'at91samd chip-erase' command did not work on secured device.
Fix it changing address of DSU.CTRL register
(see Atmel SAM D21 datasheet, 13.9. Intellectual Property Protection).
While on it check error return of DSU.CTRL write.
Change-Id: I83155a634a5458cdc0cc16c99c0e155eb1d8b3d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Thomas Irmen <tirmen@gmx.net>
Reviewed-on: http://openocd.zylin.com/4043
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Adapter clock frequency is set by 32-bit number and most adapters
limit the highest speed safely. There is no reason to impose strict
limit of 5000 kHz if some adapters can do more.
While on it give informative error message in case of zero adapter_khz.
Change-Id: I45c9804678e24496ea769ea9ca6036701b04dde9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3945
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Fail if we fail to set debug level. Also, clarify in usage string that
-d<n> doesn't accept spaces.
Change-Id: I9ea9945dc068e3e7cfd18b16ffa2a29366d6e4d1
Signed-off-by: Girts Folkmanis <opensource@girts.me>
Reviewed-on: http://openocd.zylin.com/3880
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds the file ti_beaglebone-base.cfg as the common base
configuration for all TI BeagleBone derived boards. It also modifies
ti_beaglebone.cfg to source the base board and only add the on-board
JTAG adapter. Lastly, it adds a file ti_beaglebone_black.cfg with
a suitable configuraton for the BeagleBone "Black" variant.
Change-Id: I40cacb8abed7bdb308929713891f7b5e5b685c95
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3099
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add new entry in nrf51_known_devices_table for nRF51822 chip found on
chinese Core51822 dev board. The chp has markings N51822 / QFAAH1 / 1630FW
Nordic Semiconductor nRF51 Series Compatibility matrix confirms that this chip
has 256K Flash and 16K RAM.
Change-Id: I571d15913c6f6e02a6f09c883d7dfc5a66b57c28
Signed-off-by: Damyan Mitev <damyan_mitev@mail.bg>
Reviewed-on: http://openocd.zylin.com/4091
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Without the change Atmel EDBG uses default clock freq about 168 kHz
instead adapter_khz configured before interface init.
Changing adapter speed after init works as expected.
Testing shows the EDBG firmware resets speed to default during DAP_SWJ_Sequence.
Tested with fw versions 03.1F.01AE and 02.09.0169
This change repeats the DAP_SWJ_Clock command after sending a SWJ sequence.
Change-Id: Ic70457c5df635f47cad5e70b0dc83a083ea1b3a3
Reported-by: Ladislav Laska <laska@kam.mff.cuni.cz>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3944
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
There is nothing the user can do if their device does not support sector
programming, there is no reason to have this message at warning level.
Change-Id: Ic9b7386e59b64fece7fbfdc543bdfeeed3eae73d
Signed-off-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-on: http://openocd.zylin.com/4105
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Increasing the trace buffer size on the st-link itself gives openocd a greater
chance of avoiding trace data overflowing within the st-link between polls
when there is a large amount of data being sent over the trace port
The st-link appears to split the given buffer size in half
while one half is awaiting transfer over USB, the other half is being
filled by DMA transfer. If you do not poll frequently enough, the DMA
transfer will overflow back to the start of its current buffer, resulting in
corrupted output
Buffer size of 4096 bytes is the maximum allowed by the st-link v2
Change-Id: I169189b021c34f8d18de1601d78b8c5890367d68
Signed-off-by: Austin Morton <austinpmorton@gmail.com>
Reviewed-on: http://openocd.zylin.com/4085
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
document aarch64 specific commands and common ARMv7 and v8 DAP commands
Change-Id: Icbb76209735ec734f2e67f82bfc7270edb40ad0b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4008
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The halt event was left pending in the CTI, better to clear it immediately
after debug entry.
Change-Id: I6002f862681baf98769e3c73332a7f7f0ef938c1
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4030
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Int may not be 32 bit long.
Change-Id: I420f7efeb484eb35c1d7c20e1575b0b31ed8c9ff
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3930
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When ARM64 support was being merged, a comparison ended up being
inverted. This causes NULL pointer access when target attempts to
use core cache.
Change-Id: Ic8873ddd13dbdd8100856a71b4717f44cd336e23
Signed-off-by: Girts Folkmanis <opensource@girts.me>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4042
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
configuration covers all 8 Cortex-A53 cores and auxiliary Cortex-M3
used for power management.
Change-Id: I5509f275aa669abe285f9152935ecdcbcd0c402e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4009
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
after handling of an exception in debug state, immediately
restore the original core state.
Change-Id: Ie53b63c9f19815f717f4df4390fbc13f0a204cc2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3996
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
to speed up debugging, don't load the complete register context
on a halt event, load only those registers that might be
clobbered during debugging.
Change-Id: I0b58e97aad6f28aefce4a52e870af61e1ef1a44f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3995
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
small changes to correct code formatting and spelling of some
log messages.
Change-Id: I645e675f8f9f4731b0271ddc55f64e8cf56ec1db
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3994
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch contains a major overhaul of the target run control,
mainly for the sake of satisfying gdbs ideas of how a target
should respond to various control requests for the debugger.
