flash programming via flash write_image or gdb load would
produce a bogus error message that the flash chip was to
small.
The solution is to limit the current flash programming
run to the current chip.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
SMI interface hides the real SPI bus between SPEAr and
external flash.
Added comments to highlight the SPI operation, to help a
future rework in SPI generic and SPEAr specific drivers.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
this never panned out and there are enough mistakes in
the code that probably nobody used this.
Use the tcl server and implement a standalone http
app instead works fine.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add comments to assembly flash loader for STM32. Add tiny improvement in
size of the algorithm (40 vs 48 bytes) and tiny speed improvement (~1.5%,
as time is wasted on waiting for end of operation anyway).
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
gdb connect can fail when the flash has not been probed.
During gdb connect, the flash layout is reported, but this
can not be automatically detected for a target that is
powered up and OpenOCD supports connecting to gdb server
even if the target is powered down.
The solution is to turn of the gdb_memory_map feature.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the CPU crashed at some point, poll will discover this.
Previously the poll fn would clear the error and print a warning,
rather than propagating the error.
The new behavior is to report the error back up, but still
clear the error.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Document "-n" option in manual;
Modify "echo" command definition as COMMAND_HANDLER to
easily add help message
Add help message aligned with manual.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
With the new JIMTCL, "puts" only writes to stdout.
To write on telnet port too, "echo" must be used.
This patch gives to "echo" similar commandline option of "puts".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
add missing error handling.
Output warning when assuming maximum flash size in the
family when failing to read.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Initial support for ST SPEAr310 and for the evaluation
board EVALSPEAr310 Rev. 2.0.
Scripts are split in generic for SPEAr3xx family and
specific for SPEAr310. This should easily allow adding
new members of the family.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch introduces support for Cortex A8 based Freescale i.MX51 CPU. This CPU
has the Debug Access Port located at a different address (0x60008000) than TI
OMAP3 series of CPUs.
i.MX51 configuration file based on OMAP3 configuration file and an email from
Alan Carvalho de Assis <acassis@gmail.com>.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Implement autodetection of debug base. Also, implement a function solving
various hardware quirks (like iMX51 ROM Table location bug).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch implements "dap_lookup_cs_component()", which allows to lookup CS
component by it's identification.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch adds function called "dap_detect_debug_base()", which should be
called to get location of the ROM Table. By walking ROM Table, it's possible to
discover the location of DAP.
Sadly, some CPUs misreport this value, therefore I had to introduce an fixup
table, which will be used in case such CPU is detected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
So far most of the people have been using existing ARM966E in the
place of ARM946E, because they have practically the same scan chains.
However, ARM946E has caches, which further complicates JATG handling
via scan-chain. this was preventing single-stepping for ARM946E when
SW breakpoints are used.
This patch thus introduces :
1) Correct cache handling on memory write
2) Possibility to flush whole cache and turn it off during debug, or
just to flush affected lines (faster and better)
3) Correct SW breakpoint handling and correct single-stepping
4) Corrects the bug on CP15 read and write, so CP15 values
are now correctly R/W
measure_clk indicates ca. 3-4MHz, so 1MHz should be safe.
Added self_test proc used to test that rclk worked.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
help would not show help for commands when the command
interpreter was in the wrong mode, which means that
e.g. "help newtap" didn't work, it wouldn't show the
"jtag newtap" help as it was a configuration command.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Collect variable definitions.
Report syntax error to command dispatcher.
Propagate error when unable to open file.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Antonio Borneo
Øyvind Harboe
Freddie Chopin
Andrew Leech
Marek Vasut
ddraskovic
Spencer Oliver
Peter Stuge
Michal Demin