cortex_a_read_apb_ab_memory_fast() uses the wrong order of ITR and DSCR
writes when setting up the transfer. ARM DDI0406C says in C8.2 regarding
"Fast mode" operation to first switch to fast mode and then latch the
instruction in ITR. Current implementation first wrote ITR, causing
the instruction to be executed immediately, then switched to fast mode
without an instruction latched. Repeated reading of DTRTX didn't
execute LDC and thus replicated its current content into the whole buffer.
This patch uses the following, revised algorithm:
1) switch to non-blocking mode and issue the LDC for the first word
2) if more than one word is to be read:
- switch to fast mode
- latch the LDC instruction into ITR (it is _not_ executed)
- issue (count-1) reads of DTRTX register, each read returns the current
content of DTRTX and re-issues the latched instruction
-> now the second-to-last word is in the buffer and the LDC for the last
word has been issued.
3) wait for the last instruction to complete
4) switch back to non-blocking mode
5) Read DTRTX for the last (or: only) word and put it into the buffer
Change-Id: I44f5c585962ffa5af257c3d5a2a802c122b6b1e4
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3122
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When accessing memory through the ARM core, privilege levels and mmu
access permissions observed. Thus it depends on the current mode of the
ARM core whether an access is possible or not. the ARM in USR mode can
not access memory mapped to a higher privilege level. This means, if the
ARM core is halted while executing at PL0, the debugger would be
prevented from setting a breakpoint at an address with a higher privilege
level, e.g. in the OS kernel. This is not desirable.
cortex_a_check_address() tried to work around this by predicting if an
access would fail and switched the ARM core to SVC mode. However, the
prediction was based on hardcoded address ranges and only worked for
Linux and a 3G/1G user/kernel space split.
This patch changes the policy to always switch to SVC mode for memory
accesses. It introduces two functions cortex_a_prep_memaccess() and
cortex_a_post_memaccess() which bracket memory reads and writes. These
function encapsulate all actions necessary for preparation and cleanup.
Change-Id: I4ccdb5fd17eadeb2b66ae28caaf0ccd2d014eaa9
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3119
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
when disabling the mmu to access physical addresses, normally the d-cache
must be disabled as well. Disabling the d-cache also requires a full
clean&invalidate. However, since all memory writes are treated as write-
through no-allocate and memory reads do not allocate cache lines,
effectively the d-cache state does not change at all. We can therefore
save the the d-cache disabling and flushing.
This patch also simplifies the function a bit.
Change-Id: Ia17c56a28f432156429cd4596107e3652b788e63
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3114
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
for minimal impact on the hardware state, force all memory accesses to
bypass the caches and tlbs. This may actually be the default, but ARM
recommends in DDI0406C to set proper default values on debug init.
Change-Id: If5ac097b6ee725c047b1e86c2f90eabe16b98c7b
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3079
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Other cache functions use an updated pattern for the address range loop.
Bring dcache clean and flush functions in line.
Change-Id: Iccb4a05c49054471033a3403363110cb08245d5b
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3035
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Call armv7a_l1_d_cache_flush_virt() before writing the breakpoint,
to make sure the d-cache is clean and invalid at the breakpoint
location down to PoC.
Call armv7a_l1_d_cache_inval_virt() after writing the breakpoint
again, so that d-cache will pick up the modified code.
Call armv7a_l1_i_cache_inval_virt() after writing the breakpoint
to memory to make the change visible to the CPU.
Change-Id: I24fc27058d99cb00d7f6002ccb623cab66b0d234
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3033
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
D-Cache invalidate is a dangerous operation. It will only work correctly
if full cache lines are invalidated. When partial cache lines are
invalidated, i.e. the target address range does not start and end
at a cache line boundary, cpu data writes outside of the target range
will be dropped. This patch adds special treatment for partial cache
lines by doing a clean & invalidate on the partial lines before
invalidating the rest of the range.
Change-Id: I64099ddb058638e990a7eb0ee911b9cc8f6f8901
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The following changes are implemented:
- Clean&Invalidate the VA range to PoC *before* the write takes place
- Remove SMP handling since DCCIMVA instruction already maintains SMP
coherence.
- Remove separate Invalidate step
Change-Id: I19fd3cc226d8ecf2937276fc63258b6a26e369a7
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3027
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This patch adds a function for cleaning & invalidating a virtual
address range from the architecture caches down to the point of
coherence.
