Doc (mostly) update for jtag_khz:
- switch to @deffn syntax
- add entry for "jtag_rclk"
- move deprecated "jtag_speed" into collection of deprecated calls
And for ft2232, don't be the only adapter to *log* an error if RTCK
is requested; it's already reported properly, like any other nonfatal
command parameter. "jtag_rclk" just works as expected, without any
scarey messages.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1910 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Make startup for the various server ports be quiet, unless
debugging is active: don't emit needless scarey messages.
Update the relevant documentation and its references:
- For these port commands ... cover the default values;
convert to @deffn syntax; include their use outside of
the configuration stage; and alphabetize.
Similar updates to the rest of that small chapter:
- Highlight that there even *IS* a configuration stage, after
which some command functionality is no longer available.
- For GDB commands ... convert to @deffn syntax; alphabetize;
include a missing command (!); add missing helptext (!) for
one non-missing command; update relevant cross-references
and index entries.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1909 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update two oddball NAND commands to work with {offset, length}
instead of block numbers, matching the other commands as well
as usage in U-Boot and the Linux-MTD utilities.
Document them accordingly. Update the single in-tree use of
those commands (sheevaplug).
ALSO:
(a) Document the current 2 GByte/chip ceiling for NAND chipsize.
(32 bit offset/length values can't represent 4 GBytes.) Maybe
after the upcoming release, the code can switch to 64-bits.
(b) The "nand check_bad_blocks" should report "bad" blocks. They
are not "invalid" blocks; they're "bad" ones.
(c) Tweak the "nand info" command to handle the "no arguments"
case sanely (show everything, instead of showing garbage) and
not listing the blocksize in hex kbytes (duh).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1904 b42882b7-edfa-0310-969c-e2dbd0fdcd60
NAND support for DaVinci-family drivers, with HW ECC support.
Declare the NAND chip on the DM355 EVM board.
Currently tested on DM355 for Linux interop using the standard
large page (2KB) chip in the EVM socket; "hwecc1" and "hwecc4"
work fine. (Using hwecc4 relies on patches that haven't quite
made it through the Linux-MTD bottlenecks yet.)
Not yet tested: 1-bit on small-page (although it's hard to see
how that could fail); 4-bit on small page (picky layout issues);
the "hwecc_infix" mode (primarily for older boot ROMs; testing
there is blocked on having new bootloader code).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1903 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Fix minor issues with xrefs not liking parentheses around them.
- Change 'Building' section to 'Building OpenOCD'. It reads better.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1902 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Remove style guide from user guide; moved to doxygen manual.
- Replace with improved introduction for developers and packagers.
- Move introductory paragraph about the project under the About page.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1895 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add a "NAND Commands" section to to the TEXI docs, covering the basic
commands except for those previously discussed as being due for removal
("nand copy") or switching to use byte offsets not block numbers.
This uses the "@deffn..." syntax for defining commands, as somewhat
suggested by the TEXI documentation, and adds a new "Command Index".
We might prefer to merge those indexes for the near term, but I think
the "@deffn" approch is probably worth switching to.
Updates a few other bits to clarify that "flash" doesn't just mean NOR.
And to fix one niggling falsity: the "reset-init" event *is* used, and
in fact it's quite important.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1879 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Explicitly mention autoconf >= 2.59 as requirement (as per
configure.in). Also automake >= 1.9 (though I'm not sure which
if that's really the minimum requirement).
- Document various missing configure options.
- Fix various typos and inconsistencies.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1426 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- updated missing jtag dongle url's in texi
- reformat and remove whitespace from last commit
git-svn-id: svn://svn.berlios.de/openocd/trunk@1227 b42882b7-edfa-0310-969c-e2dbd0fdcd60
zwelch
kc8apf
oharboe
ntfreak
duane