This commit is only for the sake of completeness as
default coreid is zero. In any case, coreids 1-4 are
used for the different PRU cores inside the SoC.
Change-Id: I775f2f444b1a908ffaf7bdbc43bcc966f19668c4
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2621
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use more descriptive names for JRC and DAPs
so they more closely match documentation.
For example there's no Cortex A9 DAP, that's
the DebugSS DAP where Cortex A9 target sits. In
that same DAP we have have ETM, STM and both
dual-PRU subsystems.
Change-Id: I0e66ebb6299763f96606fae3e4c62e5785c804f2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2620
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Main DAP (where Cortex A9 sits) ID is actually
0x46b6902f. Fix it.
Change-Id: Ifa3335186bcf60d264d4ecea477bfe2f5ca10ead
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2619
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
this event handler will configure and lock PLLs
and configure DDR so platform is placed in usable
state.
Change-Id: Idd02f4c9789181d69578f8606ac3576ea1dd8a0b
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2616
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
sometimes, watchdog might be left running and
it could expire in the middle of a debug session,
to prevent that, just make sure to disable watchdog
on reset-end if current state is 'halted'.
Change-Id: Ib4f2a2321cba17cd8c56ca3ae63114a563a6de90
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2615
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
a later commit will implement a proper reset-init
handler to lock pll and configure ddr as we should.
Change-Id: I432cf28a5a944bfa83c20aed7298dbd29df30e38
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2614
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
According to AM4379 TRM [1], table 2-1 L3 Memory Map,
we have a total of 256KiB and there's no reason not to
use it all.
[1] http://www.ti.com/lit/ug/spruhl7b/spruhl7b.pdf
Change-Id: I117f2afe721bc4e3f0df304d3542e1a91aa69d12
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2611
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since commit ec9ccaa288 (arm_adi_v5: make dap_lookup_cs_component()
traverse subtables and handle multicore) AM437x devices can't be used
with OpenOCD anymore. The reason is that dbgbase used to be set to zero
before that commit and that just happens to work with AM437x devices.
A more robust solution is to pass correct dbgbase when creating the
target, which this commit does.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change-Id: Iaf2617804324de8094b25137943e08b84f14c75f
Reviewed-on: http://openocd.zylin.com/2602
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This should allow most of the existing configurations for older
versions to remain compatible without forcing the user to change his
or her config to explicitly select transport.
Also in some circumstances can remove the need to chain a "-c transport
select X" when building custom configs on the command line, which seems
like a common new user pitfall.
Change-Id: Ic87a38c0b9b88e88fb6d106385efce2f39381d3d
Suggested-by: Petteri Aimonen <jpa@git.mail.kapsi.fi>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2551
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Valgrind-tested.
Comparison of flashing performance on an FRDM-KL25Z board running mbed
CMSIS-DAP variant, 5MHz clock, old driver:
wrote 28096 bytes from file demo.elf in 26.833590s (1.023 KiB/s)
verified 27264 bytes in 1.754972s (15.171 KiB/s)
this implementation:
wrote 28096 bytes from file demo.elf in 3.691939s (7.432 KiB/s)
verified 27264 bytes in 0.598987s (44.450 KiB/s)
Also tested "Keil ULINK-ME CMSIS-DAP" with an STM32F100 target, 5MHz
clock, results reading from flash, old driver:
dumped 131072 bytes in 98.445305s (1.300 KiB/s)
this implementation:
dumped 131072 bytes in 8.242686s (15.529 KiB/s)
Change-Id: Ic64d3124b1d6cd9dd1016445bb627c71e189ae95
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2356
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I984d2018f7d47a1042f1e12894563154fa7b566c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2196
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Initial Support for AT91SAM7A2 on Olimex SAM7-LA2 board.
The board seems not to be able to reset into halted mode, as srst is
connected to NRESET of the cpu (configured srst_pulls_trst).
JTAG RCLK is connected to CLK.
Tested with interface/ftdi/olimex-arm-usb-ocd-h.cfg.
Change-Id: I2bdd67e3683e45f1119c5850bad294aa107891d8
Signed-off-by: Arne Wichmann <arne.wichmann@gmail.com>
Reviewed-on: http://openocd.zylin.com/2318
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds configs for Alphascale asm9260t ARM based SoC and
Evaluation Kit based on this chip.
Change-Id: Id8d3a1ef204e3ae84540c2693e3d62650ba82f73
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2515
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The flash definition belongs in the target cfg. Add some working area
and suitable reset_config.
