doc: remove references to "ocd_" prefixed commands

The commands prefixed with "ocd_" are removed.
Remove any reference in the documentation.

Change-Id: I27cebaa4752752ec8700757bf1c98b267c24f15b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5088
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
bscan_optimization
Antonio Borneo 2019-03-28 12:14:56 +01:00 committed by Tomas Vanek
parent 9eea9cce3f
commit 24bfdf53fd
1 changed files with 6 additions and 14 deletions

View File

@ -4926,7 +4926,6 @@ Use it in board specific configuration files, not interactively.
@end quotation
@end deffn
@comment the REAL name for this command is "ocd_flash_banks"
@comment less confusing would be: "flash list" (like "nand list")
@deffn Command {flash banks}
Prints a one-line summary of each device that was
@ -9534,13 +9533,12 @@ The following commands can be used to authenticate to a RISC-V system. Eg. a
trivial challenge-response protocol could be implemented as follows in a
configuration file, immediately following @command{init}:
@example
set challenge [ocd_riscv authdata_read]
set challenge [riscv authdata_read]
riscv authdata_write [expr $challenge + 1]
@end example
@deffn Command {riscv authdata_read}
Return the 32-bit value read from authdata. Note that to get read value back in
a TCL script, it needs to be invoked as @command{ocd_riscv authdata_read}.
Return the 32-bit value read from authdata.
@end deffn
@deffn Command {riscv authdata_write} value
@ -9553,9 +9551,7 @@ The following commands allow direct access to the Debug Module Interface, which
can be used to interact with custom debug features.
@deffn Command {riscv dmi_read}
Perform a 32-bit DMI read at address, returning the value. Note that to get
read value back in a TCL script, it needs to be invoked as @command{ocd_riscv
dmi_read}.
Perform a 32-bit DMI read at address, returning the value.
@end deffn
@deffn Command {riscv dmi_write} address value
@ -10439,10 +10435,6 @@ should be passed in to the proc in question.
By "low-level," we mean commands that a human would typically not
invoke directly.
Some low-level commands need to be prefixed with "ocd_"; e.g.
@command{ocd_flash_banks}
is the low-level API upon which @command{flash banks} is implemented.
@itemize @bullet
@item @b{mem2array} <@var{varname}> <@var{width}> <@var{addr}> <@var{nelems}>
@ -10450,7 +10442,7 @@ Read memory and return as a Tcl array for script processing
@item @b{array2mem} <@var{varname}> <@var{width}> <@var{addr}> <@var{nelems}>
Convert a Tcl array to memory locations and write the values
@item @b{ocd_flash_banks} <@var{driver}> <@var{base}> <@var{size}> <@var{chip_width}> <@var{bus_width}> <@var{target}> [@option{driver options} ...]
@item @b{flash banks} <@var{driver}> <@var{base}> <@var{size}> <@var{chip_width}> <@var{bus_width}> <@var{target}> [@option{driver options} ...]
Return information about the flash banks
@ -10509,8 +10501,8 @@ interpreter terminating it with @code{0x1a} and wait for the return
value (it will be terminated with @code{0x1a} as well). This can be
repeated as many times as desired without reopening the connection.
Remember that most of the OpenOCD commands need to be prefixed with
@code{ocd_} to get the results back. Sometimes you might also need the
It is not needed anymore to prefix the OpenOCD commands with
@code{ocd_} to get the results back. But sometimes you might need the
@command{capture} command.
See @file{contrib/rpc_examples/} for specific client implementations.