2008-04-24 11:09:28 +00:00
< html >
< head >
< title > Test results for revision 607< / title >
< / head >
< body >
< H1 > Test cases< / H1 >
< H2 > Test case results< / H2 >
The test results are stored in seperate documents. One document for
each subversion number.
< table border = "1" >
< tr > < td > Test results< / td > < td > comment< / td > < / tr >
< tr > < td > 607< / a > < / td > < td > < / td > < / tr >
< tr > < td > < a href = "results/template.html" > template< / a > < / td > < td > Test results template< / td > < / tr >
< / table >
< H1 > SAM7S64< / H1 >
< H2 > Connectivity< / H2 >
< table border = 1 >
< tr >
< td > ID< / td >
< td > Target< / td >
< td > Interface< / td >
< td > Description< / td >
< td > Initial state< / td >
< td > Input< / td >
< td > Expected output< / td >
< td > Actual output< / td >
< td > Pass/Fail< / td >
< / tr >
< tr >
< td > < a name = "CON001" / > CON001< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Telnet connection< / td >
< td > Power on, jtag target attached< / td >
< td > On console, type< br > < code > telnet ip port< / code > < / td >
< td > < code > Open On-Chip Debugger< br > >< / code > < / td >
< td > < code > Open On-Chip Debugger< br > >< / code > < / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "CON002" / > CON002< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > GDB server connection< / td >
< td > Power on, jtag target attached< / td >
< td > On GDB console, type< br > < code > target remote ip:port< / code > < / td >
< td > < code > Remote debugging using 10.0.0.73:3333< / code > < / td >
< td > < code > Remote debugging using 10.0.0.73:3333< / code > < / td >
< td > PASS< / td >
< / tr >
< / table >
< H2 > Reset< / H2 >
< table border = 1 >
< tr >
< td > ID< / td >
< td > Target< / td >
< td > Interface< / td >
< td > Description< / td >
< td > Initial state< / td >
< td > Input< / td >
< td > Expected output< / td >
< td > Actual output< / td >
< td > Pass/Fail< / td >
< / tr >
< tr >
< td > < a name = "RES001" / > RES001< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Reset halt on a blank target< / td >
< td > Erase all the content of the flash< / td >
< td > Connect via the telnet interface and type < br > < code > reset halt< / code > < / td >
< td > Reset should return without error and the output should contain< br > < code > target state: halted< br > pc = 0< / code > < / td >
< td >
< code >
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)< br >
nSRST pulls nTRST, falling back to "reset run_and_halt"< br >
target state: halted< br >
target halted in ARM state due to debug request, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00100178
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "RES002" / > RES002< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Reset init on a blank target< / td >
< td > Erase all the content of the flash< / td >
< td > Connect via the telnet interface and type < br > < code > reset init< / code > < / td >
< td > Reset should return without error and the output should contain < br > < code > executing reset script 'name_of_the_script'< / code > < / td >
< td >
< code >
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)< br >
nSRST pulls nTRST, falling back to "reset run_and_init"< br >
target state: halted< br >
target halted in ARM state due to debug request, current mode: Supervisor< br >
cpsr: 0x600000d3 pc: 0x00003e24< br >
executing reset script 'event/sam7s256_reset.script'
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "RES003" / > RES003< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Reset after a power cycle of the target< / td >
< td > Reset the target then power cycle the target< / td >
< td > Connect via the telnet interface and type < br > < code > reset halt< / code > after the power was detected< / td >
< td > Reset should return without error and the output should contain< br > < code > target state: halted< / code > < / td >
< td >
< code >
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)< br >
nSRST pulls nTRST, falling back to "reset run_and_halt"< br >
