103 lines
3.5 KiB
Plaintext
103 lines
3.5 KiB
Plaintext
/*
|
|
ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
|
|
2011 Giovanni Di Sirio.
|
|
|
|
This file is part of ChibiOS/RT.
|
|
|
|
ChibiOS/RT is free software; you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation; either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
ChibiOS/RT is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/**
|
|
* @defgroup AVR_DRIVERS AVR Drivers
|
|
* @details This section describes all the supported drivers on the AVR
|
|
* platform and the implementation details of the single drivers.
|
|
*
|
|
* @ingroup platforms
|
|
*/
|
|
|
|
/**
|
|
* @defgroup AVR_HAL AVR Initialization Support
|
|
* @details On the AVR platform the HAL driver is a stub and does not perform
|
|
* any platform-specific initialization, it still performs the
|
|
* initialization of the other drivers.
|
|
*
|
|
* @ingroup AVR_DRIVERS
|
|
*/
|
|
|
|
/**
|
|
* @defgroup AVR_PAL AVR PAL Support
|
|
* @details The AVR PAL driver uses the PORT peripherals.
|
|
*
|
|
* @section avr_pal_1 Supported HW resources
|
|
* - PORTA.
|
|
* - PORTB.
|
|
* - PORTC.
|
|
* - PORTD.
|
|
* - PORTE.
|
|
* - PORTF.
|
|
* - PORTG.
|
|
* .
|
|
* @section avr_pal_2 AVR PAL driver implementation features
|
|
* The AVR PAL driver implementation fully supports the following hardware
|
|
* capabilities:
|
|
* - 8 bits wide ports.
|
|
* - Atomic set/reset functions.
|
|
* - Output latched regardless of the pad setting.
|
|
* - Direct read of input pads regardless of the pad setting.
|
|
* .
|
|
* @section avr_pal_3 Supported PAL setup modes
|
|
* The AVR PAL driver supports the following I/O modes:
|
|
* - @p PAL_MODE_RESET.
|
|
* - @p PAL_MODE_UNCONNECTED.
|
|
* - @p PAL_MODE_INPUT.
|
|
* - @p PAL_MODE_INPUT_PULLUP.
|
|
* - @p PAL_MODE_INPUT_ANALOG.
|
|
* - @p PAL_MODE_OUTPUT_PUSHPULL.
|
|
* .
|
|
* Any attempt to setup an invalid mode is ignored.
|
|
*
|
|
* @section avr_pal_4 Suboptimal behavior
|
|
* The AVR PORT is less than optimal in several areas, the limitations
|
|
* should be taken in account while using the PAL driver:
|
|
* - Pad/port toggling operations are not atomic.
|
|
* - Pad/group mode setup is not atomic.
|
|
* - Group set+reset function is not atomic.
|
|
* - Writing on pads/groups/ports programmed as input with pull-up
|
|
* resistor changes the resistor setting because the output latch is
|
|
* used for resistor selection.
|
|
* - The PORT registers layout on some devices is not regular (it does
|
|
* not have contiguous PIN, DDR, PORT registers in this order), such
|
|
* ports cannot be accessed using the PAL driver. For example, PORT F
|
|
* on ATmega128. Verify the user manual of your device.
|
|
* .
|
|
* @ingroup AVR_DRIVERS
|
|
*/
|
|
|
|
/**
|
|
* @defgroup AVR_SERIAL AVR Serial Support
|
|
* @details The AVR Serial driver uses the USART peripherals in a
|
|
* buffered, interrupt driven, implementation.
|
|
*
|
|
* @section avr_serial_1 Supported HW resources
|
|
* The serial driver can support any of the following hardware resources:
|
|
* - USART0.
|
|
* - USART1.
|
|
* .
|
|
* @section avr_serial_2 AVR Serial driver implementation features
|
|
* - Each USART can be independently enabled and programmed.
|
|
* - Fully interrupt driven.
|
|
* .
|
|
* @ingroup AVR_DRIVERS
|
|
*/
|