This access port type comes with the AMBA 5 protocol specification,
see 'C1.3 AP' in ARM IHI 0031D.
Change-Id: I3c4f0a69230daaf4f5f979de6213fe3c025a089a
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also
adds configuration file for SSE-200 based Musca A board. Flash programming
support for Musca A QSPI flash is still not functional. This configuration
will be updated once that support lands into OpenOCD.
Please refer to ARM documentation for more information about SSE-200 and
Musca A.
Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/5006
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds ARMv8-M CPUs detection logic in ARMv7m target specific code.
Also adds a slightly different watchpoint manipulation logic for ARMv8-M.
This is based on ARMv8-M architecture reference manual.
Tested on ARM Musca A board.
Change-Id: I0652560954ef02c378a7067fab586edf39d3e9cc
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4997
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I1b917a4c1205115c4e0315373d81a9305e931258
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4944
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I32c43e2e47366363521fa3f387de9e2fb1c20852
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4943
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of jtag's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition.
It can be tested running openocd on a jtag target and adding a
jtag event "setup" with a single line "return", e.g.
openocd -f board/ti_cc3200_launchxl.cfg \
-c 'jtag configure cc32xx.cpu -event setup return'
to get the message:
../src/jtag/core.c:1599: Error:
in procedure 'jtag_init' called at file "../src/jtag/core.c",
line 1599
Modify jtag_tap_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I6d6febc15ef169638afffbffc1810e0b84fcf5c8
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5199
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of target's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition, thus dumping the
call-trace. The execution is not stopped because the error is not
further propagated, but the error message is annoying and
misleading.
It can be tested running
openocd -f ./test.cfg
using the following script "test.cfg". You can replace the board
file in line 1, to use a board available in your lab:
1 source [find board/st_nucleo_f4.cfg]
2 [target current] configure -event reset-start {}
3 [target current] configure -event reset-end {return}
4 init
5 proc a {} {[target current] invoke-event reset-start}
6 proc b {} {[target current] invoke-event reset-end}
7 proc c {} {a;b;echo "arrived at the end"}
8 c
9 shutdown
The execution produces:
./test.cfg:7: Error:
in procedure 'c' called at file "./test.cfg", line 8
in procedure 'b' called at file "./test.cfg", line 7
arrived at the end
that shows the call-trace but does not halt the execution.
The developer can avoid using the "return" command in the event
body by defining a TCL procedure that implements the handler and
that contains the "return" command, reducing the handler body to
a simple call to the procedure above. But this approach is either
not documented nor always intuitive while writing the handler,
causing waste of time to look for the false error.
Modify target_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I2b860bab7233c6ed13ee4098e348d7533e1c4626
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4974
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c2e18bfaea changed the size of the JTAG-to-SWD sequence
from 15 bytes to 17 bytes. This broke SWD switch sequence transfer
for buspirate, since buspirate packets can only hold a payload of up
to 16 bytes and we tried to fit the whole sequence in a single packet.
Splitting up the sequence transfer in appropriately sized packets
makes buspirate SWD work again (successfully tested with buspirate
firmwares v6.1 and v7.0).
Change-Id: Ib5b412b9e77287d705d2762e31c16d30318b50e3
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Reviewed-on: http://openocd.zylin.com/5200
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If1f56fd5d610b993a4ecbc900fac9f90638037c9
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5202
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit 877cec20dc
("command: check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The command '$_TARGET configure -xxx' was therefore applicable on running
OpenOCD to change the target configuration. It is handy e.g. for changing
an event handler or changes of the work area.
Change 'configure' command .mode to COMMAND_ANY to make it possible again.
The only parameter which cannot be re-configured after init is -gdb-port.
Test the command mode and refuse setting of gdb port after init.
Change-Id: I88493ac10a46647dc52a88fbc9f8ce6b5ba3bcd0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5214
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
since b5964191f0, all XScale-specific registers were missing, breaking
config scripts.
