tcl/target: add CC2538 and CC26xx target files (with cJTAG procedure)

Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.

These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.

The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.

Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
__archive__
Jacob Palsson 2014-07-29 14:36:40 +02:00 committed by Paul Fertser
parent 18d6c0b02b
commit 45a86f8e2a
3 changed files with 91 additions and 0 deletions

16
tcl/target/cc2538.cfg Executable file
View File

@ -0,0 +1,16 @@
# Config for Texas Instruments low power RF SoC CC2538
# http://www.ti.com/lit/pdf/swru319
if { [info exists CHIPNAME] } {
set CHIPNAME $CHIPNAME
} else {
set CHIPNAME cc2538
}
if { [info exists JRC_TAPID] } {
set JRC_TAPID $JRC_TAPID
} else {
set JRC_TAPID 0x8B96402F
}
source [find target/cc26xx.cfg]

43
tcl/target/cc26xx.cfg Executable file
View File

@ -0,0 +1,43 @@
# Config for Texas Instruments low power SoC CC26xx family
adapter_khz 100
source [find target/icepick.cfg]
source [find target/ti-cjtag.cfg]
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
set _CHIPNAME cc26xx
}
#
# Main DAP
#
if { [info exists DAP_TAPID] } {
set _DAP_TAPID $DAP_TAPID
} else {
set _DAP_TAPID 0x4BA00477
}
jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_DAP_TAPID -disable
jtag configure $_CHIPNAME.dap -event tap-enable "icepick_c_tapenable $_CHIPNAME.jrc 0"
#
# ICEpick-C (JTAG route controller)
#
if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x1B99A02F
}
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID -ignore-version
# A start sequence is needed to change from cJTAG (Compact JTAG) to
# 4-pin JTAG before talking via JTAG commands
jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap"
jtag configure $_CHIPNAME.jrc -event post-reset "ti_cjtag_to_4pin_jtag $_CHIPNAME.jrc"
#
# Cortex M3 target
#
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -chain-position $_CHIPNAME.dap

32
tcl/target/ti-cjtag.cfg Executable file
View File

@ -0,0 +1,32 @@
# A start sequence to change from cJTAG to 4-pin JTAG
# This is needed for CC2538 and CC26xx to be able to communicate through JTAG
# Read section 6.3 in http://www.ti.com/lit/pdf/swru319 for more information.
proc ti_cjtag_to_4pin_jtag {jrc} {
# Bypass
irscan $jrc 0x3f -endstate RUN/IDLE
# Two zero bit scans and a one bit drshift
pathmove RUN/IDLE DRSELECT DRCAPTURE DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRUPDATE RUN/IDLE
pathmove RUN/IDLE DRSELECT DRCAPTURE DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRUPDATE RUN/IDLE
pathmove RUN/IDLE DRSELECT DRCAPTURE DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRSHIFT DREXIT1 DRUPDATE RUN/IDLE
pathmove RUN/IDLE DRSELECT DRCAPTURE DREXIT1 DRPAUSE
# A two bit drhift and a 9 bit drshift
pathmove DRPAUSE DREXIT2 DRSHIFT DRSHIFT DREXIT1 DRUPDATE RUN/IDLE
pathmove RUN/IDLE DRSELECT DRCAPTURE DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRSHIFT DRSHIFT DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRSHIFT DRSHIFT DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRSHIFT DRSHIFT DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRSHIFT DRSHIFT DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRSHIFT DREXIT1 DRPAUSE
pathmove DRPAUSE DREXIT2 DRUPDATE RUN/IDLE
pathmove RUN/IDLE DRSELECT DRCAPTURE DREXIT1 DRPAUSE
# Bypass
irscan $jrc 0x3f -endstate RUN/IDLE
# Set ICEPick IDCODE in data register
irscan $jrc 0x04 -endstate RUN/IDLE
}