zcy
/
tinySA
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
tinySA/os/hal/ports/KINETIS/KL2x/hal_lld.c

308 lines
12 KiB
C
Raw Blame History

/*
ChibiOS - Copyright (C) 2013-2015 Fabio Utzig
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
/**
* @file KL2x/hal_lld.c
* @brief Kinetis KL2x HAL Driver subsystem low level driver source.
*
* @addtogroup HAL
* @{
*/
#include "osal.h"
#include "hal.h"
/*===========================================================================*/
/* Driver local definitions. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver exported variables. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver local variables and types. */
/*===========================================================================*/
#ifdef __CC_ARM
__attribute__ ((section(".ARM.__at_0x400")))
#else
__attribute__ ((used, section(".cfmconfig")))
#endif
const uint8_t _cfm[0x10] = {
0xFF, /* NV_BACKKEY3: KEY=0xFF */
0xFF, /* NV_BACKKEY2: KEY=0xFF */
0xFF, /* NV_BACKKEY1: KEY=0xFF */
0xFF, /* NV_BACKKEY0: KEY=0xFF */
0xFF, /* NV_BACKKEY7: KEY=0xFF */
0xFF, /* NV_BACKKEY6: KEY=0xFF */
0xFF, /* NV_BACKKEY5: KEY=0xFF */
0xFF, /* NV_BACKKEY4: KEY=0xFF */
0xFF, /* NV_FPROT3: PROT=0xFF */
0xFF, /* NV_FPROT2: PROT=0xFF */
0xFF, /* NV_FPROT1: PROT=0xFF */
0xFF, /* NV_FPROT0: PROT=0xFF */
0x7E, /* NV_FSEC: KEYEN=1,MEEN=3,FSLACC=3,SEC=2 */
0xFF, /* NV_FOPT: ??=1,??=1,FAST_INIT=1,LPBOOT1=1,RESET_PIN_CFG=1,
NMI_DIS=1,EZPORT_DIS=1,LPBOOT0=1 */
0xFF,
0xFF
};
/*===========================================================================*/
/* Driver local functions. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver interrupt handlers. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver exported functions. */
/*===========================================================================*/
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
}
/**
* @brief KL2x clocks and PLL initialization.
* @note All the involved constants come from the file @p board.h.
* @note This function should be invoked just after the system reset.
*
* @special
*/
void kl2x_clock_init(void) {
#if !KINETIS_NO_INIT
/* Disable COP watchdog */
SIM->COPC = 0;
/* Enable PORTA */
SIM->SCGC5 |= SIM_SCGC5_PORTA;
/* --- MCG mode: FEI (default out of reset) ---
f_MCGOUTCLK = f_int * F
F is the FLL factor selected by C4[DRST_DRS] and C4[DMX32] bits.
Typical f_MCGOUTCLK = 21 MHz immediately after reset.
C4[DMX32]=0 and C4[DRST_DRS]=00 => FLL factor=640.
C3[SCTRIM] and C4[SCFTRIM] factory trim values apply to f_int. */
/* System oscillator drives 32 kHz clock (OSC32KSEL=0) */
SIM->SOPT1 &= ~SIM_SOPT1_OSC32KSEL_MASK;
#if KINETIS_MCG_MODE == KINETIS_MCG_MODE_FEI
/* This is the default mode at reset. */
/* The MCGOUTCLK is divided by OUTDIV1 and OUTDIV4:
* OUTDIV1 (divider for core/system and bus/flash clock)
* OUTDIV4 (additional divider for bus/flash clock) */
SIM->CLKDIV1 =
SIM_CLKDIV1_OUTDIV1(1) | /* OUTDIV1 = divide-by-2 => 24 MHz */
SIM_CLKDIV1_OUTDIV4(0); /* OUTDIV4 = divide-by-1 => 24 MHz */
#elif KINETIS_MCG_MODE == KINETIS_MCG_MODE_FEE
/*
* FLL Enabled External (FEE) MCG Mode
* 24 MHz core, 12 MHz bus - using 32.768 kHz crystal with FLL.
* f_MCGOUTCLK = (f_ext / FLL_R) * F
* = (32.768 kHz ) *
* FLL_R is the reference divider selected by C1[FRDIV]
* F is the FLL factor selected by C4[DRST_DRS] and C4[DMX32].
