tinyriscv-openocd/tcl/target/stm32f0x.cfg

87 lines
2.3 KiB
INI
Raw Normal View History

# script for stm32f0x family
#
# stm32 devices support SWD transports only.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
set _CHIPNAME stm32f0x
}
set _ENDIAN little
# Work-area is a space in RAM used for flash programming
# By default use 4kB
if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
set _WORKAREASIZE 0x1000
}
#jtag scan chain
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# See STM Document RM0091
# Section 29.5.3
set _CPUTAPID 0x0bb11477
}
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
# flash size will be probed
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
# adapter speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
adapter_khz 1000
adapter_nsrst_delay 100
reset_config srst_nogate
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
cortex_m reset_config sysresetreq
}
proc stm32f0x_default_reset_start {} {
# Reset clock is HSI (8 MHz)
adapter_khz 1000
}
proc stm32f0x_default_examine_end {} {
# Enable debug during low power modes (uses more power)
mmw 0x40015804 0x00000006 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
# Stop watchdog counters during halt
mmw 0x40015808 0x00001800 0 ;# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
}
proc stm32f0x_default_reset_init {} {
# Configure PLL to boost clock to HSI x 6 (48 MHz)
mww 0x40021004 0x00100000 ;# RCC_CFGR = PLLMUL[2]
mmw 0x40021000 0x01000000 0 ;# RCC_CR[31:16] |= PLLON
mww 0x40022000 0x00000011 ;# FLASH_ACR = PRFTBE | LATENCY[0]
sleep 10 ;# Wait for PLL to lock
mmw 0x40021004 0x00000002 0 ;# RCC_CFGR |= SW[1]
# Boost JTAG frequency
adapter_khz 8000
}
# Default hooks
$_TARGETNAME configure -event examine-end { stm32f0x_default_examine_end }
$_TARGETNAME configure -event reset-start { stm32f0x_default_reset_start }
$_TARGETNAME configure -event reset-init { stm32f0x_default_reset_init }