Make kx.cfg more similar to klx.cfg.
Disable rclk as it is dead slow and a fixed 1MHz clock seems to work.
Change-Id: I8328f179c3a33be64403da93616abb48651bdfe6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2227
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
Add configs for Atheros ar9331 MIPS based WiSoC and
board based on this chip: TP-LINK TL-MR3020
Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2519
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.
These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.
The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.
Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds support for Silicon Labs (formerly Ember) EM357
and EM358 chips and derivatives.
Change-Id: Ie63aed95a2f4ef1a6b955e301a51b4de1b3a5462
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2470
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds a trivial config for LPC8xx chips based on the already
existing infrastructure in lpc1xxx.cfg.
Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2464
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
It depends on the particular target whether it can work with SRST
asserted or not, so this belongs to the target config rather than the
board config.
Also, this allows for simple
openocd -f myboard.cfg -c "reset_config connect_assert_srst"
command to be used whenever a user feels a need to connect to an
unresponsive target.
Change-Id: I3d8da9ae47088fc0c75a20bfdd20074be1014de0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2459
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
So remove it from all the configs, it's misleading, and leads to cargo
culting of config files.
Change-Id: I2b77e60d5e96f9759c7c9fc91b20e73be2e95d9a
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should have been corrected earlier with the split of l1/l0 code
apart.
Change-Id: I87b94a310ae7e76318554a9cd2705348a942d58b
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2447
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
L0 is cortex m0+, so different id codes, SWD only, different addresses
for the clock speedup. It has no endian options, no boundary scan.
Removed all L0 specific portions from L1 files, and renamed files to clarify
their purpose. The deprecated stm32lx_stlink.cfg is kept as is, as it is only
around for backwards compatibility with prior releases.
Tested on STM32L053 Discovery and STM32L151 Discovery.
Has _not_ been tested with jtag on L1.
Change-Id: I8eea890d2f92a302d9e9c8a8832d218ee1b6bcfc
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Fix script parse error, when using JTAG, introduced in
commit 0187ced9ed
Add several BS TAPIDs with comments about ST documentation.
Change-Id: I8d0370b244ccaf7ea0dbe1919bfad1915f7317d4
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-on: http://openocd.zylin.com/2376
Tested-by: jenkins
Reviewed-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since all F4 parts have an internal HSI providing 16MHz, it's safe to
use 2MHz JTAG frequency by default.
Change-Id: I2702d5a1d642d4acd4af2db54c028949132c6900
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2383
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add CPUTAPID for stm32 L0xx mcu devices. Using -expected-id to
add the new id with the id for L1xx devices. This for reduce the
duplicated code.
Change-Id: I48bd230884ecf38fa200c620b547bdf3b5f59132
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2315
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since now auto-detection for flash size works nicely, there's no
reason to keep numerous configs around.
Change-Id: If0cbc37985abf17ef7c1f7d0688e76500fac228f
Signed-off-by: Vanya Sergeev <vsergeev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1960
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds config to allow JTAG debugging of an ARM core of a modern
hybrid SoC by Research Centre "Module"
(http://www.module.ru/en/company/). К1879ХБ1Я is targetted at set-top
boxes and other multimedia equipment, the official SDK is Linux-based.
Change-Id: Ib2ae5784d25699f952682e66b025a3f677a76d5d
Signed-off-by: Бурага Александр <dtp-avb@yandex.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2272
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is for mx6q TO1.1.
Change-Id: Id6af2ed232fc19be9bf49eb6d2df0004c6668698
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2253
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to Nordic Semiconductor Product Anomaly Notice (document
NRF51822-PAN), item 16, some revisions of nRF51822 sometimes reset
without all RAM blocks enabled. This was noted on NRF51822-QFAA rev
CA/C0, only 8KiB of memory was accessible.
This patch turns on all RAM following a debugger induced reset
(matches specified behaviour.)
Change-Id: I4f8be4ec3d1271da7fe5bc9a084fdcb2968535bb
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2202
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Felipe Balbi
Angus Gratton
Paul Fertser
Uwe Bonnes
Andreas Fritiofson
Nemui Trinomius
Arne Wichmann
Oleksij Rempel
Andreas Bomholtz
Pawel Si
Jacob Palsson
Ed Beroset
Tomas Vanek
Karl Palsson
Karl Palsson
Juha Niskanen
Spencer Oliver
Rémi PRUD'HOMME
Vanya Sergeev
Бурага Александр
Andrey Skvortsov