tinyriscv-openocd/tcl/board/glyn_tonga2.cfg

171 lines
6.0 KiB
INI
Raw Normal View History

#
# Glyn Tonga2 SO-DIMM CPU module (Toshiba TMPA900CMXBG, ARM9)
#
# http://toshiba-mikrocontroller.de/sites/TMPA900CPUBOARDStarter.htm
#
# Hardware on the S0-DIMM module:
# - Toshiba TMPA900CMXBG (ARM9, ARM926EJ-S, max. 200MHz)
# - DDR SDRAM: Hynix H5MS5162DFR-J3M (64Mbyte, x16, 1.8V, 166/83MHz at CL3/2)
# - NAND flash: Samsung K9F2G08U0B-PIB0 (256M x 8 Bit, 3.3V)
# - Ethernet: SMSC LAN9221I-ABZJ (10/100Mbit, Non-PCI, 16 bit interface)
#
source [find target/tmpa900.cfg]
########################
# Target configuration #
########################
$_TARGETNAME configure -event reset-init { tonga2_init }
proc tonga2_init { } {
######################
# PLL initialization #
######################
# Clock overview (see datasheet chapter 3.5.2, page 57):
# - fs: Low-frequency oscillator
# - fOSCH: High-frequency oscillator (24MHz on this board)
# - fPLL = fOSCH * multiplier (where multiplier can be 6 or 8)
# - fFCLK = fPLL / gear (where gear can be 1/2/4/8)
# - fHCLK is always fFCLK/2. fPCLK is also fFCLK/2.
#
# We select multiplier = 8 and gear = 1, so
# fFCLK = fOSCH * 8 / 1 = 192MHz.
# SYSCR3 (System Control Register 3): Disable and configure PLL.
# - PLL operation control: off
# - PLL constant value setting 1: always 0, as per datasheet
# - PLL constant value setting 2: x8 (multiplier = 8)
mww 0xf005000c 0x00000007
# SYSCR4 (System Control Register 4): Configure PLL.
# - PLL constant value setting 3: 140MHz or more
# - PLL constant value setting 4: always 1, as per datasheet
# - PLL constant value setting 5: 140MHz or more
mww 0xf0050010 0x00000065
# SYSCR3 (System Control Register 3): Enable PLL.
# - PLL operation control: on
# - All other bits remain set as above.
mww 0xf005000c 0x00000087
# Wait for PLL to stabilize.
sleep 10
# SYSCR2 (System Control Register 2): Switch from fOSCH to fPLL.
# - Selection of the PLL output clock: fPLL
mww 0xf0050008 0x00000002
# SYSCR1 (System Control Register 1):
# - Clock gear programming: fc/1 (i.e., gear = 1, don't divide).
mww 0xf0050004 0x00000000
# CLKCR5 (Clock Control Register 5): Set bits 3 and 6. The datasheet
# says the bits are reserved, but also recommends "Write as one".
mww 0xf0050054 0x00000048
##############################################################
# Dynamic Memory Controller (DMC) / DDR SDRAM initialization #
##############################################################
# PMC (Power Management Controller):
# PMCDRV (External Port "Driverbility" control register):
# Bits DRV_MEM0/DRV_MEM1 (memory relation port drive power):
mww 0xf0020260 0x00000003 ;# Select 1.8V +/- 0.1V
# Setup DDR SDRAM timing parameters for our specific chip.
mww 0xf4310014 0x00000004 ;# cas_latency = 2
mww 0xf4310018 0x00000001 ;# t_dqss = 1
mww 0xf431001c 0x00000002 ;# t_mrd = 2
mww 0xf4310020 0x0000000a ;# t_ras = 10
mww 0xf4310024 0x0000000a ;# t_rc = 10
mww 0xf4310028 0x00000013 ;# t_rcd = 3, schedule_rcd = 2
