tcl: add bcm47xx config and Asus RT-N16 board using it

This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".

The RAM setup is not done as it would require considerable efforts
without much practical gain.

The only issue I noticed so far is that "reset" doesn't actually reset
the chip.

Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.

Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.

Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
__archive__
Paul Fertser 2013-12-30 22:26:36 +04:00 committed by Spencer Oliver
parent 436f66b463
commit faedb14772
3 changed files with 41 additions and 0 deletions

15
tcl/board/asus-rt-n16.cfg Normal file
View File

@ -0,0 +1,15 @@
#
# http://wikidevi.com/wiki/ASUS_RT-N16
#
set partition_list {
CFE { Bootloader 0xbc000000 0x00040000 }
firmware { "Kernel+rootfs" 0xbc040000 0x01fa0000 }
nvram { "Config space" 0xbdfe0000 0x00020000 }
}
source [find target/bcm4718.cfg]
# External 32MB NOR Flash (Macronix MX29GL256EHTI2I-90Q)
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME cfi 0xbc000000 0x02000000 1 1 $_TARGETNAME x16_as_x8

5
tcl/target/bcm4718.cfg Normal file
View File

@ -0,0 +1,5 @@
set _CHIPNAME bcm4718
set _LVTAPID 0x1471617f
set _CPUID 0x0008c17f
source [find target/bcm47xx.cfg]

21
tcl/target/bcm47xx.cfg Normal file
View File

@ -0,0 +1,21 @@
echo "Forcing reset_config to none to prevent OpenOCD from pulling SRST after the switch from LV is already performed"
reset_config none
jtag newtap $_CHIPNAME-lv tap -irlen 32 -ircapture 0x1 -irmask 0x1f -expected-id $_LVTAPID -expected-id $_CPUID
jtag configure $_CHIPNAME-lv.tap -event setup "jtag tapenable $_CHIPNAME.cpu"
jtag configure $_CHIPNAME-lv.tap -event tap-disable {}
jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUID -disable
jtag configure $_CHIPNAME.cpu -event tap-enable "switch_lv_to_ejtag"
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME mips_m4k -endian little -chain-position $_TARGETNAME
proc switch_lv_to_ejtag {} {
global _CHIPNAME
poll 0
irscan $_CHIPNAME-lv.tap 0x143ff3a
drscan $_CHIPNAME-lv.tap 32 1
jtag tapdisable $_CHIPNAME-lv.tap
poll 1
}