Change-Id: Ia56f3ca17500ba54bd08f417e9a5aaaa8a1be8c4
Signed-off-by: Michael Schwingen <spam-openocd@discworld.dascon.de>
Reviewed-on: http://openocd.zylin.com/5136
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro TARGET_ADDR_FMT, defined in helper/types.h, already
includes the prefix "0x" in front of the hexadecimal number,
being defined as:
#define TARGET_ADDR_FMT "0x%8.8" TARGET_PRIxADDR
An additional "0x" is present in mem_ap; it prints debug messages
with a double "0x" before the address:
Debug: 2921 34180 mem_ap.c:153 mem_ap_write_memory():
Writing memory at physical address 0x0x5000000c; size 4;
count 1
Remove the incorrect hexadecimal prefix.
Change-Id: I38f19ed2a2f542bd5df53e947a2604f1cbe80e08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5222
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
To support 128 bit registers, the rtos_reg structure value
array needs to be updated from 8 to 16 bytes.
Tested by reading ARMv8 NEON FP regs on an Ampere eMAG 8180 with GDB.
Change-Id: I7f3fe1a5b2def599d021787fbe9cdd51f92859a4
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5209
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The ARMv7-A architecture supports super sections which allows mapping
physical addresses up to 40-bit into a 32-bit virtual address using the
short descriptor format (see ARM DDI 0406C.c section B4.1.112 for
details).
Change-Id: I8e64d0e93e36ae7a7da7b7bf2a8342856bb044f1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5212
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In preparation for adding super section decoding, do not restrict
armv7a_mmu_translate_va_pa() to 32-bit virtual addresses since ARMv7-A
processors with VMSA extensions (including LPAE) can issue wider
physical addresses. Update casting to uint32_t where necessary.
Change-Id: Id1c3d0d5ac324cbdc334259d9ea75fe4981671a1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5211
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function is not used anywhere in the tree, remove it, such that we
only have a single function moving forward that might need to deal with
short vs. long format specifics.
Change-Id: I80e81cd7eba1e028d1afaeaedb675b46c0ca6fa1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Check earlier that the read of the PAR register was successful instead
of starting the decoding and then checking for an error reading that
register.
Change-Id: Id96c2b2f76d2d1c745fcfa55ad4c1e6db92106f9
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The prefixed commands has been removed in commit 0840414f0e
("helper/command: do not replace new commands with ocd_ prefix").
Change-Id: I9f101beb85533973041386896bbb215bb141962f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5191
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The prefix is not necessary anymore.
Change-Id: Ie0df06a70ff51e6719d7564396739d28618b0196
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5190
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
armv7m_get_core_reg() calls arm->read_core_reg()
arm->read_core_reg() expects the register number as an index
to core reglist, not an ARMv7M specific register code.
Use reg->number instead of armv7m_reg->num.
The change solves assert
src/target/armv7m.c:222: armv7m_read_core_reg: Assertion
`num < (int)armv7m->arm.core_cache->num_regs' failed.
when gdb 'info reg' is issued on a Cortex-M target and
no cortex_m_debug_entry() has been called since OpenOCD start
(target was halted before OpenOCD start).
Change-Id: I32a2294693ef979b613be93aeceb3b0eb06ee6df
Ticket: https://sourceforge.net/p/openocd/tickets/216/
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For legacy support, drivers that do not define a list of
transports get identified as jtag_only.
Cleanup this old crust and initialize properly the transports
field in the jtag_interface for all the drivers.
Change-Id: I9c86064e5d05bd0212bc18f4424414e615e617fe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In the initial commit 6c9b804d61
in 2007's svn://svn.berlios.de/openocd/trunk@246
a target script gdb_program_config was called before gdb flash
programming. To guarantee the script does not left any pending
command in the jtag queue, a call to jtag_execute_queue() was
inserted after the execution of the script.
In following commit ef1cfb2394
in 2008's svn://svn.berlios.de/openocd/trunk@975
the script was replaced by the event "old-gdb_program_config" and
the call to jtag_execute_queue() get executed in every case, even
if the event handler was not present.