target state: halted< br >
target halted in ARM state due to debug request, current mode: Supervisor< br >
cpsr: 0x300000d3 pc: 0x00003a38
< / code >
< / td >
< td > PASS< / td >
< / tr >
< / table >
< H2 > JTAG Speed< / H2 >
< table border = 1 >
< tr >
< td > ID< / td >
< td > Target< / td >
< td > ZY1000< / td >
< td > Description< / td >
< td > Initial state< / td >
< td > Input< / td >
< td > Expected output< / td >
< td > Actual output< / td >
< td > Pass/Fail< / td >
< / tr >
< tr >
< td > < a name = "SPD001" / > RES001< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > 16MHz on normal operation< / td >
< td > Reset init the target according to RES002 < / td >
< td > Exercise a memory access over the JTAG, for example < br > < code > mdw 0x0 32< / code > < / td >
< td > The command should run without any errors. If any JTAG checking errors happen, the test failed< / td >
< td >
< code >
> jtag_khz 16000< br >
> mdw 0 32< br >
0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
< / code >
< / td >
< td > PASS< / td >
< / tr >
< / table >
< H2 > Debugging< / H2 >
< table border = 1 >
< tr >
< td > ID< / td >
< td > Target< / td >
< td > Interface< / td >
< td > Description< / td >
< td > Initial state< / td >
< td > Input< / td >
< td > Expected output< / td >
< td > Actual output< / td >
< td > Pass/Fail< / td >
< / tr >
< tr >
< td > < a name = "DBG001" / > DBG001< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Load is working< / td >
< td > Reset init is working, RAM is accesible, GDB server is started< / td >
< td > On the console of the OS: < br >
< code > arm-elf-gdb test_ram.elf< / code > < br >
< code > (gdb) target remote ip:port< / code > < br >
< code > (gdb) load< / load >
< / td >
< td > Load should return without error, typical output looks like:< br >
< code >
Loading section .text, size 0x14c lma 0x0< br >
Start address 0x40, load size 332< br >
Transfer rate: 180 bytes/sec, 332 bytes/write.< br >
< / code >
< / td >
< td > < code >
(gdb) load< br >
Loading section .text, size 0x194 lma 0x200000< br >
Start address 0x200040, load size 404< br >
Transfer rate: 17470 bits/sec, 404 bytes/write.
< / code > < / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "DBG002" / > DBG002< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Software breakpoint< / td >
< td > Load the test_ram.elf application, use instructions from GDB001< / td >
< td > In the GDB console:< br >
< code >
(gdb) monitor arm7_9 sw_bkpts enable< br >
software breakpoints enabled< br >
(gdb) break main< br >
Breakpoint 1 at 0xec: file src/main.c, line 71.< br >
(gdb) continue< br >
Continuing.
< / code >
< / td >
< td > The software breakpoint should be reached, a typical output looks like:< br >
< code >
target state: halted< br >
target halted in ARM state due to breakpoint, current mode: Supervisor< br >
cpsr: 0x000000d3 pc: 0x000000ec< br >
< br >
Breakpoint 1, main () at src/main.c:71< br >
71 DWORD a = 1;
< / code >
< / td >
< td >
< code >
(gdb) break main< br >
Breakpoint 2 at 0x200134: file src/main.c, line 69.< br >
(gdb) c< br >
Continuing.< br >
target state: halted< br >
target halted in ARM state due to breakpoint, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00200134< br >
< br >
Breakpoint 2, main () at src/main.c:69< br >
69 DWORD a = 1;
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "DBG003" / > DBG003< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Single step in a RAM application< / td >
< td > Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002< / td >
< td > In GDB, type < br > < code > (gdb) step< / code > < / td >
< td > The next instruction should be reached, typical output:< br >
< code >
(gdb) step< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Abort< br >
cpsr: 0x20000097 pc: 0x000000f0< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Abort< br >
cpsr: 0x20000097 pc: 0x000000f4< br >
72 DWORD b = 2;
< / code >
< / td >
< td >
< code >
(gdb) step< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Abort< br >
cpsr: 0x20000097 pc: 0x000000f0< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Abort< br >