*
* Then the core/system and bus/flash clocks are divided:
* f_SYS = f_MCGOUTCLK / OUTDIV1 = 48 MHz / 1 = 48 MHz
* f_BUS = f_MCGOUTCLK / OUTDIV1 / OUTDIV4 = MHz / 4 = 24 MHz
*/
SIM->SOPT2 =
SIM_SOPT2_TPMSRC(1); /* MCGFLLCLK clock or MCGPLLCLK/2 */
/* PLLFLLSEL=0 -> MCGFLLCLK */
/* The MCGOUTCLK is divided by OUTDIV1 and OUTDIV4:
* OUTDIV1 (divider for core/system and bus/flash clock)
* OUTDIV4 (additional divider for bus/flash clock) */
SIM->CLKDIV1 =
SIM_CLKDIV1_OUTDIV1(KINETIS_MCG_FLL_OUTDIV1 - 1) |
SIM_CLKDIV1_OUTDIV4(KINETIS_MCG_FLL_OUTDIV4 - 1);
/* EXTAL0 and XTAL0 */
PORTA->PCR[18] &= ~0x01000700; /* Set PA18 to analog (default) */
PORTA->PCR[19] &= ~0x01000700; /* Set PA19 to analog (default) */
OSC0->CR = 0;
/* From KL25P80M48SF0RM section 24.5.1.1 "Initializing the MCG". */
/* To change from FEI mode to FEE mode: */
/* (1) Select the external clock source in C2 register.
Use low-power OSC mode (HGO0=0) which enables internal feedback
resistor, for 32.768 kHz crystal configuration. */
MCG->C2 =
MCG_C2_RANGE0(0) | /* low frequency range (<= 40 kHz) */
MCG_C2_EREFS0; /* external reference (using a crystal) */
/* (2) Write to C1 to select the clock mode. */
MCG->C1 = /* Clear the IREFS bit to switch to the external reference. */
MCG_C1_CLKS_FLLPLL | /* Use FLL for system clock, MCGCLKOUT. */
MCG_C1_FRDIV(0); /* Don't divide 32kHz ERCLK FLL reference. */
MCG->C6 = 0; /* PLLS=0: Select FLL as MCG source, not PLL */
/* Loop until S[OSCINIT0] is 1, indicating the
crystal selected by C2[EREFS0] has been initialized. */
while ((MCG->S & MCG_S_OSCINIT0) == 0)
;
/* Loop until S[IREFST] is 0, indicating the
external reference is the current reference clock source. */
while ((MCG->S & MCG_S_IREFST) != 0)
; /* Wait until external reference clock is FLL reference. */
/* (1)(e) Loop until S[CLKST] indicates FLL feeds MCGOUTCLK. */
while ((MCG->S & MCG_S_CLKST_MASK) != MCG_S_CLKST_FLL)
; /* Wait until FLL has been selected. */
/* --- MCG mode: FEE --- */
/* Set frequency range for DCO output (MCGFLLCLK). */
MCG->C4 = (KINETIS_MCG_FLL_DMX32 ? MCG_C4_DMX32 : 0) |
MCG_C4_DRST_DRS(KINETIS_MCG_FLL_DRS);
/* Wait for the FLL lock time; t[fll_acquire][max] = 1 ms */
/* TODO - not implemented - is it required? Freescale example code
seems to omit it. */
#elif KINETIS_MCG_MODE == KINETIS_MCG_MODE_PEE
/*
* PLL Enabled External (PEE) MCG Mode
* 48 MHz core, 24 MHz bus - using 8 MHz crystal with PLL.
* f_MCGOUTCLK = (OSCCLK / PLL_R) * M
* = 8 MHz / 2 * 24 = 96 MHz
* PLL_R is the reference divider selected by C5[PRDIV0]
* M is the multiplier selected by C6[VDIV0]
*
* Then the core/system and bus/flash clocks are divided:
* f_SYS = f_MCGOUTCLK / OUTDIV1 = 96 MHz / 2 = 48 MHz
* f_BUS = f_MCGOUTCLK / OUTDIV1 / OUTDIV4 = 96 MHz / 4 = 24 MHz
*/
/* The MCGOUTCLK is divided by OUTDIV1 and OUTDIV4:
* OUTDIV1 (divider for core/system and bus/flash clock)
* OUTDIV4 (additional divider for bus/flash clock) */
SIM->CLKDIV1 =
SIM_CLKDIV1_OUTDIV1(1) | /* OUTDIV1 = divide-by-2 => 48 MHz */
SIM_CLKDIV1_OUTDIV4(1); /* OUTDIV4 = divide-by-2 => 24 MHz */
SIM->SOPT2 =
SIM_SOPT2_TPMSRC(1) | /* MCGFLLCLK clock or MCGPLLCLK/2 */
SIM_SOPT2_PLLFLLSEL; /* PLLFLLSEL=MCGPLLCLK/2 */
/* EXTAL0 and XTAL0 */
PORTA->PCR[18] &= ~0x01000700; /* Set PA18 to analog (default) */
PORTA->PCR[19] &= ~0x01000700; /* Set PA19 to analog (default) */
OSC0->CR = 0;
/* From KL25P80M48SF0RM section 24.5.1.1 "Initializing the MCG". */
/* To change from FEI mode to FBE mode: */
/* (1) Select the external clock source in C2 register.
