for 64-bits.

To ease the reuse of the semihosting logic for other platforms
(like RISC-V), the semihosting code was isolated from the ARM
target and updated to the latest specs.

The new code is already in use since January (in GNU MCU Eclipse
OpenOCD) and no problems were reported, neither for ARM nor for
RISC-V targets, after more than 7K downloads.

The 2 new files were formatted with uncrustify.

Change-Id: Ie84dbd86a547323bb8a5d24eab68fc7dad013d96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4518
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-06-04 09:16:08 +01:00
Edward Fewell 2ba27e2f3e jtag/drivers: Add support for TI XDS110 debug probe
Add support for the XDS110 debug probe using the APIs in the
probe's firmware. Includes support for older versions of the
firmware (with reduced performance) and support for a newer
version that includes OpenOCD specific APIs. Tested on various
TI LauchPads including MSP432P4, MSP432E4, CC2650, CC2652, and
CC3220SF.

Updated to add better support for swd switch. Removed issues found with
clang static analysis.

Updated to add rules entry for the XDS110 probe and Tiva DFU mode (which
affects both XDS110 and ICDI probes).

Change-Id: Ib274143111a68e67e80003797c6a68e3e80976b2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4322
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-05-31 13:25:16 +01:00
Antonio Borneo f0767a316a doc: fix several typos within manual documents
Mostly trivial fixes spotted by spell checker

Change-Id: I3af693faf5506c866e2abe253a0e37aea3c4d284
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4510
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-05-09 11:43:23 +01:00
Antonio Borneo aba11ae6e2 doc: fix several typos in openocd.texi
Mostly trivial fixes spotted by spell checker
One fix s/are/is/
No changes in the content of the document

Change-Id: Ic2d8696860c540e901e8c5190f8f1e7dce80545f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-26 06:43:18 +01:00
Tomas Vanek 81d0b769a6 target/cortex_m: allow setting the type of a breakpoint
Cortex-M target used 'auto_bp_type' mode. The requested type
of breakpoint was ignored and hard (FPB) breakpoints were set in
'code memory area' 0x00000000-0x1fffffff, soft breakpoints were set above
0x20000000.

The code memory area of Cortex-M does not mean the memory is flash and
vice versa. External flash (parallel or QSPI) is usually mapped above
code memory area. Cortex-M7 ITCM RAM is mapped at 0. Kinetis
has a RAM block under 0x20000000 boundary.

Remove 'auto_bp_type' mode, set breakpoints to requested type.

Change 'cortex_m maskisr auto' handling to use a hard temporary
breakpoint everywhere: it can also workaround not working soft breakpoints
on Cortex-M7 with ICache enabled.

Change-Id: I7a9f9464c5e10bfd7f17cba1037ed07a064fa2e8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4429
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-12 20:49:18 +01:00
Tomas Vanek 414213a5ea target/arm_adi_v5: extend apcsw command to accept arbitrary bits
apcsw command was limited to SPROT bit only.

Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7

Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-07 20:31:37 +01:00
Tim Newsome 2e2bb14b27 Add gdb_report_register_access_error command
With this option enabled (it's disabled by default) errors accessing
registers are returned to gdb. Otherwise they are ignored and success is
reported to gdb. (This is the current behavior.)

We want this for RISC-V, but there's still some cleanup that needs to be
done before that can be upstreamed.

Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I7e56109ea52d18b780c14a07fb35f9e6e8979da4
Reviewed-on: http://openocd.zylin.com/4452
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
2018-04-07 20:31:14 +01:00
Matthias Welwarsky 0dba1815e6 arm_adi_v5: Add ability to ignore the CSYSPWRUPACK bit
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.

Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-07 20:30:12 +01:00
Stefan Arnold be87994d60 flash/nor/at91samd: Add "nvmuserrow" command.
Add option "nvmuserrow" to "at91samd" for changing and reading the register at 0x804000 which represents various fuses.

Change-Id: I6382cc4ac15e6b9681e2f30b0ae60397a6289c3b
Signed-off-by: Stefan Arnold <sarnold@sh-sw.de>
Reviewed-on: http://openocd.zylin.com/4260
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-06 10:37:31 +01:00
Matthias Welwarsky 2231da8ec4 target: restructure dap support
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
  instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
  longer references the dap, daps are now independently
  created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
  power cycle)
- update documentation
- update target files

Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 09:58:21 +01:00
Matthias Welwarsky f444c57bf2 arm_cti: add cti command group
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.

Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 09:48:03 +01:00
Paul Fertser 828ee07657 server: bind to IPv4 localhost by default
Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.

If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.

Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
2018-03-18 12:59:43 +00:00
Paul Fertser 437925c141 doc: fix xref texinfo warning
Change-Id: Iff1ba5836e3a4f352903c3a5ae73c7d992306d42
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4466
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
2018-03-15 13:40:53 +00:00
Tomas Vanek 6f700d2b1c doc: make gdb-attach description understandable
Change-Id: I31babf4e3bbe7c94f26818d938699562a4a26d48
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4465
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-03-13 10:55:35 +00:00
Matej Kogovsek ffb93ef371 jtag: drivers: add support for FT232R sync bitbang JTAG interfaces
Change-Id: Ib88a9e270f5c2a50902a137bcc97fdefd5aad1c6
Signed-off-by: Matej Kogovsek <matej@hamradio.si>
Reviewed-on: http://openocd.zylin.com/4215
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-03-13 08:47:46 +00:00
Tomas Vanek 396ea7c8dd doc: update openocd.texi after change of gdb-attach default value
While on it
- change some occurrences of gdb to GDB if it refers GDB software
  (as oposed to a gdb command)
- add some xrefs
- give more meaningful example of target event definition
- remove obsoleted example of GDB hook-step

Change-Id: Ia2e26021d57f675acfa1de704f6c3e81c22bb8bf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4444
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-12 14:12:21 +00:00
Michele Sardo cb2f21bf36 Added support for STMicroelectronics BlueNRG-1 and BlueNRG-2 SoC
Added configuration files and flash loaders.

Change-Id: I768eb3626f4e0eadb206bef90a867cc146fe8c75
Signed-off-by: Michele Sardo <msmttchr@gmail.com>
Reviewed-on: http://openocd.zylin.com/4226
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-03-07 23:40:55 +00:00
Tomas Vanek bb9d9c6026 target: use correct target in target-prefixed commands and event handlers
This change contains an alternative to Matthias Welwarsky's #4130
(target-prefixed commands) and to #4293 (event handlers).

get_current_target() must retrieve the target associated to the current
command. If no target associated, the current target of the command
context is used as a fallback.

Many Tcl event handlers work with the current target as if it were
the target issuing the event.

current_target in command_context is a number and has to be converted
to a pointer in every get_current_target() call.

The solution:
- Replace current_target in command_context by a target pointer
- Add another target pointer current_target_override
- get_current_target() returns current_target_override if set, otherwise
	current_target
- Save, set and restore current_target_override to the current prefix
	in run_command()
- Save, set and restore current_target_override to the event invoking
	target in target_handle_event()

While on it use calloc when allocating a new command_context.

Change-Id: I9a82102e94dcac063743834a1d28da861b2e74ea
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4295
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-03 08:40:09 +00:00
Bohdan Tymkiv e9f54db003 Add support for Cypress PSoC6 family of devices
* Tested on CY8CKIT-001 kit with PSoC6 daughter board.
* Tested with several J-Link adapters (Ultra+, Basic)

Change-Id: I0a818c231e5f0b270c7774037b38d23221d59417
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4233
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-02-14 08:27:30 +00:00
Tomas Vanek c2b2a7a3b8 Kinetis_ke: add KEAx family to texi and cfg comment
Change-Id: Id8f676b027f57fc540473c1a3a01bdd2ec49a200
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4232
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
2018-02-01 19:38:49 +00:00
Paul Fertser ab597027ea doxygen: fix issues with recent Doxygen versions
This fixes parsing of several documentation files which do not have
dot in the filename.

style.txt change fixes doxygen warnings and ensures proper display of
comment begin/end instructions in HTML.

Tested with Doxygen 1.8.13.

Change-Id: I9fd9ac3b51b47076b8fdbd3e93b90c3eba9b9631
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4342
Tested-by: jenkins
2018-01-30 07:35:50 +00:00
Matthias Welwarsky b3d29cb544 aarch64: add 'maskisr' command
Allow to configure ISR masking during single-step and add
handling for stepping over WFI with ISR masked.

