By default pic32mx starts after any reset with 1 wait state for RAM access/exec.
It can be changed to 0 wait states by clearing the BMXWSDRM bit (bit 6) in BMXCON register.
With 0 wait states near doubles the execution speed. CRC check sum can be done much faster
increasing verify_image speed. Fast data transfer also works with a bit higher scan rate, up to 1500 Khz.
This option can be set at any time with
mww 0xbf882004 0x40
or cleared with
mww 0xbf882008 0x40.
Some numbers for FTDI/HS with current devel code and a elf file:
Core clock / wait states verify_image speed
------------------------------------|------------------------------
4 Mhz / 1 21 KiB/s
4 Mhz / 0 36 KiB/s
8 Mhz / 1 37 KiB/s
8 Mhz / 0 57 KiB/s
Change-Id: I4092ad0f3753f72f77108718d0ed3a3ab84e3b23
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1141
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
To show up the fail try to step with the core clock set to 31.25Khz
and with a ftdi/hs adapter or with a wiggler, -not with ft2232-.
The scan frequency should be set to 300Khz or higher, at lower frequency probably will not fail.
The code exits with error because the pracc address is at 0x0.
It also fails when using the "all" register, but in this case the code works without any message because the
pracc address is at 0xff202004 when it fails.
I never saw this fail with the core clock set to 500Khz or higher, but ...
The workaround simply puts a 1 ms delay after the execution of the DERET instruction.
Change-Id: I38e8c01a9c39aedd3282140543b83a0844d8ad29
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1139
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for ARMv7-M targets in arm_nandwrite and
arm_nandread.
Change-Id: Iab1d78d401f735e191c6a8519f3619035a300fae
Signed-off-by: Henrik Nilsson <henrik.nilsson@bytequest.se>
Reviewed-on: http://openocd.zylin.com/1188
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Fixes system hang for devices that don't ignore
transactions to bad addresses.
Change-Id: Ia98344d7efc12951ef79dbc82b8f792b70a22cee
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/1115
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Moved JTAG code out of transport-neutral file (arm_adi_v5.c) into
transport specific file (adi_v5_jtag.c).
Added ap_block_read to dap_ops interface (arm_adi_v5.h) to support
the move.
Change-Id: I796d3984f138aad052b97c77ac9c12ffd1158f74
Signed-off-by: mike brown <mike@theshedworks.org.uk>
Reviewed-on: http://openocd.zylin.com/1277
Tested-by: jenkins
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These were missed when git was moved to the new SF platform during Nov 2012.
Change-Id: I7b4ae9dea010d95f9bf4c26841b5b724f41768be
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1248
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
makeinfo has a long outstanding bug that means @anchors are not correctly
formatted for split html, see:
http://lists.gnu.org/archive/html/bug-texinfo/2012-06/msg00000.html
The issue relates to using spaces or hyphens in the @anchor name.
Issue also reported via Trac #44
Change-Id: Id72e23375dd167674b2ae5b314e8242b90a72a5f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1244
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The command 'at91sam3 info' ignores PLLA DIV values >1. This patch fixes it.
Tested on a SAM3S4C chip.
Change-Id: I051f41bb3dcefe1ac785fbcb48477a807daa16a2
Signed-off-by: Thomas Schmid <thomas.schmid@gmail.com>
Reviewed-on: http://openocd.zylin.com/1307
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The commit "gdbserver: use common hexify/unhexify routines" [3d62c3d]
mis-replaced a call to "str_to_hex" with a call to "unhexify". "hexify"
should have been used instead.
Change-Id: I5f5904b1b422f819a6308e2c0740ea43d22c7d0b
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/1308
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This regression was caused due to the recent addition of R4 support and
the removal of the bulk_write_memory handler.
Change-Id: Ide692737f235c0e9906becb6f3502ba52c5907aa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1246
Tested-by: jenkins
The only caller was arm_nandwrite(). Replace that call with
target_write_buffer() instead, which in turn may end up calling the same
bulk_write_memory target API function.
Change-Id: If34c7474df5cf14af3b732fb4774816818f28e79
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1214
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove dummy implementations from all targets except arm7_9 and mips, which
are the only ones with real implementations. Replace with a single default
implementation simply calling target_write_memory().
Change-Id: I9228104240bc0b50661be20bc7909713ccda2164
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1213
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for usbprog-jtag and usbvlab that are mostly compatible
to opendous except for IN and OUT endpoints and usb transfer mode.
Change-Id: I44557c2449fe7473295038efa6ae4fc8d80ec7bf
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/687
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
usb_blaster_device_desc was allocated, but never freed.
Change-Id: I764bd092c71b8c260b98aab0e7a1710fd7bfa9fd
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1224
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
If command parport_cable is not executed, parport_cable points to
const char array in read-only memory as default. On exit free()
will try to free this read-only memory. This patch uses strdup to
allocate memory when defining default setting.