At last, commit bb3793c9a4
("target: remove legacy target events") stripped away the
obsolete event but left the call to jtag_execute_queue(), now
completely useless.
Remove the call to jtag_execute_queue() and clean-up the code
around it.
Change-Id: I284f54d656d431ad6cdc25ca18218c09db31bd25
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4911
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since the first commit 09883194f8 that introduced cortex_m, the
code has a delay of 50ms after srst has been asserted.
The specific delay is implemented through the JTAG_SLEEP command
sent in the jtag queue.
To remove the dependency from the jtag queue, replace the delay
with a transport independent function.
In case of jtag transport, this change keeps the same behaviour
only if the jtag queue has been flushed before the delay. This
does not happen if the call to dap_dp_init(), few lines above,
fails while calling a dap_queue_dp_{read,write}(); in this case
the jtag queue will be flushed later, after the delay, while in
the original code the delay would follow the flushing of the
commands already queued. Anyway, this different behavior would
only happen in case of DAP already not responsive so anticipating
the delay in such error condition is not supposed to add further
problems.
Change-Id: If15978246764e4266b10e707d86c03e5ed907de7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4912
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is just a single entry point for the jtag API .khz(),
.speed_div(), .power_dropout(), .srst_asserted().
Simplify the code by in-lining the default handler.
The overall code behaviour is not changed.
This change prevents modifying at run-time the content of
struct jtag_interface.
Inspired from change http://openocd.zylin.com/943
by Evan Hunter <ehunter@broadcom.com>
Change-Id: I09aeb76d614db57b1884ac7ee9f00c152cd77849
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4892
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The specific SWD API to change/query the adapter speed is never
called because the equivalent JTAG API is used in place of it.
In the restructure of struct jtag_interface, the JTAG API is
promoted as global adapter API, thus a specific SWD one is not
anymore required.
Change-Id: I1e810d255b4dfcd5791b4fac8ae1260c31a057fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4891
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently size of the GDB buffer is 16384 bytes but it is treated as
nul-terminated string in most of the code, so effective size of the
buffer is actually 16383 bytes. OpenOCD responds with `PacketSize=3fff`
to qSupported request. Result of GDB's `m` command is encoded in hex so
each data byte uses two bytes in the buffer. As a result GDB will split
bulk read requests into chunks 0x1fff bytes each. This causes troubles
on targets (or memory regions) which support only aligned, word-sized
access (such as MMIO buffers).
Steps to reproduce (psoc6 target):
gdb> dump binary memory dump.bin 0x040320000 (0x040320000 + 65536)
OpenOCD:
Error: Failed to read memory at 0x40321ffe
Error: Failed to read memory at 0x40321000
Error: Failed to read memory at 0x40323000
Error: Failed to read memory at 0x40325ffe
Error: Failed to read memory at 0x40329ffa
Error: Failed to read memory at 0x40329ffc
Error: Failed to read memory at 0x4032bffc
Error: Failed to read memory at 0x4032dffa
Consolidate GDB_BUFFER_SIZE usage: ensure size of each buffer is
(GDB_BUFFER_SIZE + 1), add explicit comment that additional byte is used
for nul-termination. Report correct size of the buffer to GDB (0x4000)
as recommended in GDB's docummentation: `if the stub stores packets in a
NUL-terminated format, it should allow an extra byte in its buffer for
the NUL`
Checked with clang-asan, clang-analyzer, valgrind - no new errors.
Change-Id: I909e8a2c6b010c5d4a304641808d4a807a4ec18d
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/5109
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The warning appears for every possible device during enumeration
and provides no useful information for an end-user.
Change-Id: I56e7889a5d9d4656de13ad9e21be3a6e1906e05f
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The implementation-defined bits have different semantics for each bus
and different recommended defaults.
Change-Id: I562fe24643bb1f3abc696339e382a75ccf2f2873
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a copy of handle_md_output() from src/target/dsp563xx.c
Change-Id: Iadd003fd1dcdbc7990d46a58ee2e7c30826ac6af
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5175
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
s/additonal/additional/
s/seperately/separately/
Use uppercase after a '.'