cpsr: 0x20000097 pc: 0x000000f4< br >
72 DWORD b = 2;
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "DBG004" / > DBG004< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Software break points are working after a reset< / td >
< td > Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002< / td >
< td > In GDB, type < br > < code >
(gdb) monitor reset< br >
(gdb) load< br >
(gdb) continue< br >
< / code > < / td >
< td > The breakpoint should be reached, typical output:< br >
< code >
target state: halted< br >
target halted in ARM state due to breakpoint, current mode: Supervisor< br >
cpsr: 0x000000d3 pc: 0x000000ec< br >
< br >
Breakpoint 1, main () at src/main.c:71< br >
71 DWORD a = 1;
< / code >
< / td >
< td > < code >
(gdb) moni reset< br >
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)< br >
target state: halted< br >
target halted in ARM state due to debug request, current mode: Supervisor< br >
cpsr: 0x600000d3 pc: 0x00003e28< br >
executing reset script 'event/sam7s256_reset.script'< br >
(gdb) load< br >
Loading section .text, size 0x194 lma 0x200000< br >
Start address 0x200040, load size 404< br >
Transfer rate: 20455 bits/sec, 404 bytes/write.< br >
(gdb) continue< br >
Continuing.< br >
target state: halted< br >
target halted in ARM state due to breakpoint, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00200134< br >
< br >
Breakpoint 2, main () at src/main.c:69< br >
69 DWORD a = 1;
< / code > < / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "DBG005" / > DBG005< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Hardware breakpoint< / td >
< td > Flash the test_rom.elf application. Make this test after FLA004 has passed< / td >
< td > Be sure that < code > gdb_memory_map< / code > and < code > gdb_flash_program< / code > are enabled. In GDB, type < br >
< code >
(gdb) monitor reset< br >
(gdb) load< br >
Loading section .text, size 0x194 lma 0x100000< br >
Start address 0x100040, load size 404< br >
Transfer rate: 179 bytes/sec, 404 bytes/write.< br >
(gdb) monitor arm7_9 force_hw_bkpts enable< br >
force hardware breakpoints enabled< br >
(gdb) break main< br >
Breakpoint 1 at 0x100134: file src/main.c, line 69.< br >
(gdb) continue< br >
< / code >
< / td >
< td > The breakpoint should be reached, typical output:< br >
< code >
Continuing.< br >
< br >
Breakpoint 1, main () at src/main.c:69< br >
69 DWORD a = 1;< br >
< / code >
< / td >
< td >
< code >
(gdb) break main< br >
Breakpoint 1 at 0x100134: file src/main.c, line 69.< br >
(gdb) c< br >
Continuing.< br >
target state: halted< br >
target halted in ARM state due to breakpoint, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00100134< br >
< br >
Breakpoint 1, main () at src/main.c:69< br >
69 DWORD a = 1;
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "DBG006" / > DBG006< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Hardware breakpoint is set after a reset< / td >
< td > Follow the instructions to flash and insert a hardware breakpoint from DBG005< / td >
< td > In GDB, type < br >
< code >
(gdb) monitor reset< br >
(gdb) monitor reg pc 0x100000< br >
pc (/32): 0x00100000< br >
(gdb) continue
< / code > < br >
where the value inserted in PC is the start address of the application
< / td >
< td > The breakpoint should be reached, typical output:< br >
< code >
Continuing.< br >
< br >
Breakpoint 1, main () at src/main.c:69< br >
69 DWORD a = 1;< br >
< / code >
< / td >
< td >
< code >
Continuing.< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00100040< br >
target state: halted< br >
target halted in ARM state due to breakpoint, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00100134< br >
< br >
Breakpoint 1, main () at src/main.c:69< br >
69 DWORD a = 1;
< / code > < br >
< b > Aren't there too many "halted" signs?< / b >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "DBG007" / > DBG007< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Single step in ROM< / td >
< td > Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed< / td >