Change-Id: I4061ab023a3797fabc967f3a34498034841d52c6
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3026
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
There's only one function left that handles cache info display,
no need any more for a function pointer and runtime initialization.
Change-Id: I90b09577f81607917b11f0ab5600a0e2dce223e2
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3025
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
ARMv7 architecture allows up to 7 cache levels that are architecturally
visible, as opposed to "system caches", which are outside of the domain
defined by ARMv7 and require separate management. This patch enables
detection and identification of caches at all levels. It also implements
a new "flush-all" function that cleans & invalidates all cache levels to
the "Point of Coherence".
Change-Id: Ib77115d6044d39845907941c6f031e208f6e0aa5
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3024
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This patch is on the path to unified handlers for both inner and
outer caches. It removes the special overrides installed when
an outer cache is configured.
Change-Id: I747f2762c6c8c76c700341cbf6cf500ff2a51476
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3022
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The outer cache is not necessarily at L2 in a system. Rename functions
to make that clear.
Change-Id: Ia636a4844f50634f2bdf5cdce285febc1a47c11f
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3020
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch introduces, new command set and handlers for l1 and l2x caches.
Patch set 10 folded the following changes into this one:
Ib1a2a1fc1b929dc49532ac13a78e8eb796ab4415
If8d87a03281d0f4ad402909998e7834eb4837e79
I0749f129fa74e04f4e9c20d143a744f09ef750d8
Change-Id: I849f4d1f20610087885eeddefa81d976f77cf199
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/2800
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This was needed for ahb access
Change-Id: I638f45a276a593c08140b5d9d7480617aa85f096
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2796
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Problem
dap->ap_current is register value, not field value.
it restores invalid ap when it calls dap_ap_select(dap, ap_old) later.
* assume the current ap is 1, dap->ap_current value would be (1 << 24).
ap_old = dap->ap_current; <-- ap_old = 1<<24 = 0x1000000.
...
dap_ap_select(dap, ap_old); <-- select 0x1000000, not 1.
* All AP registers accessing fail afterwards.
One of the reproducible case(s): CORE residents in AP >= 1
dap_lookup_cs_component() being used to find PE(*).
In most cases, PE would be found in AP==0, hence the problem is hidden.
When AP number is 1, dap->ap_current would have the value of 1<<24.
Anyone get the AP value with dap->ap_current and resotre it later would
select the wrong AP and all accessing later would fail.
The ARM Versatile and/or FPGA would have better chance to provide this
kind of environment that PE residents in AP>=1. As they have an 'umbrella'
system at AP0, and main system at AP>=1.
* PE: Processing Element. AKA Core. See ARM Glossary at
http://infocenter.arm.com/help/topic/com.arm.doc.aeg0014g/ABCDEFGH.html
Fix
Use dap_ap_get_select() to get ap value.
a. Retrieve current ap value by calling dap_ap_get_select();
src/flash/nor/kinetis.c
src/target/arm_adi_v5.c
b. The code is correct (dap->ap_current >> 24), but it's better to use
dap_ap_get_select() so everything could be synchronized.
src/flash/nor/sim3x.c
Change-Id: I97b5a13a3fc5506cf287e299c6c35699374de74f
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2935
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If supported, the maximum transport speed is now retrieved from the
device.
Change-Id: I614f405ec91cf199c851781785fd26cbd10c37a6
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2955
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch uses libjaylink which is a library to access J-Link
devices. As other tools which are not in the scope of OpenOCD also
need to access J-Link devices a library is used. A firmware upgrade
tool and an advanced configuration tool for J-Link devices are under
development.
Further versions of libjaylink will support additional features
OpenOCD could benefit from. This includes TCP/IP as additional
possibility to connect to J-Link devices as well as power tracing and
device internal communication. The latter is used to access
peripherals on some development boards (e.g EFM32 STK and DVK).
Integration of libjaylink is realized with a git submodule like
jimtcl. As libjaylink depends on libusb-1.0 only, no additional
dependency is introduced for OpenOCD.
All low-level JTAG and SWD implementations of the current driver are
left untouched and therefore no incompabilities are to be expected.
Improvements of this patch:
* Support for more USB Product IDs, including those with the new
scheme (0x10xx). The corresponding udev rules are also updated.
* Device selection with serial number and USB address.
* Adaptive clocking is now correctly implemented and only usable for
devices with the corresponding capability.
