tinyriscv-openocd/tcl/target/lpc17xx.cfg

# Main file for NXP LPC17xx Cortex-M3
#
# !!!!!!
#
# This file should not be included directly, rather
# by the lpc1751.cfg, lpc1752.cfg, etc. which set the
# needed variables to the appropriate values.
#
# !!!!!!

# LPC17xx chips support both JTAG and SWD transports.
# Adapt based on what transport is active.
source [find target/swj-dp.tcl]

if { [info exists CHIPNAME] } {
	set _CHIPNAME $CHIPNAME
} else {
	error "_CHIPNAME not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
}

# After reset the chip is clocked by the ~4MHz internal RC oscillator.
# When board-specific code (reset-init handler or device firmware)
# configures another oscillator and/or PLL0, set CCLK to match; if
# you don't, then flash erase and write operations may misbehave.
# (The ROM code doing those updates cares about core clock speed...)
#
# CCLK is the core clock frequency in KHz
if { [info exists CCLK] } {
	set _CCLK $CCLK
} else {
	set _CCLK 4000
}

if { [info exists CPUTAPID] } {
	set _CPUTAPID $CPUTAPID
} else {
	error "_CPUTAPID not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
}

if { [info exists CPURAMSIZE] } {
  set _CPURAMSIZE $CPURAMSIZE
} else {
	error "_CPURAMSIZE not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
}

if { [info exists CPUROMSIZE] } {
  set _CPUROMSIZE $CPUROMSIZE
} else {
	error "_CPUROMSIZE not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)."
}

#jtag newtap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -chain-position $_TARGETNAME

# The LPC17xx devices have 8/16/32kB of SRAM In the ARMv7-M "Code" area (at 0x10000000)
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_CPURAMSIZE

# The LPC17xx devies have 32/64/128/256/512kB of flash memory, managed by ROM code
# (including a boot loader which verifies the flash exception table's checksum).
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME lpc2000 0x0 $_CPUROMSIZE 0 0 $_TARGETNAME \
	lpc1700 $_CCLK calc_checksum

# Run with *real slow* clock by default since the
# boot rom could have been playing with the PLL, so
# we have no idea what clock the target is running at.
adapter_khz 10

# delays on reset lines
adapter_nsrst_delay 200
if {$using_jtag} {
 jtag_ntrst_delay 200
}

$_TARGETNAME configure -event reset-init {
	# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
	# "User Flash Mode" where interrupt vectors are _not_ remapped,
	# and reside in flash instead).
	#
	# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
	# Bit Symbol Value Description Reset
	# value
	# 0 MAP Memory map control. 0
	# 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
	# 1 User mode. The on-chip Flash memory is mapped to address 0.
	# 31:1 - Reserved. The value read from a reserved bit is not defined. NA
	#
	# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user

	mww 0x400FC040 0x01
}

# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
cortex_m reset_config sysresetreq