< td > Be sure that < code > gdb_memory_map< / code > and < code > gdb_flash_program< / code > are enabled. In GDB, type < br >
< code >
(gdb) monitor reset< br >
(gdb) load< br >
Loading section .text, size 0x194 lma 0x100000< br >
Start address 0x100040, load size 404< br >
Transfer rate: 179 bytes/sec, 404 bytes/write.< br >
(gdb) monitor arm7_9 force_hw_bkpts enable< br >
force hardware breakpoints enabled< br >
(gdb) break main< br >
Breakpoint 1 at 0x100134: file src/main.c, line 69.< br >
(gdb) continue< br >
Continuing.< br >
< br >
Breakpoint 1, main () at src/main.c:69< br >
69 DWORD a = 1;< br >
(gdb) step
< / code >
< / td >
< td > The breakpoint should be reached, typical output:< br >
< code >
target state: halted< br >
target halted in ARM state due to single step, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x0010013c< br >
70 DWORD b = 2;< br >
< / code >
< / td >
< td > < code >
(gdb) step< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x00100138< br >
target state: halted< br >
target halted in ARM state due to single step, current mode: Supervisor< br >
cpsr: 0x60000013 pc: 0x0010013c< br >
70 DWORD b = 2;
< / code > < / td >
< td > PASS< / td >
< / tr >
< / table >
< H2 > RAM access< / H2 >
Note: these tests are not designed to test/debug the target, but to test functionalities!
< table border = 1 >
< tr >
< td > ID< / td >
< td > Target< / td >
< td > Interface< / td >
< td > Description< / td >
< td > Initial state< / td >
< td > Input< / td >
< td > Expected output< / td >
< td > Actual output< / td >
< td > Pass/Fail< / td >
< / tr >
< tr >
< td > < a name = "RAM001" / > RAM001< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > 32 bit Write/read RAM< / td >
< td > Reset init is working< / td >
< td > On the telnet interface< br >
< code > > mww ram_address 0xdeadbeef 16< br >
> mdw ram_address 32
< / code >
< / td >
< td > The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef.< br >
< code >
> mww 0x0 0xdeadbeef 16< br >
> mdw 0x0 32< br >
0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388< br >
0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388< br >
< / code >
< / td >
< td >
< code >
> mww 0x00200000 0xdeadbeef 16< br >
> mdw 0x00200000 32< br >
0x00200000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x00200020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x00200040: e59f10b4 e3a00902 e5810004 e59f00ac e59f10ac e5810000 e3e010ff e59f00a4< br >
0x00200060: e5810060 e59f10a0 e3e00000 e5810130 e5810124 e321f0db e59fd090 e321f0d7
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "RAM002" / > RAM002< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > 16 bit Write/read RAM< / td >
< td > Reset init is working< / td >
< td > On the telnet interface< br >
< code > > mwh ram_address 0xbeef 16< br >
> mdh ram_address 32
< / code >
< / td >
< td > The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef.< br >
< code >
> mwh 0x0 0xbeef 16< br >
> mdh 0x0 32< br >
0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef< br >
0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000< br >
>
< / code >
< / td >
< td > < code >
> mwh 0x00200000 0xbeef 16< br >
> mdh 0x00200000 32< br >
0x00200000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef< br >
0x00200020: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
< / code > < / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "RAM003" / > RAM003< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > 8 bit Write/read RAM< / td >
< td > Reset init is working< / td >
< td > On the telnet interface< br >
< code > > mwb ram_address 0xab 16< br >
> mdb ram_address 32
< / code >
< / td >
< td > The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab.< br >
< code >
> mwb ram_address 0xab 16< br >
> mdb ram_address 32< br >
0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00< br >
>
< / code >
< / td >
< td > < code >
> mwb 0x00200000 0xab 16< br >
> mdb 0x00200000 32< br >
0x00200000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
< / code > < / td >
< td > PASS< / td >
< / tr >
< / table >
< H2 > Flash access< / H2 >