* The target power supply can now be switched without the need for
changing configuration and power cycling the device.
* Device configuration is more restrictive and only allowed if the
required capabilities are available.
* Device configuration now shows the changes between the current
configuration of the device and the values that will be applied.
* Device configuration is verified after it is written to the device
exactly as the vendor software does.
* Connection registration is now handled properly and checks if the
maximum number of connections on a device is reached. This is also
necessary for devices which are attached via USB to OpenOCD as
some device models also support connections on TCP/IP.
* Serial Wire Output (SWO) can now be captured. This feature is not
documented by SEGGER however it is completely supported by
libjaylink.
This patch and libjaylink were tested on Ubuntu 14.04 (i386),
Debian 7 (amd64), FreeBSD 10.0 (amd64) and Windows XP SP3 (32-bit)
with the following device and target configurations:
* JTAG: J-Link v8.0, v9.0 and v9.3 with AT91SAM7S256
* SWD: SiLabs EFM32 STK 3700 (EFM32GG990F1024)
* SWD: J-Link v8.0, v9.0 and v9.3 with EFM32GG990F1024
* SWD: XMC 2Go (XMC1100)
* SWD: XMC1100 Boot Kit (XMC1100)
* SWD: IAR Systems / Olimex Eval Board (LPC1343F)
* SWD: Nordic Semiconductor nRF51 Dongle (nRF51422)
* SWD: SiLabs EZR32 WSTK 6220A (EZR32WG330FG60G)
Except for Windows XP all builds are tested with Clang in addition to
GCC. This patch and libjaylink are not tested on OSX yet.
Change-Id: I8476c57d37c6091c4b892b183da682c548ca1786
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2598
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
http://support.code-red-tech.com/CodeRedWiki/DebugAccessChip
> Note that once you have recovered debug access to your MCU, then in most cases you should then modify your Debug Configuration to turn vector catch off again. If this is not done, then this can cause problems in some circumstances with some versions of the Code Red IDE. For example with NXP LPC13xx parts, connecting more than once to the MCU with vector catch enabled can lead to the part ID being incorrectly read - which can again cause debug connections to fail
This patch adds an alternative part ID for LPC1343. With this patch "program" command works fine for flashing.
Change-Id: I8632e898a4c33102455925d25715b4f4edfa1d97
Signed-off-by: Jakub Kubiak <jakub@kubiak.es>
Reviewed-on: http://openocd.zylin.com/2782
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This adds docs, example config, flash driver.
Driver is only supports K1921VK01T model for now.
Change-Id: I135259bb055dd2df1a17de99f066e2b24eae1b0f
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Reviewed-on: http://openocd.zylin.com/3011
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The probe and info methods had duplicate sections decoding family names
to generate a human friendly part name. Extract this to a common
helper.
Change-Id: I4c6309d83c601e154b7c14ad9c15c53854ee1e98
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2932
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Basic basic support to get running, magic numbers taken from revision
0.90 of the reference manual.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Change-Id: Iff6ab94d30698f056ef09f7a856b7285fed8f441
Reviewed-on: http://openocd.zylin.com/2931
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By saving a pointer to the tail of the list,
we don't need to traverse the entire command
queue before we're able to append an item to
it.
With this patch, I see a 10% improvement when
using the embedded XDS100v2 on AM437x IDK board
to load a 4MiB binary (linux zImage) to DDR
with load_image.
IOW, we went from ~305kB/sec to ~336kb/sec.
Change-Id: Idb55d49f0d0106043374ab520b2f3b6b32f2c50f
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2709
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Daniele Emancipato <daniele12457@hotmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The svf_progress_enabled variable is global, hence its lifetime is not
limited and it retains the value from the previous run. Fix this by
explicit assignment.
Change-Id: Id6f4fa88f39521606342a37f6876a0948ac5406e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3111
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This makes SVF error output match actual line numbers in the file
processed.
Change-Id: I1fa4b9d0891e4358b7beada516945d5331ebe182
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2945
Tested-by: jenkins
Kinetis driver checks MDM STAT register to detect secured state of MCU.
An unsecured clean device typically triggered a huge fat alarm message.
Now when driver detects secured state it tries to halt MCU and then
re-reads status register.
Command "mdm mass_erase" used to deassert reset when finished
and MCU started looping in hard fault - WDOG reset cycle.
Now "reset halt" is issued. Clean flash is not run after mass_erase.