Change-Id: I290e707ac6a37e9dc1b45c85ca51d8bd6aac6761
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1223
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Appending bits to TAP buffer doesn't check if there's enough space left.
This patch adds this check to fix TAP overflow error.
Change-Id: If80d5ab4a24983ad24f3cab31f9676d1590ebf5d
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1216
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It was listed in the ft2232 based cables supported. Moreover, the
ft2232_channel option, which was added to support this cable, was explained.
Change-Id: I82ebc7bc10d6472f96ab150e78d623a617edccd2
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config file add support to the opendous cable based on the chip ft2232H,
using the ft2232 interface driver.
Change-Id: I8171a0c475af8d61e081844ee86466a392138fb0
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1096
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
With this option a different channel of the ft2232 chip can be selected using
a previously existing layout. It was made for a partner called Salvador
Tropea.
Change-Id: Ia0dedb2f50e232d089e73788735edc8f47ee23e6
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1095
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The kinetis datasheets specify the flash registers as bytes rather
than as words, as the previous implementation did. This also makes
a few code sections slightly less endian-magical.
Change-Id: If8f4adfc7f4341085ae5b6eacbf7d74bbd74cf08
Signed-off-by: Alex Austin <alex.austin@spectrumdsi.com>
Reviewed-on: http://openocd.zylin.com/1192
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add url to show where the http password is configured.
Also add note that password can also be saved to url git config.
Change-Id: I3c1a022580e5f73372b0c50e8d1d2f0b1498966f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1207
Tested-by: jenkins
This adds a program proc that simplifies using OpenOCD as a standalone
programmer.
Change-Id: I6ece492cd878c170b734e8bb2e09fe8c4557d5a6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1199
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This reduces the number of gdb conversion routines we have to maintain.
Change-Id: Ia43d6cac86cbe4f76fe0875b9d9c16ac340296db
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1128
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This config file add support to the opendous cable based on the chip ft2232H,
using the ftdi interface driver.
Change-Id: I4491f99d7b14f7078a04583ef0c4acd8692c4349
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rather than use bold fonts etc, use the correct keywords so doxygen formats
better.
Change-Id: Id9d63f0fc3465665376d7a536c4d6da71998f40e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1210
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes an issue if the device is manually probed after the initial probe
fails due to being unable to read flash size register. In this situation the
driver assumes the user has overridden the flash size when infact this may
not be the case.
It also seems on the older stm32f1 devices the flash register is not readable
when locked, this does not seem to apply to the newer parts - f0, f3, f4.
Change-Id: I125f872fcb2d962ca6705f97b62d957e2b31303b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1187
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stm32f0 and stm32f3 share the same option byte location, but the format
differs.
Adding an option_offset fixes the broken options_read cmd and incorrectly
setting Hardware Watchdog when unlocking a f3x device.
Change-Id: I82d66b6198294ea9eedb44ca8b2fb368c0cb15e8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1184
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This change adds a simple target configuration for Freescale
single/dual/quad core i.MX6 SoCs, only one core is configured by default.
Change-Id: I853dd27f4c6765b7f731be2ddea82e85d496c6a4
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-on: http://openocd.zylin.com/1135
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When the ftdi driver calls finally the mpsse_flush function, it first
initiate the USB in and finally the corresponding USB out transaction.
Because data in is requested too early the USB device will always answer
the first USB in by a NAK. That can prevented by a simple reordering of
the out and then the in transfer and can improve the Jtag performance for
high JTAG clock rates.
Change-Id: I17abf1487c914c92e2e447ee6d30562ef629f327
Signed-off-by: Peter Henn <Peter.Henn@web.de>
Reviewed-on: http://openocd.zylin.com/942
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This patch change the default reset config from SYSRESETREQ to the working
VECTRESET.
Change-Id: I21a9a74b9c0c68cfa3a6e6dac9b123acc98a93cb
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1186
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move the global target back off timer to the target struct. This will
fix the wrong error handling with multi target devices like smp systems.
Change-Id: Ia327182ed5d13ca87323700017a8c40ecc6b25a3
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1179
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Inform about possibility of discarding negative review in Gerrit when specific conditions are met.
Change-Id: I432b6c93cefc368fa22ce1096bea4cd174e03816
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/747
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
The USB buffer will need space for both TMS and TDI buffers.
Each holds tap_buffer_size bytes maximum, so tap_buffer_size must be
smaller than half of usb buf_size.
Change-Id: Id8f39936a894cbd98deb89eec5a859aef1e2b783
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/1136
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Salvador Arroyo
Henrik Nilsson
Evan Hunter
mike brown
Spencer Oliver
Thomas Schmid
Christian Gudrian
Andreas Fritiofson
Stefan Mahr
Rodrigo Melo
Drasko DRASKOVIC
Alex Austin
Øyvind Harboe
Vladimir Zapolskiy
Peter Henn
Mathias K
Freddie Chopin
Joerg Fischer