Change-Id: I933894ae44924363d634fa07d3de4ceeb4b329e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5162
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
By definition the EXTERNAL bit in Debug Fault Status Register indicates
that an external debug request (EDBGRQ) signal was asserted.
Usage example: this could be done by CTI in multicore devices in order to
halt all the cores together.
Change-Id: I7830455ce5da6702b7d08c8fa7bfe80e4d8a5055
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5157
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 89fa493a3b removes the top
level command "unknown" and adds in command_unknown() some unclear
code that should detect a user-implemented "unknown" command.
But, all the commands that trigger the execution of the function
command_unknown() are registered in register_command_handler() and
have the command name prefixed with "ocd_".
Due to such "ocd_" prefix in cmd_name, the condition
if (strcmp(cmd_name, "unknown") == 0) { ... }
is always false.
Nobody complained for almost 10 years so we can proceed to remove
this dead code, before merging any change that obsoletes the
prefix "ocd_" and potentially makes the condition true.
Remove the dead code guarded by the condition above.
Change-Id: Icf11a956bb2d68fc84e6eb5779edf8e35db8fa53
Fixes: 89fa493a3b ("remove unknown handler")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Left unused after commit "target: unify memory read/write
commands", can be removed.
Change-Id: Iea6ef9204c8071283a66a679b3d6edbb0c929c5c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5153
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The documentation added for commit b3d29cb544
was merged after the end of the eSi-RISC section rather than AARCH64.
This patch relocates this hunk to the correct location.
Change-Id: I46a2d24442556e9e8000b46a5e1af03b83de6d98
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/5181
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The V3M SoC is R8A77970 while the V3H SoC is R8A77980 . Update the
CHIPNAME and swap the SoCs to keep the list sorted.
Change-Id: I7e1777c0c7181e5e0beac98333f2047cb443d0df
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5140
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H target.
This is an SoC with one Cortex A9 ARMv7a core and
up to 10 MiB of on-SoC SRAM.
Change-Id: I20fd54b385fe1ba1cc325451c3fdfa3a835d4884
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H GR-Peach board,
which is a cheap development kit for the RZ/A1H SoC.
Change-Id: I7f5596ae47e6dff8e6d06cffd4dddca20f57d0ca
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In case of error, a command should use command_print() to report
the error message, so it get printed only on the session that run
the command itself, and the message can be intercepted with the
tcl command catch if it has to be handled differently.
Current code drops the command output when the command returns
error, claiming that it's the command that *should* have printed
it already. This is true only if we *abuse* of the LOG functions,
but accepting the side issue of having the LOG printed in every
session and being unable to catch{} the error message.
Since we have switched to command_print(), change the code to
propagate the command output also in case of error.
Change-Id: I95de424a65e63702bdb3b2277749a0ac6aaaa503
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5178
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Two calls to command_print() in imx_gpio fixed - the first parameter
adjusted (CMD_CTX -> CMD) per the changes from this commit:
6cb5ba6f11
Change-Id: I6cb0909439a632d3109edfc68070b9b561f86d49
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5176
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The commit 84ca4995ad ("drivers/bcm2835gpio: fix usage messages")
has been merged before commit 6cb5ba6f11 ("helper/command: change
prototype of command_print/command_print_sameline") introducing two
new call to command_print() that were not modified by the second
commit.
This triggers a compile error on ARM host.
Fix the incorrect function call.
Change-Id: I2736bae24141685b7590fd6b4aa5e6a29b2cab29
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5174
Tested-by: jenkins
Marc Schink
Omair Javaid
Antonio Borneo
Tarek BOCHKATI
Tilman Sauerbeck
Christopher Head
Tomas Vanek
Michael Schwingen
Daniel Goehring
Florian Fainelli
Andreas Fritiofson
Bohdan Tymkiv
Oleksij Rempel
Leonard Crestez
Steven Stallion
Marek Vasut
Jan Matyas