Change-Id: I7918be7bcda6a1d9badac44fc36c59b52f662fef
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4023
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-01-16 09:05:41 +00:00
Robert Jordens 867bdb2e92 jtagspi: new protocol that includes transfer length
This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:

1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:

  The previous logic was erroneous. The delay in clock cyles from a bit
  written to the jtag interface to a bit read by the jtag interface is:

  * The number of BYPASSed TAPs before this (jtagspi) tap
  * The length of the jtagspi data register (1)
  * The number of BYPASSed TAPs before this one.

  I.e. it is just the number of enabled TAPs. This also gets rid of the
  configuration parameter DR_LENGTH.

3. Use marker bit to start spi transfer

  If there are TAPs ahead of this one on the JTAG chain, and we are in
  DR-SHIFT, there will be old bits toggled through first before the first
  valid bit destined for the flash.
  This delays the begin of the JTAGSPI transaction until the first high bit.

4. New jtagspi protocol

  A JTAGSPI transfer now consists of:

  * an arbitrary number of 0 bits (from BYPASS registers in front of the
    JTAG2SPI DR)
  * a marker bit (1) indicating the start of the JTAG2SPI transaction
  * 32 bits (big endian) describing the length of the SPI transaction
  * a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
  * an arbitrary number of cycles (to shift MISO/TDO data through
    subsequent BYPASS registers)

5. xilinx_bscan_spi: clean up, add ultrascale

This is tested on the following configurations:

* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
  adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
  Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E

Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-01-13 19:36:42 +00:00
barthess dc28a6e593 XCF (Xilinx platfrom flash) support.
Change-Id: I4ee6db5f0abdb9fd279cc0edd13f71952a9d295d
Signed-off-by: Uladzimir Pylinski <barthess@yandex.ru>
Reviewed-on: http://openocd.zylin.com/3914
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-01-13 09:13:14 +00:00
Paul Fertser 99b03d3bfb doc: add SVF optional arguments descriptions
Change-Id: I1a3e5b04b6bc4821c4d11c8fcb33b426d6d41bfb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4314
Tested-by: jenkins
Reviewed-by: Jim Norris <u17263@att.net>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
2018-01-13 08:45:35 +00:00
Tomas Vanek 19f8f58c0d target: remove unused event definitions
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.

Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2017-12-12 21:18:10 +00:00
Spencer Oliver 0422763489 doc: improve stm32 flash driver documentation
also remove legacy footnote as it adds no value.

Change-Id: I3892acf244bd8fba6f844a5d82a66004e193a395
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4309
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
2017-12-12 21:15:09 +00:00
Paul Fertser 31c58c139d jtag: drivers: stlink: handle all versions with single config
Extend HLA interface to allow multiple VID/PID pairs and use it to
autodetect the connected stlink version.

Change-Id: I35cd895b2260e23cf0e8fcb1fc11a78c2b99c69b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3961
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2017-12-12 21:13:55 +00:00
Spencer Oliver 9021210428 docs: add missing stm32 flash driver documentation
Change-Id: I433780646e6fdfd0c2527b4a68025946ccb79d8b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4307
Tested-by: jenkins
Reviewed-by: <alexandre.torgue@st.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2017-12-07 11:14:10 +00:00
Alexandre Torgue 6a66cccbad flash: Add new stm32h7x driver support
Add basic support for:
     -STM32H7x (Embedded flash 2M)

Erase and write tested on stm32h743.

Change-Id: Ie8d8786227cdeee39fcf5663167a053ad8dcef4c
Signed-off-by: Rémi Prud'homme <remi.prudhomme@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-on: http://openocd.zylin.com/4181
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2017-12-06 21:29:10 +00:00
Andreas Fritiofson ef49b34b2a arm: semihosting: set command line arguments
Add "arm semihosting_cmdline [argv0 argv1 ...]" for setting the
command line arguments for the debuggee.

[andreas.fritiofson@gmail.com]: Dynamic allocation, empty default

Change-Id: I831ddd161d602f251940e29608a154e9590fdee1
Signed-off-by: Christian Groessler <chris@groessler.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3106
Tested-by: jenkins
2017-10-22 23:06:09 +01:00