Change-Id: I23f393509fbd8751d44ffc744ff2d67f1074f74e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3010
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Base config without flash support for now.
Change-Id: I96a5b6ad35e00dc706177ea9dbdffc384ae7f62b
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3110
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The pflash.0 bank should not be present as it overlaps with
the flash bank created by target/kx.cfg, triggering an error.
This is also in line with the existing twr-k60f120m.cfg.
Change-Id: I5f620e01319d967f12e029fb6865ccdd031713b3
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3108
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
SAMD driver suffered from following problems:
1) Flash was erased as an integral part of flash write.
It was not documented so with usual workflow it resulted
in erasing flash twice (and reducing flash lifespan)
and in almost double flashing time.
2) Sector erase was silently skipped if "is_erased" flag was set.
"is_erased" logic was not reliable, e.g. when a row write
was aborted after successful write of some pages, sector was
still considered as erased. "is_erased" flag could not
cope with flash writes from a user program.
3) Writing of a block with start address unaligned to a flash page
resulted in failed assert and OpenOCD abort.
4) Disabling cache in bit 18 of 16-bit halfword never worked.
MCU implements cache invalidate in hardware so there is no need
to take care about. This bug was reported by Tony DiCola.
New code does not erase flash in write operation.
Instead it traditionally relies on erasing flash beforehand.
"is_erased" logic and cache disabling is completely removed.
It simplifies write procedure a lot and flash write is now faster.
The change partly solves ticket #109 SAMD/SAM4L driver doubles flash erase.
Change-Id: I582b497d01a351575533a1f8c9810a4413be0216
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3045
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds support for the Atmel SAML21 variant B parts.
There is minimal change between the two variants, but in
variant B the automatic page write which the at91samd flash
driver relies on to be enabled is disabled by default.
With this patch the write row function will now issue a page write
command after each of the four pages in the row if the MANW (manual
write) bit is set. This also fixes flash write for the SAMC20/SAMC21
devices which have the MANW bit set by default as well.
I have also moved the device ID (DID) register bitfield extraction
from the find_part into helper macros. These can be used in the future
if there are more workarounds for specific devices.
Tested (programming) on:
ATSAML21-XPRO
ATSAML21-XPRO-B
SAMC21 Xplained Pro
SAMD21 Xplained Pro
SAMD20 Xplained Pro
Change-Id: I401a8aa1efd64730840c0d62cf49a1e880ea5900
Signed-off-by: Andreas Loehre <alohre@gmail.com>
Reviewed-on: http://openocd.zylin.com/2903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cmsis-dap protocol has both DAP_Connect and DAP_Disconnect commands.
Logically if cmsis_dap_swd_switch_seq() calls DAP_Connect in connected
state it should call DAP_Disconnect first.
Doing so surprisingly solves problems on Atmel EDBG with target SAMD/R/L/C.
Without this change SWD communication breaks after reset run/halt
in config "reset_config srst_only" and reconnect trials repeatedly
fail with "SWD ack not OK: 0 JUNK"
Change-Id: Ie951098d5e0c83f388e2df414608aaabec2135c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
16000kHz is only safe after PLLs have been locked
properly. Until that's done (with reset init), we
can only safely run at 1000kHz.
Change-Id: I4e0a17e88aa9919cd6c34d44da68e23115c0d3a3
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/3015
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added interface config file for the FTDI FT232H based UM232H module.
This should work with UM232H-B too, an even cheaper module, but
that has not been tested.
Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251
Signed-off-by: Ragnar Sundblad <raggesu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3031
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I232d769d893d54e4ea9411c46c56b19587b69919
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2707
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
According to Infineon, XMC4500 EES AA13 with date codes before GE212 -
as seen on an XMC4500 General App Kit - had a zero SCU_IDCHIP register.
Handle this by extending our checks to not error out on zero SCU_IDCHIP
and by printing a useful info string in that case.
Change-Id: Ic2d641a314627dd5a1ff775a0113999191b95e3d
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2751
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Matthias Welwarsky
Paul Fertser
Oleksij Rempel
Alamy Liu
Marc Schink
Jakub Kubiak
Bogdan Kolbov
Karl Palsson
Felipe Balbi
Tomas Vanek
Andreas Färber
Jonathan Larmour
Andreas Loehre
Ragnar Sundblad
Uwe Bonnes
Rémi PRUD’HOMME
Jeff Ciesielski
Morgan Quigley