Use low-power OSC mode (HGO0=0) which enables internal feedback
resistor since FRDM-KL25Z has feedback resistor R25 unpopulated.
Use high-gain mode by setting C2[HGO0] instead if external
feedback resistor Rf is installed. */
MCG->C2 =
MCG_C2_RANGE0(2) | /* very high frequency range */
MCG_C2_EREFS0; /* external reference (using a crystal) */
/* (2) Write to C1 to select the clock mode. */
MCG->C1 = /* Clear the IREFS bit to switch to the external reference. */
MCG_C1_CLKS_ERCLK | /* Use ERCLK for system clock, MCGCLKOUT. */
MCG_C1_FRDIV(3); /* Divide ERCLK / 256 for FLL reference. */
/* Note: FLL reference frequency must be 31.25 kHz to 39.0625 kHz.
8 MHz / 256 = 31.25 kHz. */
MCG->C4 &= ~(MCG_C4_DMX32 | MCG_C4_DRST_DRS_MASK);
MCG->C6 = 0; /* PLLS=0: Select FLL as MCG source, not PLL */
/* (3) Once configuration is set, wait for MCG mode change. */
/* From KL25P80M48SF0RM section 24.5.31: */
/* (1)(c) Loop until S[OSCINIT0] is 1, indicating the
crystal selected by C2[EREFS0] has been initialized. */
while ((MCG->S & MCG_S_OSCINIT0) == 0)
;
/* (1)(d) Loop until S[IREFST] is 0, indicating the
external reference is the current reference clock source. */
while ((MCG->S & MCG_S_IREFST) != 0)
; /* Wait until external reference clock is FLL reference. */
/* (1)(e) Loop until S[CLKST] is 2'b10, indicating
the external reference clock is selected to feed MCGOUTCLK. */
while ((MCG->S & MCG_S_CLKST_MASK) != MCG_S_CLKST_ERCLK)
; /* Wait until external reference clock has been selected. */
/* --- MCG mode: FBE (FLL bypassed, external crystal) ---
Now the MCG is in FBE mode.
Although the FLL is bypassed, it is still on. */
/* (2) Then configure C5[PRDIV0] to generate the
correct PLL reference frequency. */
MCG->C5 = MCG_C5_PRDIV0(1); /* PLL External Reference Divide by 2 */
/* (3) Then from FBE transition to PBE mode. */
/* (3)(b) C6[PLLS]=1 to select PLL. */
/* (3)(b) C6[VDIV0]=5'b0000 (x24) 2 MHz * 24 = 48 MHz. */
MCG->C6 = MCG_C6_PLLS | MCG_C6_VDIV0(0);
/* (3)(d) Loop until S[PLLST], indicating PLL
is the PLLS clock source. */
while ((MCG->S & MCG_S_PLLST) == 0)
; /* wait until PLL is the PLLS clock source. */
/* (3)(e) Loop until S[LOCK0] is set, indicating the PLL has acquired lock. */
/* PLL selected as MCG source. VDIV0=00000 (Multiply=24). */
while ((MCG->S & MCG_S_LOCK0) == 0)
; /* wait until PLL locked */
/* --- MCG mode: PBE (PLL bypassed, external crystal) --- */
/* (4) Transition from PBE mode to PEE mode. */
/* (4)(a) C1[CLKS] = 2'b00 to select PLL output as system clock source. */
// Switch to PEE mode
// Select PLL output (CLKS=0)
// FLL external reference divider (FRDIV=3)
// External reference clock for FLL (IREFS=0)
MCG->C1 = MCG_C1_CLKS(0) |
MCG_C1_FRDIV(3);
/* (4)(b) Loop until S[CLKST] are 2'b11, indicating the PLL output is selected for MCGOUTCLK. */
while ((MCG->S & MCG_S_CLKST_MASK) != MCG_S_CLKST_PLL)
; /* wait until clock switched to PLL output */
/* --- MCG mode: PEE (PLL enabled, external crystal) --- */
#else /* KINETIS_MCG_MODE != KINETIS_MCG_MODE_PEE */
#error Unimplemented KINETIS_MCG_MODE
#endif /* KINETIS_MCG_MODE != KINETIS_MCG_MODE_PEE */
#endif /* !KINETIS_NO_INIT */
}
/**
* @brief Platform early initialization.
* @note All the involved constants come from the file @p board.h.
* @note This function is meant to be invoked early during the system
* initialization, it is usually invoked from the file
* @p board.c.
*
* @special
*/
void platform_early_init(void) {
}
/** @} */
Reference in New Issue View Git Blame Copy Permalink