mww 0xf431002c 0x0000010a ;# t_rfc = 10, schedule_rfc = 8
mww 0xf4310030 0x00000013 ;# t_rp = 3, schedule_rp = 2
mww 0xf4310034 0x00000002 ;# t_rrd = 2
mww 0xf4310038 0x00000002 ;# t_wr = 2
mww 0xf431003c 0x00000001 ;# t_wtr = 1
mww 0xf4310040 0x0000000a ;# t_xp = 10
mww 0xf4310044 0x0000000c ;# t_xsr = 12
mww 0xf4310048 0x00000014 ;# t_esr = 20
# dmc_memory_cfg_5 (DMC Memory Configuration register):
# Set memory configuration:
# column_bits = 10, row_bits = 13, ap-bit = 10, power_down_prd = 0,
# auto_power_down = disable, stop_mem_clock = disable, memory_burst = 4
mww 0xf431000c 0x00010012
# dmc_user_config_5 (DMC user_config register):
# Data bus width of DDR SDRAM: 16 bit
mww 0xf4310304 0x00000058
# dmc_refresh_prd_5 (DMC Refresh Period register):
# Auto refresh: every 2656 (0xa60) DMCSCLK periods.
mww 0xf4310010 0x00000a60
# dmc_chip_0_cfg_5 (DMC chip_0_cfg registers):
# - SDRAM address structure: bank, row, column
# - address_match = 01000000 (start address [31:24])
# - address_mask = 11111100 (start address [31:24] mask value)
mww 0xf4310200 0x000140fc
# Initialize the DDR SDRAM chip.
# dmc_direct_cmd_5 (DMC Direct Command register).
# See datasheet chapter 3.10.5.1, page 268.
mww 0xf4310008 0x000c0000 ;# RAM init: NOP
mww 0xf4310008 0x00000000 ;# RAM init: Precharge all
mww 0xf4310008 0x00040000 ;# RAM init: Autorefresh
mww 0xf4310008 0x00040000 ;# RAM init: Autorefresh
mww 0xf4310008 0x00080032 ;# RAM init: addr_13_to_0 = 0x32
mww 0xf4310008 0x000c0000 ;# RAM init: NOP
mww 0xf4310008 0x000a0000 ;# RAM init: bank_addr = bank 2
# dmc_id_<0-5>_cfg_5 (DMC id_<0-5>_cfg registers):
# Set min./max. QoS values.
# - 0x5: Enable QoS, max. QoS = 1
# - 0xb: Enable QoS, min. QoS = 2
mww 0xf4310100 0x00000005 ;# AHB0: CPU Data
mww 0xf4310104 0x00000005 ;# AHB1: CPU Inst
mww 0xf4310108 0x0000000b ;# AHB2: LCDC
mww 0xf431010c 0x00000005 ;# AHB3: LCDDA, USB
mww 0xf4310110 0x00000005 ;# AHB4: DMA1
mww 0xf4310114 0x00000005 ;# AHB5: DMA2
# dmc_memc_cmd_5 (DMC Memory Controller Command register):
# Change DMC state to ready.
mww 0xf4310004 0x00000000 ;# memc_cmd = "Go"
# EBI: SMC Timeout register
mww 0xf00a0050 0x00000001 ;# smc_timeout = 1
########################################################
# Static Memory Controller (SMC) / SRAM initialization #
########################################################
# smc_set_cycles_5 (SMC Set Cycles register):
# tRC = 10, tWC = 10, tCEOE = 7, tWP = 5, tPC=2, tTR=2
mww 0xf4311014 0x0004afaa
# smc_set_opmode_5 (SMC Set Opmode register):
# Memory data bus width = 16 bits, async read mode, read burst
# length = 1 beat, async write mode, write burst length = 1 beat,
# byte enable (SMCBE0-1) timing = SMCCSn timing, memory burst boundary
# split setting = burst can cross any address boundary
mww 0xf4311018 0x00000001
# smc_direct_cmd_5 (SMC Direct Command register):
# cmd_type = UpdateRegs, chip_select = CS1
mww 0xf4311010 0x00c00000
}
#######################
# Flash configuration #
#######################
# TODO: Implement NAND support.