< table border = 1 >
< tr >
< td > ID< / td >
< td > Target< / td >
< td > Interface< / td >
< td > Description< / td >
< td > Initial state< / td >
< td > Input< / td >
< td > Expected output< / td >
< td > Actual output< / td >
< td > Pass/Fail< / td >
< / tr >
< tr >
< td > < a name = "FLA001" / > FLA001< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Flash probe< / td >
< td > Reset init is working< / td >
< td > On the telnet interface:< br >
< code > > flash probe 0< / code >
< / td >
< td > The command should execute without error. The output should state the name of the flash and the starting address. An example of output:< br >
< code > flash 'ecosflash' found at 0x01000000< / code >
< / td >
< td >
< code >
> flash probe 0< br >
flash 'at91sam7' found at 0x00100000
< / code >
< / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "FLA002" / > FLA002< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > flash fillw< / td >
< td > Reset init is working, flash is probed< / td >
< td > On the telnet interface< br >
< code > > flash fillw 0x1000000 0xdeadbeef 16
< / code >
< / td >
< td > The commands should execute without error. The output looks like:< br >
< code >
wrote 64 bytes to 0x01000000 in 11.610000s (0.091516 kb/s)
< / code > < br >
To verify the contents of the flash:< br >
< code >
> mdw 0x1000000 32< br >
0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
< / code >
< / td >
< td > < code >
> flash fillw 0x100000 0xdeadbeef 16< br >
wrote 64 bytes to 0x00100000 in 1.110000s (0.957207 kb/s)< br >
> mdw 0x100000 32< br >
0x00100000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x00100020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef< br >
0x00100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
< / code > < / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "FLA003" / > FLA003< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Flash erase< / td >
< td > Reset init is working, flash is probed< / td >
< td > On the telnet interface< br >
< code > > flash erase_address 0x1000000 0x2000
< / code >
< / td >
< td > The commands should execute without error.< br >
< code >
erased address 0x01000000 length 8192 in 4.970000s
< / code >
To check that the flash has been erased, read at different addresses. The result should always be 0xff.
< code >
> mdw 0x1000000 32< br >
0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
< / code >
< / td >
< td > < code >
> flash erase_address 0x100000 0x2000< br >
erased address 0x00100000 length 8192 in 0.510000s< br >
> mdw 0x100000 32< br >
0x00100000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00100020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
0x00100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff< br >
>
< / code > < / td >
< td > PASS< / td >
< / tr >
< tr >
< td > < a name = "FLA004" / > FLA004< / td >
< td > SAM7S64< / td >
< td > ZY1000< / td >
< td > Loading to flash from GDB< / td >
< td > Reset init is working, flash is probed, connectivity to GDB server is working< / td >
< td > Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. < br >
< code >
(gdb) target remote ip:port< br >
(gdb) monitor reset< br >
(gdb) load< br >
Loading section .text, size 0x194 lma 0x100000< br >
Start address 0x100040, load size 404< br >
Transfer rate: 179 bytes/sec, 404 bytes/write.
(gdb) monitor verify_image path_to_elf_file
< / code >
< / td >
< td > The output should look like:< br >
< code >
verified 404 bytes in 5.060000s
< / code > < br >
The failure message is something like:< br >
< code > Verify operation failed address 0x00200000. Was 0x00 instead of 0x18< / code >
< / td >
< td >
< code >
(gdb) load< br >
Loading section .text, size 0x194 lma 0x100000< br >
Start address 0x100040, load size 404< br >
Transfer rate: 1540 bits/sec, 404 bytes/write.< br >
(gdb) monitor verify_image /tftp/10.0.0.9/c:\workspace/ecosboard/ecosboard/phi/openocd/rep/testing/examples/SAM7S256Test/test_rom.elf< br >
verified 404 bytes in 4.860000s
< / code >
< / td >
< td > PASS< / td >
< / tr >
< / table >
< / body >
2008-04-24 09:21:42 +00:00
< / html >