The changes allow gdb a slightly better control on how cores
are stepped: a core can be single-stepped while
other cores remain halted or continue normal execution
until the single-stepped core halts again.
Also, on any halting event (user command or breakpoint) the
system is brought into a stable state with all cores halted
before the halt is signaled to the debugger.
This patch also transitions the target code to make use of the
new CTI abstraction instead of accessing CTI registers directly.
Change-Id: I8ddc9abb119e04580d671b57ee12240c3f5070a0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3993
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
- rename "cortex_a" command group to "aarch64"
- remove default blank check, checksum and algorithm hooks
since they're not going to work in aarch64 mode anyway.
Change-Id: Ieb0046786ed9425baf6774c68f42a8285cc2aefd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3991
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Make sure all core register caches are invalidated on reset
assert, make sure to re-init debug registers on deassert.
Change-Id: I82350d04cc3eaae5e35245d13d6c1fb0a8d59807
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3990
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
introduce armv8_set_dbgreg_bits() function to make register
bit-field modifications easier to read.
Change-Id: I6b06f66262587fd301d848c9e0645e8327653de7
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3989
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The aarch32 register cache is only a separate view of the aarch64
registers. Load aarch32 registers through their aarch64 equivalents.
Change-Id: I3e932dfb782f03d73d30d942b24db340a5749e47
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3988
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Mmu faults can not be prevented on aarch64, they need to be taken and
handled accordingly. Remove the remaining stub code.
Change-Id: I6241efa594fe6b963624f9628cdf1c8e46588223
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3987
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Not specific to ARMv8, the Cross Trigger Interface
deserves an independent access wrapper.
Change-Id: I84f8faad15ed3515e0fff7f6cc5d1109ef91a869
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3986
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Replace loop by right-shift.
Inspired by patch from Alamy Liu
Change-Id: I1285f4f54c0695a93fa42e9863ed8ffa4de00f70
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3985
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Suppress some very verbose LOG_DEBUG's that are not really useful
any more.
Change-Id: I67f10ba9510a9e34a027f378f4b62b8901ddc8a4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3984
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reduce SLOCs in SCTLR retrieval and modification functions and make them
less complex.
Change-Id: Ida1a99c223743247f171b52eef80dc9886802101
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3982
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use the correct opcode for Aarch32 state, both for the breakpoint
instruction itself and the cache handling functions.
Change-Id: I975fa67b1e577b54f5c672a01d516419c6a614b2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3981
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with a Dresden Elektronik deRFmega128 module.
Change-Id: I91da3b11b60e78755360b08453ed368d6d396651
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2790
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
At framework level, the resume hook is not protected. Make sure to
not attempt a resume if the target is not halted.
Change-Id: I4dd1975a95d6c513bd4f4e999e496bc11182a97a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Basically port a fix that was already done for the cortex_a target.
Change-Id: I4cf4519159bda03ed611bc0b2e340a5dad2d85fe
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Instead of supplying a local, preinitialized "dscr" variable, use the
cached value from arm_dpm, which is kept up-to-date anyway.
Change-Id: I06d548d4dc6db68b9d984c83ed026fa9069d7875
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
arm commands are mostly unusable anyway, remove them. to be replaced
by aarch64 specific commands later
Change-Id: Ie994771bc0e86cff1c26f68f1f51ce8ec352a509
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
"currentel" special register is not accessible in debug state.
Change-Id: I9022b01b423cd9ae8227ed018d6166078ba44832
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Make debug and error messages more informative, fix spelling and
formatting errors
Change-Id: I7245f42c5153bcc95676270814d30e91c113aaed
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
struct arm_reg::value[] must be 8 byte to hold a 64bit register value.
Change-Id: If253e90731d0ee855eafd9d7b63b91f84630cc7c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move clearing of DSCR "Sticky Error" condition to the
exception handling function. Clear once on entering debug state.
Change-Id: Iec1d09d6f2d9cdd7e92953da5ea19f3e399ca12c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
recommended for Corte-A8 cores, not sure if necessary
for ARMv8 based cores as well.
Change-Id: Ibcb36170c5fac6a6b132de17f734c70a56919f9b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Remove register cache invalidation and target state changes that are
handled appropriately in other functions.
Change-Id: Ic903f41ddc267f4b8765ea022bd4d6da1017e21f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When a PE is in Aarch32 state and gdb asks for a target description,
provide a register view compatible with the "org.gnu.gdb.arm.core"
feature. Only current-mode registers are exported, banked registers are
not visible.
Change-Id: I99a85d94831cf597fe8cff6a0a1818ce0a33613b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to TTBR in EL0. Circumvent by moving the PE to EL1
before reading, and switch back to original mode afterwards.
Change-Id: I22891b958d3d7e6fad1cb27183c192d975d63d89
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Tomas Vanek
Jerome Lambourg
Girts
Matthias Welwarsky
Damyan Mitev
Chengyu Zheng
Matthias Bock
Joakim Nohlgård
Marc Schink
Austin Morton
Matthias Welwarsky
Andreas Fritiofson
Karl Palsson